Warrant Installation Manual Model: 59397 Noble Bronze 59398 Brushed Nickel 51473 Flat Matte Black Fan weight ±2 lbs: 24.9 lbs (11.3 kg) ©2021 Hunter Fan Co.
Congratulations on purchasing your new Hunter® ceiling fan! The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. We are here to help! This Instruction Manual is designed to make installation as simple as possible.
1886 Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component. Wood Screw Hunter Pro Tip: Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag.
1886 Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit. Check the room dimensions: Check the outlet box: 30 inches from blade tip to nearest wall or obstruction You must be able to secure the fan to building structure or fan-rated outlet box.
1886 You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. Hunter Pro Tip: The machine screws are the ones that came with your outlet box. WARNING Do this first! To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
1886 STEP STEP Installing the Downrod 4 5 Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. Lower the adapter cover until it rests flush against the motor housing. WARNING FAN FALL HAZARD To prevent SERIOUS INJURY or DEATH: • ALWAYS tighten setscrew with pliers. • DO NOT hand tighten setscrew. • CHECK the setscrew is tight using pliers each time you change fan direction.
1886 Wiring the Fan We know wiring is hard. Let’s make it easier. Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. Hunter Pro Tip: You are going to need these: Here is how to connect the wires: Push the bare metal ends of the wires together and slide a wire nut over them. Then, twist the wire nut clockwise until tight.
1886 Installing the Canopy Insert the two canopy screws found in the hardware bag. x2 Canopy Screw bag op Fi t t h e c a n yi n pla ce as s h o w n. Lift the canopy into place so that the screw holes are aligned. Installing the Blades: Secure each blade to a blade iron as shown using the blade nuts, found in the hardware bag, and the blade assembly screws, found in the hardware bag.
1886 Assembling the Light Kit 2 of 3 1 of 3 Light Kit Screw bag Partially install two light kit assembly screws, found in the hardware bag, halfway into the motor housing as shown. It does not matter which two screw holes you choose. bag Light Kit Screw Align the keyhole slots in the top of the light kit assembly with the partially installed assembly screws. Rotate the keyhole slots around the screws and twist counterclockwise. Install the third light kit screw. Tighten all three screws securely.
1886 Preparing the Wall Control 1 Turning off the power Ensure the power is OFF at the outlet box and wall switch location before proceeding with installation. 2 Installing the battery To access the battery compartment, slide the battery door up. 3 Replace the used battery with two AAA batteries when needed. 4 Connect the grounding wire from the wall control to the ground control from the switch box using the provided wire nuts.
1886 Troubleshooting Fan Doesn’t Work Noisy Operation • Make sure power switch is on. • Make sure the blades are properly installed. • Check the circuit breaker to ensure the power is turned on. • Check to see if any of the blades are cracked. If so, replace all of the blades. • Make sure the blades spin freely. Multiple Remote Issues • Check the plug connection in the switch housing. Excessive Wobbling • Make sure the blades are properly installed on the blade iron posts.
1886 Downrod If you need a different downrod length follow these steps: Follow steps 1-5 to remove standard downrod pipe 1 2 3 1 8 10 10 4 5 3 5 9 7 2 4 9 8 6 7 6 Follow steps 6-10 to reassemble with new downrod Pin Pin WARNING FAN FALL HAZARD To prevent SERIOUS INJURY or DEATH: • ALWAYS follow the downrod assembly instructions exactly. • VERIFY the downrod is assembled correctly by firmly pulling on the hanger ball. Here is another view of the downrod assembly unassembled.
