ICR Institutional Commercial Remote For Use with Hunter Controllers Owner’s Manual and Installation Instructions ® ENGLISH/ESPAÑOL OFF ® MODE ON icr
Table of contents...................................................................................... Introduction................................................................................................................................................................... 1 ICR Components............................................................................................................................................................ 2 SmartPort ® Wiring Harness.. ............................
TABLa de contenido.................................................................................... Presentación del Producto............................................................................................................................................ 15 Componentes del ICR................................................................................................................................................... 16 Conexión de Cableado del Programador SmartPort ®. ....................
Introduction................................................................................................ Finally there’s an affordable remote control system designed with the commercial irrigation contractor in mind. Hunter is pleased to introduce the Institutional Commercial Remote (ICR). This rugged remote design offers similar functionality as our SRR remote, but with longer range capability.
ICR Components..............................................................................................
This section will provide a brief overview of some of the components on the ICR. Each item will be discussed in further detail later, however, this section can be helpful in getting acquainted with the different options available. A – Transmitter 1. Transmitter Body – The ICR transmitter is designed to be dirt tolerant and water resistant. B – Receiver 7. Receiver Body – Rugged, water resistant design. 8. Addressing Button – Allows for easy receiver to . transmitter addressing. 9.
SmartPort® Wiring Harness........................................................................ To utilize the ICR remote control system, your controller must be equipped with a SmartPort wiring harness. This wiring harness provides the communication port where the ICR receiver is attached. The SmartPort can be connected to Hunter SRC, Pro-C and ICC controllers. A SmartPort wiring harness is provided with your ICR remote system. The typical SmartPort location is approximately 12" below the controller.
wiring the SmartPort® to hunter controllers............................... SRC Controller SmartPort Installation ICC Controller SmartPort Installation Access the terminal strip area and attach the red wire to the left AC screw slot, attach the white wire to the next AC screw slot and attach the blue wire to the screw slot marked “R”.
Typical Installations................................................................................. Although the ICR Receiver is water resistant, it is recommended that the SmartPort ® connector and Receiver be mounted indoors if it is to be left permanently mounted to the controller. Indoor Installation Outdoor Installation (Temporary Connection of Receiver Only) Controller Receiver Preparing the Transmitter for Use..................................................
Installing the Transmitter Batteries............................................. The ICR transmitter requires 4 AA alkaline batteries. To install the batteries. remove the two screws holding the battery on the back of the transmitter. Drop the batteries into the battery compartment and replace the door. Your transmitter is now ready to operate. Changing the Run Time...............................................................................
Changing the Transmitter Address................................................... Both the ICR Transmitter and Receiver have an “address” that they use when communicating. If the addresses do not match, the Receiver will ignore the transmission. Your ICR comes from the factory with both the transmitter and Receiver address set to 0. You may change the address to any value from 0-127 for added security.
2. Press the Mode button until the word “Max Station” appears on the display. The maximum number of stations will be . blinking at this point. provides the user with the ability to operate programs . (A, B, C). ACC/ACC Decoder Controllers ."9 45"5*0/ 3. Use the or button to increase or decrease the maximum number of stations. Then do not touch any of the buttons for 5 seconds and the display will stop blinking and return back to the active station.
2. After the Receiver starts to beep, release the button. 3. Press either the “ON” or “OFF” button on your transmitter. 4. The Receiver will beep 4 additional times indicating that it has learned the new Transmitter address and will respond only to it from this point on. The ICR system will allow you to remotely turn on and off any station on your Hunter controller with the press of a button. Once on, the station will run for the run time you have designated in the ICR transmitter.
NOTE: The ICR remote can activate any station on the controller whether the controller dial is in the “System Off”, “Run” or “Run/Bypass Sensor” modes. If a sensor device has been wired to the controller, the ICR will not override the sensor for manual operation. Maximizing Operating Range.................................................................. The ICR is designed as an extended range remote that should meet the range requirements for even the largest irrigation systems.
Troubleshooting Guide.............................................................................. PROBLEM CAUSes Solutions Transmitter is blank. Transmitter is Off.. . Battery is dead. Press any button for 1 second.. . Replace battery. Can’t access all the desired stations on the transmitter. Maximum station number is . set wrong. See “Setting the Maximum Station stations Number” SmartPort is not connected properly.. Recheck the SmartPort installation.. Receiver doesn’t beep two times .
Specifications................................................................................................. Operating Specifications Dimensions • Transmitter (w/o antennae): Height: 6.5". Width: 3.25". Depth: 1.25" Receiver (w/o antennae): Height: 6.25". Width: 3". Depth: 1.
Presentación del Producto..................................................................... Por fin hay un sistema de mando a distancia fiable y accesible, diseñado teniendo en mente las necesidades del contratista de la industria de riego comercial. La sociedad Hunter está satisfecha del lanzamiento del ICR, un sistema de mando a distancia. Su diseño de alta resistencia le permite funcionabilidad similar al sistema de mando tipo SRR, pero con una capacidad de mayor distancia.
Componentes del ICR...................................................................................
Esta sección le proporcionará un breve resumen ejecutivo respecto a los componentes del ICR. Cada componente será comentado con mayor detalle posteriormente, asimismo, la presente sección le será útil para familiarizarse con las diferentes opciones disponibles del producto. A – Emisor 1. Cuerpo del Emisor – El Emisor ICR está diseñado para soportar la suciedad y es impermeable. B – Receptor 7. Cuerpo del Receptor – De alta resistencia, con diseño impermeable. 8.
Conexión de Cableado del Programador SmartPort®.................... A fin de poder utilizar el sistema de mando a distancia ICR, su programador Hunter está equipado con un arnés de cableado SmartPort. Dicho cableado de arnés le proporciona una comunicación al puerto a donde se conecta el receptor ICR. El SmartPort puede conectarse a los programadores SRC, Pro-C y al programador ICC. Para su conveniencia, su sistema de mando a distancia ICR incluye un arnés de cableado tipo SmartPort.
Conexión de Cableado del Programador SmartPort®.................... Instalación SmartPort del Programador SRC Module Instalación SmartPort delPower Programador ICC Con acceso al compartimiento de cableado, conecte el cable rojo al primer borneo marcado AC, el blanco al borneo . sugundo marcado AC y el azul al borneo R. Con acceso al compartimiento de cableado, conecte el cable rojo al borneo bajo marcado AC, el blanco al borneo superior marcado AC y el azul al borneo REM.
Instalaciones Típicas............................................................................... Aunque el Receptor ICR es impermeable, se recomienda que, el conector SmartPort ® y su Receptor sean montados bajo techo, si es que se va a dejar montado al programador respectivo en forma permanente. Instalación Interior Instalación Exteriór (Conexion Temporal Únicamente del Receptor) Programador Receptor Preparación del Emisor Antes de su Uso.......................................
Colocación de la Pila del Emisor....................................................... Su emisor ICR funciona con cuatro pilas alcalinas de clase AA. Para instalar las pilas, desplace los dos tornillos que sujetan el compartimiento posterior del emisor. Introduzca las pilas en dicho compartimiento e instale nuevamente la tapa posterior. Concluyendo lo anterior, su emisor está listo para operar. Cambio del Tiempo DEL CICLO de Riego...............................................
Modificación de la Dirección del Emisor....................................... El emisor y el receptor ICR poseen una “dirección” que utilizan para comunicarse entre sí. Cuando ambas direcciones no corresponden, el receptor ignora la transmisión. A la salida de fábrica, las dos direcciones del sistema de mando a distancia ICR están programadas a 0. Puede dar a la dirección un valor comprendido entre 0 y 127 para aumentar la seguridad del sistema.
estación activa. 2. Presione la tecla “Mode”, hasta que aparezcan las palabras “Max. Station” en la pantalla. A continuación aparece en la ."9 45"5*0/ pantalla, en forma intermitente, el número máximo de estaciones. Señalamos que, si se esperan más de 5 segundos sin solicitar ninguna tecla, el emisor visualiza de nuevo la estación activa. 3. Utilizar las teclas y para incrementar o reducir, el número máximo de estaciones.
Modificación de la Dirección del Receptor 2. Soltar el botón en cuanto se oiga el primer bip. 1. Mantener hundida la única tecla situada sobre la cara delantera del receptor mientras que se conecta a un conjunto de cables bajo tensión de un SmartPort ® (el programador bajo tensión). Cuanto esto sucede, el Receptor emite cuatro bips acústicos. 3. Pulsar la tecla “ON” o la tecla “OFF” de su emisor. 4.
acústicos. El sistema ICR ha sido diseñado para poner una sola estación en marcha cada vez. Por consiguiente, si se pone en marcha una estación cuando ora está ya funcionando, esta última se parará automáticamente. 6. Si uno de los programas (A, B, C o desde el P1 al P18) se selecciona, todas las estaciones en el programa seleccionada arrancan en forma secuencial por el ciclo de riego programado por el programador.
Guía Para Solucionar Problemas.......................................................... 26 Problema Causas Soluciones El Emisor está en blanco. El Transmisor está apagado.. . La pila está descargada. Presione cualquier tecla por 1 segundo.. . Reemplace la pila. No se pueden accesar todas las estaciones deseadas el en Emisor. El número máximo de estaciones es incorrecto. Vea “Modificación del Número Máximo de Estaciones”. El Receptor no emite 2 bips acústicos cuando se conecta al SmartPort®.
Datos Técnicos................................................................................................ Especificaciones de Operación Dimensiones • Emisor (sin antena): Altura: 16.5 cm. Ancho: 8.26 cm. Profundidad: 3.17 cm Emisor (sin antena): Altura: 15.87 cm. Ancho: 7.6 cm. Profundidad: 3.
FCC Compliance Notice................................................................................ This device does not require an FCC License. The ICR Receiver complies with the limits of Part 15 of the FCC Rules. The Transmitter complies with Part 95 Subpart E of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a commercial environment. Este sistema no requiere de ninguna licencia de la FCC.