Product Manual
Table Of Contents
- Symbols
- Contents
- Dear customer!
- Note the following before starting:
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Cutting equipment
- Fitting the loop handle
- Fitting the trimmer head
- Fitting the trimmer guard and trimmer head
- Fuel safety
- Fuel
- Fueling
- Check before starting
- Starting and stopping
- General working instructions
- Carburetor
- Muffler
- Cooling system
- Spark plug
- Air filter
- Maintenance schedule
- Technical data
- YOUR WARRANTY RIGHTS AND OBLIGATIONS
- MANUFACTURER¢S WARRANTY COVERAGE
- OWNER¢S WARRANTY RESPONSIBILITIES
- WARRANTY COMMENCEMENT DATE
- LENGTH OF COVERAGE
- WHAT IS COVERED
- EMISSION WARRANTY PARTS LIST
- WHAT IS NOT COVERED
- HOW TO FILE A CLAIM
- WHERE TO GET WARRANTY SERVICE
- MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS
- MAINTENANCE STATEMENT
- Symboles
- Sommaire
- Cher client,
- Contrôler les points suivants avant la mise en marche:
- Important!
- Équipement de protection personnelle
- Équipement de sécurité de la machine
- Équipement de coupe
- Montage de la poignée en boucle
- Montage de la tête de désherbage
- Montage de la protection de la tête et de la tête de désherbage
- Sécurité carburant
- Carburant
- Remplissage de carburant
- Contrôles avant la mise en marche
- Démarrage et arrêt
- Méthodes de travail
- Carburateur
- Silencieux
- Système de refroidissement
- Bougie
- Filtre à air
- Schéma d’entretien
- Caractéristiques techniques
- VOS DROITS ET OBLIGATIONS EN GARANTIE
- GARANTIE DU FABRICANT
- CHARGES DE LA GARANTIE DE L’UTILISATEUR
- DATE D’ENTRÉE EN VIGUEUR DE LA GARANTIE
- DURÉE DE LA GARANTIE
- CE QUI EST COUVERT PAR LA GARANTIE
- LISTE DES PIÈCES GARANTIE ÉMISSIONS
- CE QUI N’EST PAS COUVERT PAR LA GARANTIE
- DEMANDE D’INDEMNITÉ
- SERVICE APRÈS-VENTE
- ENTRETIEN, REMPLACEMENT ET RÉPARATION DES PIÈCES DU SYSTÈME DE LUTTE CONTRE LES ÉMISSIONS
- DÉCLARATION D’ENTRETIEN
- Símbolos
- Índice
- Apreciado cliente:
- Antes de arrancar, observe lo siguiente:
- Importante
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Equipo de corte
- Montaje del mango de tipo cerrado
- Montaje del cabezal de corte
- Montaje de la protección de la recortadora y el cabezal de corte
- Seguridad en el uso del combustible
- Carburante
- Repostaje
- Control antes de arrancar
- Arranque y parada
- Instrucciones generales de trabajo
- Carburador
- Silenciador
- Sistema refrigerante
- Bujía
- Filtro de aire
- Programa de mantenimiento
- Datos técnicos
- SUS DERECHOS Y OBLIGACIONES DE GARANTIA
- ALCANCE DE LA GARANTIA DEL FABRICANTE
- RESPONSABILIDADES DE GARANTIA DEL PROPIETARIO
- FECHA DE INICIO DE LA GARANTIA
- DURACION DE LA GARANTIA
- ALCANCE DE LA GARANTIA
- LISTA DE PIEZAS DE LA GARANTÍA DE EMISIONES
- LO QUE NO ABARCA LA GARANTIA
- COMO HACER UNA RECLAMACION
- DONDE RECIBIR SERVICIO DE GARANTIA
- MANTENIMIENTO, SUSTITUCION Y REPARACION DE COMPONENTES RELACIONADOS CON EMISIONES
- DECLARACION DE MANTENIMIENTO
GENERAL SAFETY PRECAUTIONS
10 – English
screen will cause the engine to overheat and may lead to
serious damage.
NOTE!
Make sure that the spark arrestor is screwed in place
correctly.
Cutting equipment
This section describes how to choose and maintain your
cutting equipment in order to:
• Obtain maximum cutting performance.
• Extend the life of cutting equipment.
Trimmer head
• Only use the recommended trimmer heads and
trimmer cords. These have been tested by the
manufacturer to suit a particular engine size. This is
especially important when a fully automatic trimmer
head is used. Only use the recommended cutting
attachment. See the chapter on Technical data.
• Smaller machines generally require small trimmer
heads and vice versa. This is because when clearing
using a cord the engine must throw out the cord
radially from the trimmer head and overcome the
resistance of the grass being cleared.
• The length of the cord is also important. A longer cord
requires greater engine power than a shorter cord of
the same diameter.
• Make sure that the cutter on the trimmer guard is
intact. This is used to cut the cord to the correct length.
• To increase the life of the cord it can be soaked in
water for a couple of days before use. This will make
the cord tougher so that it lasts longer.
!
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.
This also applies at idle speed. Contact
can result in burns to the skin.
Remember the risk of fire!
!
WARNING! The inside of the muffler
contain chemicals that may be
carcinogenic. Avoid contact with these
elements in the event of a damaged
muffler.
!
WARNING! Bear in mind that:
The exhaust fumes from the engine are
hot and may contain sparks which can
start a fire. Never start the machine
indoors or near combustible material!
IMPORTANT!
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
Refer to the instructions for the cutting attachment to
check the correct way to load the cord and the correct
cord diameter.
!
WARNING! Always stop the engine
before doing any work on the cutting
attachment. This continues to rotate even
after the throttle has been released.
Ensure that the cutting attachment has
stopped completely and disconnect the
spark plug cap before you start to work
on it.
!
WARNING! A faulty cutting attachment
may increase the risk of accidents.
IMPORTANT!
Always ensure the trimmer cord is wound tightly and
evenly around the drum, otherwise the machine will
generate harmful vibration.