Product Manual
Table Of Contents
- Symbols
- Contents
- Dear customer!
- Note the following before starting:
- Important
- Personal protective equipment
- Machine¢s safety equipment
- Cutting equipment
- Fitting the loop handle
- Fitting the trimmer head
- Fitting the trimmer guard and trimmer head
- Fuel safety
- Fuel
- Fueling
- Check before starting
- Starting and stopping
- General working instructions
- Carburetor
- Muffler
- Cooling system
- Spark plug
- Air filter
- Maintenance schedule
- Technical data
- YOUR WARRANTY RIGHTS AND OBLIGATIONS
- MANUFACTURER¢S WARRANTY COVERAGE
- OWNER¢S WARRANTY RESPONSIBILITIES
- WARRANTY COMMENCEMENT DATE
- LENGTH OF COVERAGE
- WHAT IS COVERED
- EMISSION WARRANTY PARTS LIST
- WHAT IS NOT COVERED
- HOW TO FILE A CLAIM
- WHERE TO GET WARRANTY SERVICE
- MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS
- MAINTENANCE STATEMENT
- Symboles
- Sommaire
- Cher client,
- Contrôler les points suivants avant la mise en marche:
- Important!
- Équipement de protection personnelle
- Équipement de sécurité de la machine
- Équipement de coupe
- Montage de la poignée en boucle
- Montage de la tête de désherbage
- Montage de la protection de la tête et de la tête de désherbage
- Sécurité carburant
- Carburant
- Remplissage de carburant
- Contrôles avant la mise en marche
- Démarrage et arrêt
- Méthodes de travail
- Carburateur
- Silencieux
- Système de refroidissement
- Bougie
- Filtre à air
- Schéma d’entretien
- Caractéristiques techniques
- VOS DROITS ET OBLIGATIONS EN GARANTIE
- GARANTIE DU FABRICANT
- CHARGES DE LA GARANTIE DE L’UTILISATEUR
- DATE D’ENTRÉE EN VIGUEUR DE LA GARANTIE
- DURÉE DE LA GARANTIE
- CE QUI EST COUVERT PAR LA GARANTIE
- LISTE DES PIÈCES GARANTIE ÉMISSIONS
- CE QUI N’EST PAS COUVERT PAR LA GARANTIE
- DEMANDE D’INDEMNITÉ
- SERVICE APRÈS-VENTE
- ENTRETIEN, REMPLACEMENT ET RÉPARATION DES PIÈCES DU SYSTÈME DE LUTTE CONTRE LES ÉMISSIONS
- DÉCLARATION D’ENTRETIEN
- Símbolos
- Índice
- Apreciado cliente:
- Antes de arrancar, observe lo siguiente:
- Importante
- Equipo de protección personal
- Equipo de seguridad de la máquina
- Equipo de corte
- Montaje del mango de tipo cerrado
- Montaje del cabezal de corte
- Montaje de la protección de la recortadora y el cabezal de corte
- Seguridad en el uso del combustible
- Carburante
- Repostaje
- Control antes de arrancar
- Arranque y parada
- Instrucciones generales de trabajo
- Carburador
- Silenciador
- Sistema refrigerante
- Bujía
- Filtro de aire
- Programa de mantenimiento
- Datos técnicos
- SUS DERECHOS Y OBLIGACIONES DE GARANTIA
- ALCANCE DE LA GARANTIA DEL FABRICANTE
- RESPONSABILIDADES DE GARANTIA DEL PROPIETARIO
- FECHA DE INICIO DE LA GARANTIA
- DURACION DE LA GARANTIA
- ALCANCE DE LA GARANTIA
- LISTA DE PIEZAS DE LA GARANTÍA DE EMISIONES
- LO QUE NO ABARCA LA GARANTIA
- COMO HACER UNA RECLAMACION
- DONDE RECIBIR SERVICIO DE GARANTIA
- MANTENIMIENTO, SUSTITUCION Y REPARACION DE COMPONENTES RELACIONADOS CON EMISIONES
- DECLARACION DE MANTENIMIENTO
MAINTENANCE
18 – English
Carburetor
Your Husqvarna product has been designed and
manufactured to specifications that reduce harmful
emissions.
Adjustment of the idle speed
Before any adjustments are made, make sure that the air
filter is clean and the air filter cover is fitted.
Adjust the idle speed using the idle adjustment screw T, if
it is necessary to readjust. First turn the idle adjustment
screw T clockwise until the cutting attachment starts to
rotate. Then turn the screw counter clockwise until the
cutting attachment stops. The idle speed is correctly
adjusted when the engine will run smoothly in every
position. The idle speed should also be well below the
speed at which the cutting attachment starts to rotate.
Recommended idle speed: See the Technical data
section.
Muffler
CAUTION! Some mufflers are fitted with a catalytic
converter. See chapter on Technical data to see whether
your machine is fitted with a catalytic converter.
The muffler is designed to reduce the noise level and to
direct the exhaust gases away from the operator. The
exhaust gases are hot and can contain sparks, which may
cause fire if directed against dry and combustible
material.
Some mufflers are equipped with a special spark arrestor
screen. If your machine has this type of muffler, you
should clean the screen at least once a week. This is best
done with a wire brush. On mufflers without a catalytic
converter the screen should be cleaned weekly, or
replaced if necessary. On mufflers fitted with a catalytic
converter the screen should be checked, and if necessary
cleaned, monthly.
If the screen is damaged it should be
replaced.
If the screen is frequently blocked, this can be
a sign that the performance of the catalytic converter is
impaired. Contact your dealer to inspect the muffler. A
blocked screen will cause the machine to overheat and
result in damage to the cylinder and piston.
CAUTION! Never use a machine with a defective muffler.
!
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until
it has been correctly adjusted or
repaired.
!
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.
This also applies at idle speed. Contact
can result in burns to the skin.
Remember the risk of fire!