User's manual

12
12. Reattach the temperature monitor (12) in the smoke ring, leading the sensor about 3 cm into the
smoke ring.
13. Installing the cover plate (3). Place the cover plate over the hole (above the combustion chamber,
where the flue ring was just removed) and fasten with the three screws (Torx Bit no. 30).
14. Installing the flue ring (10). Insert the flue ring into the smoke outlet hole in the rear of the stove and
secure it with the three screws. NB: Remember to turn the lambda probe (11) as illustrated in drawing
E1.
15. Reposition the lambda sensor coupling (7) in the wire fastener (9).
16. Fix the two wires by closing the metallic tabs (8) again.
17. Installing the rear plate (1). Place the rear plate on the guide pins; then press it in towards the stove.
Lift the rear plate and press it lightly inwards until it engages with the guide pins. Fasten the two screws
in the middle of the rear plate again.
18. Installing the top plate of the stove (7). Place the top plate on the fittings and secure it with the four
screws (14), two on each side.
19. Installing sides. Put the sides on the guide pins in the bottom plate of the stove and press them in
towards the stove. Lift the sides and press them lightly inwards until they engage with the guide pins.
An accessory top cover is available to cover the hole in the stove top plate if the smoke outlet is connected
at the rear of the stove.
Changing the smoke outlet from top outlet to rear outlet (HWAM 3650/3660 IHS)
(Drawing E)
1. Removing the rear plate (1). Remove the two screws in the middle of the rear plate. Lift the rear
plate and pull it away from the stove so that it disengages from the guide pins on the bottom plate of
the stove. There is a cut-out in the rear plate for the smoke outlet. Break off the plate (6) within this
cut-out to make a hole in the rear plate so there is room for the smoke outlet.
2. Remove the heat shield (2) by lifting it off the stove. The heat shield has a cut-out for the flue duct.
Break off the pre-cut plate (6); the resulting hole fits the flue duct.
3. Removing the cover plate (3). Remove the cover plate on the back of the stove by removing the three
screws (Torx Bit no. 30).
4. Remove the front of the heat storage compartment (4). Loosen the two screws (5) on each side of
the front of the heat storage compartment without removing them. Then pull the front forward.
5. Open the metallic tabs (8) and take the wires out.
6. Pull the lambda sensor coupling (7) free of the wire fastener (9).
7. Remove the temperature monitor (12) from the smoke ring.
8. Removing the flue ring (10). To remove the flue ring at the bottom of the heat storage compartment
(above the combustion chamber), unscrew the three screws. Lift the flue ring off the top of the stove.
9. The temperature gauge (12) and the lambda sensor coupling (7) are pulled out from the left side of
the wood section and pushed in again through the hole in the right-hand side so that the wires are
kept on the left side of the stove when seen from behind.
10. Reattach the temperature monitor (12) in the smoke ring, leading the sensor about 3 cm into the
smoke ring.
11. Installing the flue ring (10). Insert the flue ring into the smoke outlet hole in the rear of the stove and
secure it with the three screws. NB: Remember to turn the lambda probe (11) as illustrated in drawing
E1.
12. Reposition the lambda sensor coupling (7) in the wire fastener (9).
13. Fix the two wires by closing the metallic tabs (8) again.
14. Installing the cover plate (3). Place the cover plate over the hole in the bottom of the heat storage compart
-
ment (where the flue ring was just removed) and fasten with the three screws (Torx Bit no. 30).
15. Installing the rear plate (1). Place the rear plate on the guide pins; then press it in towards the stove.
Lift the rear plate and press it lightly inwards until it engages with the guide pins. Fasten the two screws
in the middle of the rear plate again.