HyperNet FastPrint Multiprotocol Ethernet/Fast Ethernet Print Server Hardware Users Guide Information in this document is subject to change without notice. All rights reserved. All brand names are registered trademarks of their respective companies.
dafür, daß diese Öffnungen nicht abgedeckt werden. 8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte. 9. Die Netzanschlußsteckdose muß aus Gründen der elektrischen Sicherheit einen Schutzleiterkontakt haben. 10. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollete auch nichts auf der Leitung abgestellt werden. 11. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten. 12.
FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications.
External Features ...................................................................................... 2 Port Connectors................................................................................................... 2 Network Cable Connector ................................................................................... 3 DC Power Connector .......................................................................................... 3 LED Indicators ...................................................
vi Index
Index vii
Print Server Features HyperNet Fastprint print servers improve network printing services in three ways: ♦ The HyperNet Fastprint picks up the workload of managing print file traffic to its connected printers. This provides workload relief to your file servers, and allows the file servers' full capacity to be used for file access or other direct services to network users.
Windows NT, Windows 95/98, Windows for Workgroups, Microsoft LAN Manager, IBM LAN Server ♦ AppleTalk MacOS EtherTalk Windows-based setup and administration software, EtherP Admin, is supplied with the HyperNet Fastprint, making configuration and management quick and easy. The HyperNet Fastprint also supports configuration and management via the telnet protocol for networks without Windowscompatible machines.
Network Cable Connector The HyperNet Fastprint’s right side panel features an RJ-45 connector for connection to 10Base-T Ethernet cabling or 100Base-TX Fast Ethernet cabling (which should be Category 5 twisted-pair cable). The port supports the NWay protocol, allowing the print server to automatically detect or negotiate the transmission speed of the network. DC Power Connector The DC power input connector is located on the HyperNet Fastprint’s right side panel and is labeled DC 12V.
♦ Power/Tx ◊ Steady or flashing green confirms that the HyperNet Fastprint is powered on. ◊ The indicator blinks off briefly to indicate that the HyperNet Fastprint is transmitting to the network. ♦ Link/Rx ◊ Steady or flashing green confirms that the HyperNet Fastprint has a good connection to the Ethernet or Fast Ethernet network. ◊ The indicator blinks off briefly to indicate that the HyperNet Fastprint is receiving from the network.
Server Carefully remove all items from the package. In addition to this Hardware User’s Guide, be certain that you have: ♦ One HyperNet Fastprint print server ♦ One DC power adapter suitable for your country’s electric power ♦ Two EtherP Admin software diskettes ♦ One Print Server Administration User’s Guide ♦ Fasteners for optional wall-mounting If any item is missing, or if you find any damage or mismatch, promptly contact your dealer for assistance.
4. Connect the HyperNet Fastprint to the network, using the RJ-45 (10Base-T/100Base-TX) connector on the print server’s side panel. 5. While each printer is powered off, connect its tested and confirmed port to a like printer port of the HyperNet Fastprint. If you are connecting fewer than three printers, then keep in mind that parallelport connections are preferred for high-performance printers. 6. Switch on each connected printer. 7.
contact your dealer for correction of the faulty unit.
To mount the HyperNet Fastprint with the front panel facing up (and the printer port connectors facing down), set the two mounting screws at the lower-left and upper-right corners of a rectangle as shown below (actual size): 110 mm 4 5/16 in 70 mm 2 3/4 in When setting the screws into the wall or partition, leave about 3 mm (1/8 in) between the head of each screw and the wall surface. Then place the HyperNet Fastprint so that the mounting sockets on the bottom of its case fit over the two screws.
Index 9
Ports: Bi-directional 25-pin parallel ports × 2, 9-pin DTE serial port × 1 Parallel Port Bi-directional Communication: Hewlett-Packard PJL (Printer Job Language) supported Network Connection Network Standards: IEEE 802.3 10Base-T Ethernet, IEEE 802.3u 100BASE-TX Fast Ethernet Network Data Transfer Rate: 10/100Mbps Network Connector: RJ-45 connector for 10Base-T or 100BASE-TX unshielded twisted pair connection; NWay automatic speed negotiation supported. Network Protocols Ethernet Frame Types: 802.2, 802.
Power Supply: External power supply providing 12VDC/ 500mA Dimensions: 190mm × 116.8mm × 30.9mm Weight: approx. 360g Operating Temperature: 0 to 50°C Storage Temperature: -10 to 50°C Humidity: 10% to 90% non-condensing Emissions: FCC Class A, CISPR 22 Class A, VCCI Class 1, AS/NZS 3548:1995 Class A Safety: UL (UL 1950), CSA (CSA950), TUV/GS (EN60950) B Port Pinouts This appendix shows the pinouts of the HyperNet Fastprint parallel and serial printer ports.
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18-25 2 3 4 5 6 7 8 9 10 11 12 13 14 32 31 36 16, 17, 19-30 Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 Data 8 nAck Busy PError Select nAutoFd nFault nInit nSelectIn Ground Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Bi-directional Printer Printer Printer Printer Host Printer Host Host Serial Port The table below shows the pinout of the print server’s 9-pin RS-232 serial port.
Index 13
does not include service to repair damage resulting from accident, disaster, misuse, abuse or non-Hypertec modification of the product. Additional components installed by the dealer or end user are not covered by this warranty. Apart from the above, no warranty is expressed or implied, including warranty of merchantability or warranty of fitness for use for a particular purpose. The liability of Hypertec is limited to the repair or replacement of the product with a functionally equivalent or better product.
LPT1 ........................................................... 3 self-test........................................................ 8 LPT1 LED............................................... 5, 9 telnet ........................................................... 2 LPT2 ........................................................... 3 wall mounting ........................................... 10 LPT2 LED............................................... 5, 9 wall-mounting .....................................
