HyperNet Token Ring PC Card HYNTR70002 User Guide Information in this document is subject to change without notice. All rights reserved. All brand names are registered trademarks of their respective companies.
European Community (EC) Electromagnetic Compatibility Directive. This equipment had been tested and found to comply with the protection requirements of European Emission Standard EN55022 and the Generic European Immunity Standard EN50082-1. This equipment is designed to operate in a domestic environment and as such is tested to the EN5022 ITE domestic emissions limit.
PCMCIA compatibility and Plug and Play features are assured with full support of all major Card and Socket Services vendors. Compatibility with all major Network Operating Systems is guaranteed by Hypertec's wide range of well tested NOS drivers. Additionally, Hypertec’s Token Ring PC adapter is compatible with software packages such as the IBM PC Network Program, the Advanced Program to Program Communication (APPC) package, and the Multi Protocol Transport Services (MPTS) package.
If you do not have each of these items, contact your supplier before proceeding further Static Electricity Warning Static electricity is accumulated naturally in the human body, and can be discharged through electrical components by touching them. This shock can potentially cause permanent internal damage to the component.
adapter is a Type II PCMCIA card, which is compatible with any Type II PCMCIA slot. If your computer has more than one slot, you may insert the adapter in any of them. The Token Ring software automatically determines into which slot the card is inserted. Gently insert the card into the PCMCIA slot, pushing it until it sits firmly in place. The card will only fit one way; care must be taken not to force it. If it does not register smoothly, withdraw it and check that it is correctly aligned.
Socket services. When Card and Socket Services are present, the drivers will automatically configure themselves to work with it. When Card and Socket services are not detected, the drivers will automatically select to work with direct enablers. Hypertec's PCMCIA Support Driver The Hypertec PCMCIA Support Driver (SPTDRV) either replaces or works in conjunction with the Card & Socket Services software.
in “Custom” mode. These procedures are the same as for modifying configuration parameters and running diagnostic tests after the initial installation, as described in Section 4, “Operation”. Windows Installation To install the adapter using Windows: 1. Start Windows. 2. Insert the SPT software diskette into the PC diskette drive. 3. From the Program Manager, select the File menu. (For Windows 95, select the Start menu) 4. Select Run... 5. Type A:\SETUP and select OK. 6.
screen indicates the tests status. Running Tests 1. While the tests run, the Close button on this screen changes to a Stop button. To stop the tests, press Stop. 2. If a test failed, a message appears next to the failed status, and the tests stop running. To view troubleshooting information for a failed test, press Details. 3. The Wizard utility gives the option of returning to the Hardware Setup screen and redefining parameters. 4.
The following sections present instructions for installing specific Network Operating System drivers. For other Network Operating Systems, please follow the on-screen instructions or print the appropriate documentation file from the DOCS sub-directory on the SPT software diskette. Novell 1. Select the NetWare version of your choice and press Install. A screen appears which prompts you to enter the destination directory. 2.
. 11. Windows for Workgroups will now copy the appropriate drivers to the hard disk and modify the config.sys, autoexec.bat,system.ini and protocol.ini files. When installation is complete, select OK and reboot. Installation is now complete. Windows 95 Hyptertec's Token Ring Software diskette contains files and is structured especially to support Windows 95 Plug & Play installation. To install the Hypertec Token Ring adapter in Windows 95 operating system: 1.
7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. To setup the software, select Configure. From the Configure menu, select LAN adapters and Protocols. From the menu, select Configure. Select Other Adapters. Insert the Hypertec Token Ring PCMCIA software diskette into the diskette drive and type A:\IBMCOM.OS2. Press Enter. From the list of adapters, select the Hypertec PCMCIA Token Ring adapter. Press Add. Add the necessary protocols suited for your network, and select OK. Select Close.
Help Access help information. Viewing Configuration Parameters To view system configuration parameters, select System Config from the View menu. The configuration information is grouped into three categories. To view specific information, click on the PCMCIA, System or Network button. Modifying Configuration Parameters To modify PCMCIA configuration parameters, select Configure PCMCIA from the Configure menu. The same Hardware Setup screen which appears during the installation process appears.
Explanation Possible problem in the card configuration. Recommended Actions Check that the PCMCIA Adapter card is inserted into the PCMCIA slot. If a memory manager is loaded, make sure it excludes the memory range used by the Token Ring PCMCIA Card. If the SOCKET keyword is present in the command line of the support driver (SPTDRV) in the config.sys file, then check that it points to the correct slot or remove the keyword. Try to load the driver when no memory manager is present.
Explanation As above Recommended Actions As above Network Driver Troubleshooting When an error message is received from one of the Network Operating System (NOS) drivers, first check the following: The SPTDRV driver is loaded in the config.sys before the Network Operating System (NOS) driver. The Token Ring PCMCIA card is properly inserted into the slot and that all the cables are connected properly.
adapter in the slot ready for you to use next time. To remove the STP connection from the card, gently squeeze the plastic clips located on the side of the connector and separate it from the card. Never disconnect the HyperNet PC Card by pulling on the cable. If at any time during installation you experience difficulties, please contact Hypertec Technical Support on +44 1488 686844 (01488 686844 in the UK).
Direct Enablers Weight: 2.1 oz, 62 gr. (including STP connector) PCMCIA Card Size: Length - 3.37"(85 mm) Width - 2.13"(54 mm) Thickness - 0.197"(5 mm) Power Consumption: 160mA (active), 40mA (sleep) Operating Temperature: 0°- 50°C Operating Humidity: 0% - 90% non-condensing Certifications: FCC Part 15, Subpart B class A CE Token Ring Protocols: IEEE 802.2 and 802.
Filter (TRMF).
or non-Hypertec modification of the product. Additional components installed by the dealer or end user are not covered by this warranty. Apart from the above, no warranty is expressed or implied, including warranty of merchantability or warranty of fitness for use for a particular purpose. The liability of Hypertec is limited to the repair or replacement of the product with a functionally equivalent or better product.
