Installation Instructions

ManualsBrandsICC ManualsAccessories4-Post Adjustable Distribution Rack

4-Post Adjustable Distribution Rack

INSTALLATION INSTRUCTIONS

CUSTOMER CARE / TECHNICAL SUPPORT • CSR@ICC.COM / 888-ASK-4-ICC (275-4422)

Premium

Products

I Proven

Performance

I Competitive

Prices

4-Post Adjustable Distribution Rack

Ensure all parts and hardware is included in

the packaging box. Box should contain:

ICCMSR4P84

A. (2) Top Angles

B. (2) Base Angles

C. (4) Side Channels

D. (4) Extension Channels

E. (8) Extension Brackets

Product Specifications

Material:

A. Side Rails: 6063 T-6 Alum. 3" C-Channels

B. Top Angle & Base Angle: 6061 T-6 Alum.

C. Extension Bracket and Extension Channel: 12GA CRS

Thread:

A.#12-24 UNC Per ANSI/EIA Spacing

2. Determine the desired width of the rack. NOTE: The rack width is adjustable from 27" min. to 32" max.

Fig. 1

3. Lay (2) Side Channels on a flat surface with the open channels facing inward. Place one (1) top angle across the front of the Side Channels. Install

two (2) 3/8-16 bolts, lock washers, and nuts to secure the top angle with the front of the Side Channels. Place (4) Extension Brackets on the rear side

of the channel. Secure the Extension Brackets to the rear of the Side Channels with (2) 3/8-16 bolts, lock washers, and nuts. Place one Base Angle

across the bottom end of the side rails. Secure the Base Angels to the Side Channels with (4) 3/8-16 bolts, lock washers, and nuts. NOTE: HAND

TIGHTEN ALL NUTS ONLY.

Repeat the process to assemble the rear side.

Recommended Hardware (sold separately)

ICCMSRFLKT -Rack Floor Mount Kit, Concrete

ICCACSS01BK -#12-24 X 5/8 Pilot Point Rack Screw

F. (24) 3/8-16 Bolts

G. (24) 3/8 Lock Washers

H. (24) 3/8-16 Nuts

I. (16) 1/4-20 Carriage Bolts

J. (16) 1/4-20 Lock Washers

K. (16) 1/4-20 Nuts

Fig. 1

Summary of content (2 pages)

PAGE 1
4-Post Adjustable Distribution Rack I N S T A L L A T I O N I N S T R U C T I O N S E 4-Post Adjustable Distribution Rack D ICCMSR4P84 A Ensure all parts and hardware is included in the packaging box. Box should contain: A. (2) Top Angles B. (2) Base Angles C. (4) Side Channels D. (4) Extension Channels E. (8) Extension Brackets F. (24) 3/8-16 Bolts G. (24) 3/8 Lock Washers H. (24) 3/8-16 Nuts I. (16) 1/4-20 Carriage Bolts J. (16) 1/4-20 Lock Washers K.
PAGE 2
ASSEMBLY INSTRUCTIONS 27.00 32.00 4. Install the (4) Extension Channels according to the chosen width of the rack. Use the (16) 1/4-20 Carriage Bolts, lock washers, and nuts to secure the Extension Channels to the Extension Brackets. NOTE: The location of the carriage bolts will depend on the distance between the front and rear side channels. Hand tighten all nuts only. 84.00 5. Stand the assembly up and check for squareness. Make sure the Base is level and will rest on a flat surface. 6.