PRODUCT MANUAL FOR MODEL IOD16022 AND IOD22030 COUNTER TOP DISPENSER Part Number 9081286-01 Print Date 7/01P
IOD16022 IOD22030 Introduction To the owner or user: This product manual is a source of information about the installation, start up, cleaning, maintenance and repair of the product. The IOD16022 and IOD22030 are ice only counter top dispensers designed to use 22 inch wide and 30 inch wide respectfully Ice-O-Matic cubed ice machines as the source of ice. Ice from the cuber falls into the insulated bin where it is stored until needed.
IOD16022 IOD22030 Specifications Limitations: Must meet the same limitations as the cuber installed on top of it: 50° F. air minimum 100° F. air maximum Must be installed indoors. Must allow at least 6 inch clearance at the rear and both sides when using an air cooled ice machine. Must allow space for the utility connection at the back. Must have a drain.
IOD16022 IOD22030 Specifications Front View IOD16022 Front View IOD22030 Ice-O-Matic ice machines are not designed for outdoor installations. Machine requires voltage indicated on rating nameplate. Failures caused by improper voltage are not considered factory defects. Extended periods of operation at temperatures exceeding limitations constitutes misuse under the terms of the Ice-O-Matic Manufacture’s Limited Warranty, resulting in a loss of warranty coverage.
IOD16022 IOD22030 Installation: General Equipment Description The IOD16022 and IOD22030 are counter top mounted ice only dispensers. These units are designed to dispense cube ice only and have ice storage capacities of 160 lb. and 220 lb. respectively. Site Preparation The site chosen for the dispenser must be capable of supporting the dispenser with a full bin of ice plus all other loads being placed on the surface supporting the dispenser.
IOD16022 IOD22030 Installation: General Drain Line Installation (Dispenser) Connect a ¾” ID flexible drain hose to the drain nipple located under the ice storage bin. Clamp the hose in place and insulate the hose to prevent condensation. Connect a ¾” ID flexible drain hose to the drain tube at the back of the drain pan. Clamp the drain hose in place.
IOD16022 IOD22030 Installation: General Final Preparation Install the drain pan on the dispenser by engaging the slots in the metal backplate of the drain pan onto the brackets protruding from the lower left and right hand corners of the dispenser front. Push down on the drain pan to lock it into place. When applicable, seal the drain pan to the counter top. If the dispenser is to be sealed to the counter top, use the sealant recommended in the “Dispenser Installation” section of the instructions.
IOD16022 IOD22030 Installation: General Ice Machine Installation Make sure the counter the dispenser is place on is structurally able to hold the combined weight of the dispenser, ice and ice machine. Remove the dispenser cover. (Retain for future use) Place the appropriate stainless steel KBT adapter onto the top of the dispenser. 22 inch wide ice machine on a 22-inch wide dispenser. Part number KBT2222 22 inch wide ice machine on a 30-inch wide dispenser.
IOD16022 IOD22030 Cleaning and Sanitizing The dispenser must be cleaned and sanitized periodically as prescribed by local health authority or the product supplier, which ever has jurisdiction. Ice-O-Matic recommends the dispenser be cleaned and sanitized at least monthly if not specified by local code requirement. Dispenser Cleaning and Sanitizing Procedures WARNING: When using cleaning fluids or any chemicals, rubber gloves and eye protection should be worn.
IOD16022 IOD22030 Cleaning and Sanitizing Monthly And Initial Start-Up: Sanitize the ice storage system Disconnect power to the dispenser and ice machine. Remove the dispenser front cover plate in front of the ice machine and discard all remaining ice, Mix a solution of 1 ounce of household bleach to 2 gallons of potable water, or: mix a solution of any approved sanitizer, following the directions for mixing and applying that sanitizer.
IOD16022 IOD22030 Service Diagnosis/Electrical Sequence Service Diagnosis PROBLEM PROBABLE CAUSE CORRECTION Will not dispense ice No ice in hopper Fill bin with ice Vend switch does not close Check vend switch, replace if open Drive motor not working Check drive motor, replace if not working Door solenoid will not open door Check/replace door and solenoid Rotor will not turn Check hub of rotor Relay for vend switch does not close during operation Check relays, replace as required Electrical
IOD16022 and IOD2230 Service Parts IOD16022 IOD22030 This parts list contains the service parts available for the IOD16022 and IOS22030 ice only dispenser. Check the model number on the data plate and refer to the correct column listing for the specific dispenser. These two models share many common components but also have components that are model specific. Check carefully that the correct part is identified and ordered.
IOD16022 and IOD2230 Service Parts Cabinet Page 12 IOD16022 IOD22030
IOD16022 IOD22030 IOD16022 and IOD2230 Service Parts Cabinet Item Number IOD16022 Part Number IOD22030 Part Number Description 1 30064502 30064512 Black Lid 2 30074312 30074312 Side Panel Extension 3 3012236901 3012236901 Gearmotor Assembly 4 N/A N/A Drain Hose 5 2066110000 2066110000 Leg Kit 6 30074311 30074311 Side Panel Extension 7 1117390000 1117390000 Switch, Lock and Key 8 3002304001 3002304001 Rotor 9 3A34760001 3A34760001 Hub Assembly 10 3A34810001 3A348100
IOD16022 and IOD2230 Service Parts Cabinet Front Page 14 IOD16022 IOD22030
IOD16022 IOD22030 IOD16022 and IOD2230 Service Parts Cabinet Front Item Number IOD16022 Part Number IOD22030 Part Number Description 1 30064206 30064226 Cover, Merch. Black-Lever 30064218 30064238 Cover, Merch. Black-Push Button 30069901 30069901 Screws For Cover 2 3015075218 3015075418 Merch.
IOD16022 and IOD2230 Service Parts Control Box Page 16 IOD16022 IOD22030
IOD16022 IOD22030 IOD16022 and IOD2230 Service Parts Control Box Item Number IOD16022 Part Number IOD22030 Part Number Description 1 3000480001 3000480001 Relay 2 1193210500 1193210500 Transformer 3 2021610000 2021610000 Starter Socket 4 3012238501 3012238501 Bulb Holder 5 30073510 30073530 Control Box Cover 6 3012237701 3012237702 Fluorescent Tube 7 3002306701 3002306701 Cover 8 3013088201 3013088201 Rubber Mounts 9 3A32683003 3A32683003 Solenoid 10 3013059500 301
IOD16022 and IOD2230 Service Parts Ice Door and Solenoid Assembly Page 18 IOD16022 IOD22030
IOD16022 IOD22030 IOD16022 and IOD2230 Service Parts Ice Door And Solenoid Assembly Item Number IOD16022 Part Number IOD22030 Part Number Description 1 3A34801001 3A34801001 Ice Door 2 1061400000 1061400000 Cotter Pin (6 Req.
IOD16022 and IOD2230 Wiring Diagrams Page 20 IOD16022 IOD22030
IOD16022 and IOD2230 Wiring Diagrams Page 21 IOD16022 IOD22030
