Datasheet

LF1B-N LED Illumination Units
Dimensions
A
C
D
（
B
）
35.0
6.0
R2.1
4.2
2.5
9.0
14.0 27.5
16.0
35.0
Internal Circuit
Fuse
LED
Brown (+)
Blue (–)
Part Number A B C
LF1B-NA 134 64 123
LF1B-NB 210 140 199
LF1B-NC 330 260 319
LF1B-ND 580 510 569
LF1B-NE 830 760 819
LF1B-NF 1,080 1,010 1,069
Part Number D
LF1B-N∗-2∗-1M
1,000
LF1B-N∗-2∗-3M
3,000
All dimensions in mm.
Safety Precautions
Instructions
LED modules may vary in illumination colors and illuminance. •
Before designing equipment and powering up illumination units, •
confirm the specifications described in the instruction sheet.
Apply voltage within the rated value, otherwise the LED elements •
may be damaged.
The illumination unit is vulnerable to static electricity. Take suf- •
ficient measure for protection against static electricity and voltage
surges.
Make sure that the illumination unit does not fall during transpor- •
tation, installation, and operation, otherwise damage may result.
Do not pull or push the cable of the illumination unit, otherwise •
damage may result. Allow sufficient slack to the cable while wiring.
Do not apply excessive force. Do not leave a damaged illumina- •
tion unit unattended or use a damaged illumination unit.
Ensure the correct operating temperature. Otherwise internal •
temperature rise may result in damage.
Do not use or store in a place subjected to vibration and shock. •
Do not use in the following places: •
∗Exposed to direct sunlight, near heaters, high temperatures
∗ Subject to chemicals, and corrosive gases (Plastic illumination
surface types: Iron powder and oil)
∗Basements, greenhouses, or other humid places
∗ Cold storage warehouses (make sure that no freezing occurs)
Do not loosen screws, otherwise the protection characteristics will •
be impaired.
To clean the cover, use a soft cloth with water or neutral deter- •
gent. Do not use solvents such as thinners, benzene, or alkaline,
otherwise discoloration, deterioration, or decrease in strength may
occur.
The edge of the cable sheath is not waterproof construction. Wa- •
ter may invade the LF1B in a capillary action when water splashes
directly onto the cable sheath.
Do not disassemble, repair, or modify the LF1B-N. Otherwise •
electric shock, fire, or malfunction may occur.
Turn off power before wiring. Make sure of correct wiring, other- •
wise electric shock or damage may result.
Do not stare directly into the LF1B-N unit while it is lit, and do not •
project the light to other people, otherwise eyes may be injured.
The LF1B-N is a general-purpose industrial electric device. Do •
not use for electronic equipment which may damage the human
body or threaten life in case a malfunction or failure occurs.
7-31, Nishi-Miyahara 1-Chome, Yodogawa-ku, Osaka 532-8550, Japan
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
Specifications and other descriptions in this catalog are subject to change without notice.
Cat. No. EP1398-0 JUNE 2011 PDF
IDEC ELECTRONICS LIMITED
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
IDEC ELEKTROTECHNIK GmbH
Tel: [phone] - 0, Fax: [phone] - 24
E-mail: [e-mail]
IDEC (SHANGHAI) CORPORATION
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
IDEC (BEIJING) CORPORATION
Tel: [phone], Fax: [phone]
IDEC (SHENZHEN) CORPORATION
Tel: [phone], Fax: [phone]
IDEC IZUMI (H.K.) CO., LTD.
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
IDEC TAIWAN CORPORATION
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
IDEC IZUMI ASIA PTE. LTD.
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
www.idec.com
IDEC CORPORATION (USA)
Tel: [phone] / (800) 262-IDEC (4332)
Fax: [phone]
E-mail: [e-mail]
IDEC CANADA LIMITED
Tel: [phone], Toll Free: [phone]
Fax: [phone]
E-mail: [e-mail]
IDEC AUSTRALIA PTY. LTD.
Tel: [phone], Toll Free: 1800-68-4332
Fax: [phone]
E-mail: [e-mail]
(110610)