Installation guide

IMPORTANT:IfthisproductisconnectedtoaGFCI(GroundFault
CircuitInterrupter)protectedoutlet,nuisancetrippingofthe
powersupplymayoccur,resultinginlossofcooling.Foodquality
andflavormaybeaffected.Ifnuisancetrippinghasoccurred,and
iftheconditionofthefoodappearspoor,disposeofit.
NOTE:Beforeperforminganytypeofinstallation,cleaning,or
removingalightbulb,turnthecontrol(Thermostat,Refrigeratoror
FreezerControldependingonthemodel)toOFFandthen
disconnecttherefrigeratorfromtheelectricalsource.Whenyou
arefinished,reconnecttherefrigeratortotheelectricalsourceand
resetthecontrol(Thermostat,RefrigeratororFreezerControl
dependingonthemodel)tothedesiredsetting.
V_ii:_i::::;ili:,ib_¸__!il;L_ii!i_:::ii!l,,::::::i_,!!i,i,'ii:iii_i_,i:::!iLiiii_,i:;!!!!_,!i_'_ii_i!_f_ili;
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
TOOLS NEEDED:
• Flat-blade screwdriver • %" Drill bit
• 7A6"and 1/2"Open-end or two • Hand drill or electric drill
adjustable wrenches (properly grounded)
• 1/4"nut driver
NOTE: Your refrigerator dealer has a kit available with a %"
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or 3/16"
(4.76 mm) saddle valve which reduces water flow and clogs more
easily.
IMPORTANT:
• All installations must meet local plumbing code requirements.
• Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures will remain
above freezing.
Water Pressure
A cold water supply with water pressure of between 30 and
120 psi (207 - 827 kPa) is required to operate the water dispenser
and ice maker. If you have questions about your water pressure,
call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 - 827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 - 414 kPa):
• Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
• Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
• If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See "Water Filtration
System" in the Use & Care Guide.
If you have questions about your water pressure, call a licensed,
qualified plumber.
INSTALLATIONINSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install
refrigerator.
Failure to do so can result in back or other injury.
Remove the Packaging
Properly dispose of packaging. Do not use sharp instruments,
rubbing alcohol, flammable fluids, or abrasive cleaners to remove
tape or glue. These products can damage the surface of your
refrigerator.
IMPORTANT:
• Use 3/8"socket wrench to remove skids.
• All four leveling legs must contact the floor to support and
stabilize the full weight of the refrigerator.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator
for cleaning or service, be sure to protect the floor=
Always pull the refrigerator straight out when moving it=
Do not wiggle or "walk" the refrigerator when trying to move
it, as floor damage could occur=
Clean Before Using
After you remove all of the package materials, clean the inside of
your refrigerator before using it. See the cleaning instructions in
the Use & Care Guide.
_mportant information to know about glass she_ves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping=
For your protection, tempered glass is designed to shatter
into many small, pebbIe-size pieces= This is normal= GIass
shelves and covers are heavy= Use special care when
removing them to avoid impact from dropping.