User's Manual

70-M USER’S MANUAL
70-M V1.1 (05/07) 120009-0D.pdf IKUSI se reserva el derecho de modificar esta información sin previo aviso. 14
70-M V1.1 (05/07) 120009-0D.pdf IKUSI reserves the right to modify this information without prior notification.
6.3.- BASE CHANNEL CHANGE (TRANSMITTER MODELS:T70MG10;T70MH3D;T70MH3;T70MH2)
T70MG10 TRANSMITTER MODEL
+
BASE CHANNEL CHANGE MODE (Press “5” and “10” functions
simultaneously) -> Wait until the orange LED lights on continuously.
3) The current base channel information is displayed: Number of red pulses = Number of units of the
channel; Number of green pulses = Number in units of ten of the channel.
4) Once the orange LED lights continuously, proceed to change the base channel
Press function “1”, as many times as the number of units of ten of the new base channel.
Note: To programme channels from 1 to 9, do not press this function –equivalent to 0 value--
Press function “2”
,
as man
y
times as the number of units of the new base channel.
6) Updating and sending the new base channel data to the receiver (orange LED blinking).
7) Once the new base channel is recorded in the receiver the transmitter switches to stand-by or LOW
CONSUMPTION mode (Orange LED stops blinking ).
5) To validate the new base channel, inmediately, press “10” function.
Remark: If “10” function is not pressed inmediately, the new base channel is updated after a
few seconds.
The new updated base channel value will show with red and green
LED pulses:
Number of red pulses = Number of units of the channel.
Number of green pulses = Number in units of ten of the channel.
2
)
Enterin
g
the base channel chan
g
in
g
mode:
1
)
With the transmitter switched off
,
p
ress “ON/OFF”. Transmitter in stand-b
y
or LOW CONSUMPTION mode.
Note: Press “4” function to leave the process without updating the new base channel.
The transmitter switches to stand-by or LOW CONSUMPTION mode.
T70MH3 and T70MH2 TRANSMITTER MODELS
BASE CHANNEL CHANGE MODE (Press “RIGHT” and “START” functions
simultaneously) -> Wait until the orange LED lights continuously.
3) The current base channel information is displayed: Number of red pulses = Number of units of the
channel; Numberr of green pulses = Number in units of ten of the channel.
4) Once the orange LED lights continuously, proceed to change the base channel
Press function “DOWN”, as many times as the number of units of ten of the new base channel.
Note: To programme channels from 1 to 9, do not press this function –equivalent to 0 value--
Press function “UP”
,
as man
y
times as the number of units of the new base channel.
6) Updating and sending the new base channel data to the receiver (orange LED blinking).
7) Once the new base channel is recorded in the receiver the transmitter switches to stand-by or LOW
CONSUMPTION mode (Orange LED stops blinking ).
5) To validate the new base channel, inmediately, press “START” function.
Remark: If “START” function is not pressed inmediately, the new base channel is updated
after a few seconds.
The new updated base channel value will show with red and green LED pulses:
Number of red pulses = Number of units of the channel.
Number of green pulses = Number in units of ten of the channel.
2
)
Enterin
g
the base channel chan
g
in
g
mode:
1
)
With the transmitter switched off
,
p
ress “ON/STOP”. Transmitter in stand-b
y
or LOW CONSUMPTION
Note: Press “ESC”->T70MH3 model or “RIGHT”->T70MH2 model function to leave
the process without updating the new base channel. The transmitter switches to stand-by
or LOW CONSUMPTION mode.
+
“ESC”
“RIGHT”