User's Manual

70-M USER’S MANUAL
70-M V1.1 (05/07) 120009-0D.pdf IKUSI se reserva el derecho de modificar esta información sin previo aviso. 16
70-M V1.1 (05/07) 120009-0D.pdf IKUSI reserves the right to modify this information without prior notification.
6.4 ID RELEASE (LIB ID) (TRANSMITTER MODELS:T70MG10;T70MH3D;T70MH3;T70MH2)
2) To enter in LIB ID mode, press simultaneously “4” and “10” functions, until the orange LED lights on.
Enter the receiver’s serial number (see the procedure in Note 1), and then press “10” function to validate.
If the receiver recognises the serial number, the ID code is released. During the release process the LED
blinks in orange colour and the buzzer sounds, indicating that the current ID is beeing released in the
receiver. When finished the LED lights off and the transmitter sets to stand-by or LOW CONSUMPTION
mode.
T70MG10 TRANSMITTER MODEL
A
)
ID release from the current transmitte
r
which has the ownershi
p
of the receiver.
1
)
With the transmitter switched off
,
p
ress “ON/OFF”. Transmitter in stand-b
y
or LOW CONSUMPTION mode.
2
)
To enter in LIB ID mode
,
p
ress simultaneousl
y
“4” and “10” functions
,
until the oran
g
e LED li
g
hts on.
3) To execute ID release, press “10” function. During the ID release process the LED blinks in orange
colour and the buzzer sounds, indicating that the current ID is beeing released in the receiver. When
the process has finished the LED lights off and the transmitter sets to satand-by or LOW
CONSUMPTION mode.
+
B
)
ID secure release from a new transmitte
r
which has not the ownershi
p
of the receiver.
1
)
With the transmitter switched off
,
p
ress “ON/OFF”. Transmitter in stand-b
y
or LOW CONSUMPTION mode.
+
Receiver’s serial numbe
r
T70MH3 / T70MH2 / T70MH3D TMTRANSMITTER MODELS
A
)
ID release from the current transmitte
r
which has the ownershi
p
of the receiver.
1
)
With the transmitter switched off
,
p
ress “ON/OFF”. Transmitter in stand-b
y
or LOW CONSUMPTION mode.
2) To enter in LIB ID mode, press simultaneously “UP” and “START” functions,
until the orange LED lights on.
3) To execute ID release, press “START” function. During the ID release process the LED blinks in orange
colour and the buzzer sounds, indicating that the ID is being released in the receiver. When the process
has finished the LED lights off and the transmitter sets to satand-by or LOW CONSUMPTION mode
B
)
ID secure release from a new transmitte
r
which has not the ownershi
p
of the receiver.
1
)
With the transmitter switched off
,
p
ress “ON/OFF”. Transmitter in stand-b
y
or LOW CONSUMPTION mode.
2) To enter in LIB ID mode, press simultaneously “UP” and “START” functions, until the orange LED lights on.
Enter the receiver’s serial number (see the procedure in Note 1), and then press “START” function to validate.
If the receiver recognises the serial number the ID code is released. During the release process the LED blinks in
orange colour and the buzzer sounds, indicating that the current ID is being released in the receiver. When finished
the LED lights off and the transmitter sets to stand-by or LOW CONSUMPTION mode.
+
+
Receiver’s serial number
Note 1: Procedure to enter the receiver’s serial number.
The serial number is inserted in a sequencial way introducing each number, from the left to the right:
- The function number “1” performs the validation from one digit to the following digit (from the left to the right).
- The function number “2” is used to press it as many times as the number, of each digit.
Example: Insert the serial number 01071035 -> remote manufactured on January of 2007, with number 1035.
1st digit (0):press function “2” zero times -> press function “1” to jump to the following digit.
2nd digit (1): pulsar la función “2”, one time -> press function “1” to jump to the following digit.
3rd digit (0): pulsar la función “2” zero times -> press function “1” to jump to the following digit.
4th digit (7): pulsar la función “2” seven times -> press function “1” to jump to the following digit.
5th digit (1): pulsar la función “2” one time -> press function “1” to jump to the following digit.
6th digit (0): pulsar la función “2” zero times -> press function “1” to jump to the following digit.
7th digit (3): pulsar la función “2” three times -> press function “1” to jump to the following digit.
8th digit (5): pulsar la función “2” five times -> press function “1” to jump to the following digit.