X350 MANUAL MORE POWER 350W 15A
X350 specific for Hobby gay’s needs!
New Chager X350 Released iM·OS System (System: iM·OS V2.11) www.imaxrc.com/x350.html www.imaxrc.com/x350.html Touch Scr een c harger Mul ti pl e l a ngua ge s customizatio n Multiple languages customization A whole ne w product definition method A whole new product definition method Touch Screen Operation 4.
iM·OS System www.imaxrc.com/x350.html LiPo Lipo Battery,Single Nominal Voltage: 3.7V,Charge cut-off voltage 4.2V,Discharge cut-off voltage 3.0V LiIon LiIon Battery,Single Nominal Voltage: 3.6V,Charge cut-off voltage 4.1V,Discharge cut-off voltage 2.5V Balance Lipo balance charge use CC-CV charging way. The charger will balance the battery voltage when charging, this only for LiPo battery. Please connecting the balance port when charging and discharging. Support 2-6 cells. Charge Use CC-CV charging way.
X350 Fundamental Function All in one。 www.imaxrc.com/x350.html The socket name match with the plug,please make sure the right port before using All in one. Fuse Fuse Safety Current : 30A Touch Screen Dean JST-XH Balance port Glow socket IBP No:201230484397.8 DC IN IBP USB No:201230484397.8 Tamiya No:201230484398.2 JST/BEC EC3 XT60 JR/FU IBP No:201230484396.3 Avoiding the switch wires making the balance cable and high current cable into one. It ran perfectly on the very first try.
1 Preparing Connecting Using www.imaxrc.com/x350.
X350 is a professional RC model battery charger,please view the manual before using. If Extras Including you are a fresh man please read this entire operating manual completely before using. X350 included with 1pcs adapter board,1pcs connect cable and 1 pcs manual. 【Warning: 】The warning of charger operation and disclaimer, Please read and abide by the following terms before operation. 1. This is a sophisticated hobby product.
Connecting X350 2: Connecting the adapter board into the X350 IBP port. Please follow the below steps connecting: 1: Please connecting the cable to the adapter port and the X350 DC IN port, and then plug the adapter power cord into the socket. 【NOTE】 USB support 5V 2.1A charging voltage,and also use for iPad / iPod / iPhone / HTC and other intelligent electronic equipment. Both the USB and All in one get charged simultaneously.
3: Please make sure the port connect with battery(Other ports are same as it). 4: Sarting X350 startup X350 to enter the main interface ( Image 1 ). Copyright © iMaxRC Corporation 2012 Image 1 Showing“Warning and Disclaimer” 2 seconds and will know the copyright and security information ( Image 2 ).
Sample 1:Choose a set of LiPo battery charging,please follow the below steps: Step 1: Touch Type( Image 5 ) Enter into the “Type interface”, and then Touch :LiPo ( Image 6 ) will Enter into main interface go on the next step. Image 3 【NOTE】 Please read Disclaimer before doing anything. 6: Enter into main interface after accepting( Image 4 ). Start to charge and discharge according to the different battery. Image 5 Action Bar Information Bar Image 4 Image 6 【NOTE】 Information bar can not get touched.
Step 2: Touch ‘Mode’ icon( Image 7 ) to enter into Mode interface. Please choose Step 3: Touch Cells icon ( Image 9 ) to enter into Cells interface. Please set battery packs battery charge mode ( Image 8 ) and go back to main interface to continue setting. by sliding ( Image 10 ). Touch OK to go back to main interface and continue setting. Image 7 Image 9 Image 8 Image 10 【Note】 There are six charge/discharge modes in Mode interface( Image 8 ), see iM.OS System function for further details.
Step 4: Touch Current icon ( Image 11 ) to enter into Current interface. Please set charge Step 5: If you often use the same battery, please touch Save icon ( Image 13 ) to enter current by sliding ( Image 12 ). Touch OK to go back to main interface and continue setting. into Save interface. Touch Unused icon ( Image 14 ) to save the data and it will be easy for you to charge next time.
Step 6: You could load your previous data according to X350’s load function. Touch Load Step 7: Touch Start icon ( Image 17 ) to enter into Start interface. The system will check icon ( Image 15 ) to enter into Load interface. Choose the data you want to load ( Image 16 ). battery status automatically. If everything is OK, the charger will begin to charge.
【NOTE】The charger will pop-up window when the battery is fully charged. Touch OK to Example 2: If you want to charge a pack of NiMh battery, please execute the oper- finish charging process ( Image 19 ). ation as follows: Input LiPo Step 1: Touch Type icon ( Image 21 ) to enter into Type interface. Touch NiMh icon to go 90 3720 18 06 12.60V 14.0V Type Warning 15 05 12 04 back to main interface and continue setting ( Image 22 ). 75 3100 0.
Step 2: Touch Mode icon ( Image 23 ) to enter into Mode interface. Touch Charge icon ( Image 24 ) to go back to main interface and continue setting. Step 3: Touch Cells icon ( Image 25 ) to enter into Cells interface. Please set NiMh battery packs by sliding ( Image 26). Touch OK to go back to main interface and continue setting.
Step 4: Touch Current icon ( Image 27 ) to enter into Current interface. Please set charge Step 5: Touch Start icon ( Image 29 ) to enter into Start interface. The charger will check current by sliding ( Image 28 ). Touch OK to go back to main interface and continue setting. battery status automatically. If everything is OK, the charger will begin to charge ( Image 30 ). Present Setting Battery Type: LiPo Mode: Balance Cells: 3Cells 11.1V Current: C 4.
【NOTE】The charger will pop-up window when the battery is fully charged. Touch OK to Example 3: If you want to charge a pack of Pb battery, please execute the opera- finish charging process ( Image 30 ). tion as follows, Step 1: Touch Type icon ( Image 32 ) to enter into Type interface. Touch Pb icon ( Image 33) to go back to main interface and continue setting. Image 30 【NOTE】The charger will send out an alert and pop-up window if the setting of the battery packs is incorrect.
Step 2: Touch Mode icon ( Image 34 ) to enter into Mode interface. Touch Charge icon ( Image Step 3: Touch Cells icon ( Image 36 ) to enter into Cells interface. Please set Pb battery 35 ) to go back to main interface and continue setting. packs by sliding ( Image 37 ). Touch OK to go back to main interface and continue setting. Image 34 Image 36 Image 35 Image 37 【NOTE】 There are some options in Mode interface ( Image 35 ). Please set according to your requirement.
Step 4: Touch Current icon ( Image 38 ) to enter into Current interface. Please set charge Step 5:Touch Start icon ( Image 40 ) to enter into Start interface. The charger will check current by sliding ( Image 39 ). Touch OK to go back to main interface and continue setting. battery status automatically. If everything is OK, the charger will begin to charge. ( Image 41 ) Present Setting Battery Type: LiPo Mode: Balance Cells: 3Cells 11.1V Current: C 4.
2 【NOTE】The charger will pop-up window when the battery is fully charged. Touch OK to finish charging process ( Image 42 ). Image 42 X350 Experiments 【NOTE】The charger will send out an alert and pop-up window if the setting of the battery packs is incorrect. ( Image 43 ) All Lipo battery packs setting are the same operation. Image 43 www.imaxrc.com/x350.
iM·OS SYSTEM ADVANCED APPLICATION Touch “Cut off Low Input”( Image 46 ), the information bar on left will skip into setting iM·OS SYSTEM is brand-new software of charger which was Independently research and menu( Image 47 ), touch “OK” after setting done, it will turn back to interface , then you develop by iMaxRC. It is the first operation system in the world especially to support touch can go on with setting of other features.
Cut off Low Input Cut off Low Input Cycle Times Rang of setting:10-11V. Lowest cut off input voltage, charger will stop charging/ discharging when input voltage is lower than setting value. Cut off temperaturey Cut off Temperature Backlight Level Rang of setting: 40-80°C. Cut off Temperature, charger will stop charging/ discharging when the temperature of batteries is lower than setting value. Buzzer Cycle Time Rang of setting: 1-6 times. Backlight Level Rang of setting: 1-10, Brightness level.
3 IMPORTANT REMIND www.imaxrc.com/x350.
Please follow the instruction to operate your X350 charger, to insure safety of you and NEVER use X350 charger under following operating environment: the environment full of charger, and use it easily. Please keep manual within easy reach, to be easy reference for floating dust, smoke from burning or cooking in air. the place have ultrasonic humidifier (for you and other users. unfiltered tap water) working on. In rare cases, these smoke or particles in air may float into X350 charger from air-vent.
All specifications and figures are subject to change without notice.