IE-MiniMc Operation Manual
FCC Radio Frequency Interference Statement Class A (using DC terminal power or Power Over Ethernet (POE)) This equipment has been tested and found to comply with the limits for a Class A computing device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Warranty IMC Networks warrants to the original end-user purchaser that this product, EXCLUSIVE OF SOFTWARE, shall be free from defects in materials and workmanship under normal and proper use in accordance with IMC Networks' instructions and directions for a period of six (6) years after the original date of purchase. This warranty is subject to the limitations set forth below.
Table of Contents FCC Radio Frequency Interference Statement .....................................................i Warranty............................................................................................................ii About the IE-MiniMc..........................................................................................1 Installing the IE-MiniMc......................................................................................1 DIN Rail Mounting.....................................
About the IE-MiniMc The IE-MiniMc Industrial Ethernet miniature media converter features 10/100 switching copper-to-fiber conversion, miniature size, plug-and-play operation, and as a PD device, is compliant to the IEEE 802.3af Power Over Ethernet (PoE) standard. The IE-MiniMc supports an extended voltage range as well as extended operating temperature. Installing the IE-MiniMc The IE-MiniMc installs virtually anywhere: as a standalone, table-top device or on a DIN rail.
Powering the IE-MiniMc The IE-MiniMc includes multiple powering options: • • • • A country-specific, high-reliability AC power adapter (included) The IEEE 802.3af Power over Ethernet standard; draws power from power sourcing equipment The 4-terminal DC power block IE-PowerTray/18 for Rack Mounting About Power Over Ethernet (PoE) and IE-MiniMc Power Over Ethernet technology allows the IE-MiniMc to be a Powered Device (PD) and draw power when connected to Power Sourcing Equipment (PSE).
DC Terminal Block Wiring Instructions The IE-MiniMc can also be powered with the DC terminal block. From a power source, connect to any one positive and any one negative terminal on the IE-MiniMc. +5 VDC NOTE When using stranded wire, the leads must be tinned. The DC terminal block is protected against mis-wiring; if mis-wired, the chassis will not function. The chassis is internally connected to the negative power terminal.
IMC Networks Technical Support Tel: (949) 465-3000 or (800) 624-1070 (in the U.S. and Canada); +32-16-550880 (Europe) Fax: (949) 465-3020 E-Mail: techsupport@imcnetworks.com Web: www.imcnetworks.com Specifications Ethernet Connections 10/100 BaseT, Auto Negotiation, Auto-Cross, Flow Control, 1916 MTU, Broadcast Storm Protection, Full Line-Rate Forwarding. Input Specifications DC terminal DC jack PoE 7 to 50 VDC, 1 to 0.
Fiber Optic Cleaning Guidelines Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, which can obstruct the optic path and cause performance degradation. Good system performance requires clean optics and connector ferrules. 1. Use fiber patch cords (or connectors, if you terminate your own fiber) only from a reputable supplier; low-quality components can cause many hard-to-diagnose problems in an installation. 2.
Electrostatic Discharge Precautions Electrostatic discharge (ESD) can cause damage to any product, add-in modules or stand alone units, containing electronic components. Always observe the following precautions when installing or handling these kinds of products 1. Do not remove unit from its protective packaging until ready to install. 2. Wear an ESD wrist grounding strap before handling any module or component.
Safety Certifications UL/CUL: Listed to Safety of Information Technology Equipment, including Electrical Business Equipment. CE: The products described herein comply with the Council Directive on Electromagnetic Compatibility (2004/108/EC) and the Council Directive on Electrical Equipment Designed for use within Certain Voltage Limits (2006/95/EC). Certified to Safety of Information Technology Equipment, Including Electrical Business Equipment. For further details, contact IMC Networks.
19772 Pauling • Foothill Ranch, CA 92610-2611 USA TEL: (949) 465-3000 • FAX: (949) 465-3020 www.imcnetworks.com © 2011 IMC Networks. All rights reserved. The information in this document is subject to change without notice. IMC Networks assumes no responsibility for any errors that may appear in this document. IE-MiniMc is a trademark of IMC Networks. Other brands or product names may be trademarks and are the property of their respective companies.
