NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction IRON GRIP STRENGTH WEIGHT BENCH IGS-705 Parts List Warranty Ordering Parts Model IGS-705 Retain This Manual for Reference 07-30-08 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICE....................................................................... HARDWARE PACK ……….....…....................................................................... ASSEMBLY INSTRUCTIONS........................................................................... EXPLODED DIAGRAM.........................................................................……….
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WRANING LABEL REPLACEMENT The warning label shown here have been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the label in the location shown.
Hardware Pack NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Upright Beams (#1) by a Cross Brace (#2) in the mid-span. B.) Secure each end of Cross Brace to each Upright Beam with two M10 x 3 1/8” Carriage Bolts (#26), one Weight Post (#10), two Ø ¾” Washers (#35), and two M10 Aircraft Nuts (#33).
STEP 2 (See Diagram 2) A.) Do not tighten the Nuts and Bolts until instructed to do so. B.) Attach the Main Seat Support (#1) to Cross Brace (#2). Secure it with two M10 x 3 1/8” Carriage Bolt (#26), one Bracket (#14), two Ø ¾” Washer (#35), and two M10 Aircraft Nut (#33). C.) Attach the Leg Developer Holder (#4) to the Main Seat Support. Secure it with three M10 x 5/8” Allen Bolts (#27) and three Ø ¾” Washers (#35). D.) Attach the Diagonal Support (#11) to the Main Seat Support and Leg Developer Holder.
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#5) to the Leg Developer Holder (#4). Secure it with one M8 x 2 ¾” Allen Bolt (#29), two Ø 5/8” Washers (#36), and one M8 Aircraft Nut (#34). Do not over tighten the Nut and Bolt. Make sure the Leg Developer is able to swivel. B.) Insert two Foam Tubes (#12) halfway through the holes on Leg Developer. Push four Foam Rolls (#13) onto the Tubes from each end.
STEP 4 (See Diagram 4) A.) Attach the Sliding Block (#7) to the Main Seat Support (#3). Secure it with one M10 x 4” Hex Bolt (#30), one Ø ¾” Washer (#35), and one M10 Aircraft Nut (#33). B.) Attach the pivot on the Backrest Support (#9) to the bracket on Main Seat Support. Secure it with one M10 x 3” Hex Bolt (#31), one Ø ¾” Washer (#35), and one M10 Aircraft Nut (#33). C.) Insert the Incline Adjustment Frame through the Sliding Block.
Step-5 (See Diagram 5) A.) Attach the Backrest Board (#18) to Backrest Support (#9). Secure it with four M6 x ¾” Hex Bolts (#38) and four Ø ½” Washers (#37). B.) Attach the Seat Pad (#39) onto the Main Seat Support (#3). Secure it with four M6 x 1 ¼” Hex Bolts (#32) and four Ø ½” Washers (#37). C.) Attach the two Bar Catches (#6) to the two Upright Beams (#1).
10
PARTS LIST KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.