NOTE: Please read all instructions carefully before using this product Safety Notice Dumbbell Rack Hardware Identifier IVK-402 Assembly Instruction Parts List Warranty Ordering Parts Model IVK-402 Retain This Manual for Reference 09-20-05 OWNER'S MANUAL IMPEX INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICES..................................................................... HARDWARE PACK ……………….................................................................... ASSEMBLY INSTRUCTIONS........................................................................... EXPLODED DIAGRAM.........................................................................………. PARTS LIST.......
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise equipment is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your equipment. In particular, note the following safety precautions: 1. Keep children and pets away from the equipment at all times. DO NOT leave children unattended in the same room with the equipment. 2.
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
HARDWARE PACK 4
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Adjustable Wrench and Allen Wrench NOTE: It is strongly recommended two or more people assembling this equipment to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Cross Brace (#1) in between the Left & Right Upright Beams (#2 & #3). B.) Secure each end with three M10 x 3” Allen Bolts (#15), two Brackets (#5), six Ø ¾” Washers (#14), and three M10 Aircraft Nuts (#13). Do not tighten the Nuts and Bolts yet.
STEP 2 (See Diagram 2) A.) Attach one Floor Stabilizer (#4) in between the two Brackets (#5) to the Right Upright Beam (#3). B.) Secure it with one M10 x 3” Allen Bolt (#15), two Ø ¾” Washers (#14), and one M10 Aircraft Nut (#13). Repeat the same procedure to install the other side. C.) Place the Upper Dumbbell Rack (#7) onto the top dumbbell support on the Left & Right Upright Beams. Secure each end with two M10 x 3” Allen Bolts (#15), four Ø ¾” Washers (#14), and two M10 Aircraft Nuts (#13).
STEP 3 (See Diagram 3) A.) Place the Lower Dumbbell Rack (#6) onto the second level of dumbbell support on the Right and Left Upright Beams. B.) Secure each end with two M10 x 3” Allen Bolts (#15), four Ø ¾” Washers (#14), and two M10 Aircraft Nuts (#13). Repeat the same procedure to install the other Lower Dumbbell Rack. C.) Cover all ends of Upper and Lower Dumbbell Racks with six Dumbbell Rack End Caps (#12). Secure each End Cap with two ½” Philips Screws (#16).
STEP 4 (See Diagram 4) A.) Plug four Base End Caps (#10) onto the base of Upright Beams (#2 & #3) and Floor Stabilizers (#4). B.) Slide the Training Book (#9) onto the Book Rack (#8). Attach the Rack to the back of the Upright Beams. C.) Securely tighten all Nuts and Bolts previously installed.
EXPLODED DIAGRAM 9
Parts list KEY NO.
IVANKO By IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of 2 YEARS from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.