NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction MARCY MAGNUM V HOME GYM Parts List Resistance Chart Warranty Ordering Parts Model MACH V Retain This Manual for Reference 08-26-03 OWNER'S MANUAL IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICE...................................................................... HARDWARE PACK…….......…....................................................................... ASSEMBLY INSTRUCTIONS........................................................................... PARTS LIST...............................................................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
HARDWARE PACK 3
HARDWARE PACK 4
HARDWARE PACK 5
HARDWARE PACK 6
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach two Ø 2 ½” Rubber Bumpers (#88) to the holes on the Main Base Frame (#1). B.) Align the holes and insert two Guide Rods (#10) into the holes. Secure the Guide Rods from the Bottom of Main Base Frame with two M10 x ¾” Allen Bolts (#120) and Ø ¾” Washers (#124).
STEP 2 (See Diagram 2) A.) Connect the Main Base Frame (#1) to both the Front & Rear Stabilizers (#5 & 4). Secure each end with two M10 x 2 ¾” Carriage Bolts (#109), one 4 ¾” x 2” Bracket (#44), two ∅ ¾” Washers (#124), and two M10 Aircraft Nuts (#128). DO NOT tighten all the nuts and bolts yet. B.) Attach the Rear & Front Vertical Beams (#6 & 7) to the Main Base Frame (#1). Secure each Beam with two M10 x 2 ¾” Carriage Bolts (#109), ∅¾” Washers (#124), and M10 Aircraft Nuts (#128). C.
STEP 3 (See Diagram 3) A.) Place the Swivel Frame (#11) onto the axle on the Main Base Frame (#1). Secure it with one M10 x ¾” Allen Bolt (#120) and Ø ¾” Washer (#124). B.) Attach the Foot Support (#12) to the Main Base Frame. Attach the 4” x 2” Bracket (#42) to the opposite side on the Main Base Frame. Secure them with one M10 x 2 ¾” Carriage Bolt (#109), Ø ¾” Washer (#124), and M10 Aircraft Nut (#128) to the hole near the Rear Stabilizer.
STEP 4 (See Diagram 4) A.) Attach the Butterfly Support Frame (#15) to the front of the Front Vertical Beam (#7). Attach the Butterfly Pulley Support (#16) to the back of the Front Vertical Beam (#7). Align the holes and secure them with two M10 x 3 ¾” Carriage Bolts (#107), ∅ ¾” Washers (#124), and M10 Aircraft Nuts (#128). B.) Attach a Pull Pin (#74) to the Left Butterfly Arm (#29). Repeat for the Right Butterfly Arm (#30). C.
STEP 5 (See Diagram 5) A.) Install 19 Weight Plates (#58). To install the plates, hold the plate at an angle and place between the two Guide Rods (#10) then drop it down. Make sure the grooves on the plastic covers all face up. The plates should all interlock with each other. It is strongly recommended to spray lubricant such as WD-40 on the Guide Rods to minimize friction. B.) Insert the Selector Rod (#62) into the center hole on the Weight Plates.
STEP6 (See Diagram 6) A.) Attach the Bench Press Base (#14) to the opening on the Rear Vertical Beam (#6). Carefully place two ∅1 ½” x Ø 1” Washers (#132) in between the Base and the Rear Vertical Beam. Align the holes and insert a 9” Axle (#32). Secure both ends with two ∅1 ½ x ∅ ½”Washers (#133) and M12 Aircraft Nuts (#127). Do not over tighten the Nuts. Make sure the Base is free to swivel on the Axle. Close both ends with two Cone-shaped End Caps (#105). B.
STEP 7 (See Diagram 7) A.) Slide the Sliding Block (#37) onto the Main Seat Support (#2). Thread a Lock Knob (#87) into the hole on the Sliding Block to hold it in position. B.) Attach the rear end of Main Seat Support (#2) to the open bracket on the Front Vertical Beam (#7). Secure it with three M10 x 2 ¾” Carriage Bolts (#109), Ø ¾” Washers (#124), and M10 Aircraft Nuts (#128). C.) Place the Main Seat Support (#2) onto the Front Support Frame (#3).
STEP 8 (See Diagram 8) A.) Attach Backrest Board (#48) to the Front Vertical Beam (#7). Secure it with two M8 x 3 3/8” Allen Bolts (#115) and Ø 5/8” Washers (#125). B.) Attach the Adjustable Backrest Board (#49) to the Backrest Supports (#25). Secure it with four M6 x 1 3/8” Hex Bolts (#112) and Ø ½” Washers (#126). C.) Place the Seat (#50) onto the Seat Bracket (#18). Secure it to the two rear holes on the Seat Bracket with two M8 x ¾” Allen Bolts (#122) and Ø 5/8” Washes (#125).
STEP 9 (See Diagram 9) A.) Attach the two Weight Stack Covers (#39) to the Top Socket Assembly (#9) and Main Base Frame (#1). Secure each Cover with two M10 x ¾” Allen Bolts (#120) and Ø ¾” Washers (#124).
16
STEP 10 (See Cable Loop Diagram & Diagram 10) A.) Attach one end of the 143” Butterfly Cable (#56) to the Clip on the Butterfly Pulley Bracket (#17) on the right side. Draw the Cable to the Butterfly Pulley Support (#16). B.) Attach a Pulley (#66) to the open bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#113), two Ø ¾” Washers (#124), and one M10 Aircraft Nut (#128). C.) Draw the Cable over the Pulley then pull downward.
STEP 11 (See Cable Loop Diagram & Diagram 11) A.) Attach the 118” Upper Cable (#52) to the front opening on the Upper Frame (#8). Attach a Pulley to the opening. Secure the Pulley with one M10 x 2 ½” Allen Bolt (#117), two Ø 7/8” Pulley Bushings (#70), and one M10 Aircraft Nut (#128). Make sure the Ball Stopper of the Cable is underneath the Frame. B.) Draw the Cable over the Pulley and toward the back of the machine. Attach a Pulley to the open bracket on the top of the Upper Frame.
DIAGRAM 11 19
STEP 12 (See Cable Loop Diagram & Diagram 12) A.) Attach the Ball-end of the 163” AB Cable (#55) to the opening on the Front Vertical Beam (#7). Attach a Pulley to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#117), two Ø 7/8” Pulley Bushings (#70), and one M10 Aircraft Nut (#128). Use a C-clip (#136) to connect the AB Strap (#59) to the end of the Cable. B.
DIAGRAM 12 21
STEP 13 (See Cable Loop Diagram & Diagram 13) A.) Attach one end of the 78” Bench Press Cable (#54) to a Single Floating Pulley Bracket (#35). Secure it with one M10 x 1” Allen Bolt (#114), two Ø ¾” Washers (#124), and one M10 Aircraft Nut (#128). Let the Bracket hanging for now. B.) Pull the Cable upward to the opening between the Bench Press Base (#14). Attach a Pulley to the opening. Secure it with one 7” Axle (#130) and two M8 Hex Socket Screws (#82). C.
STEP 14 (See Cable Loop Diagram & Diagram 14) A.) Attach the 163” Lower Cable (#53) to the Swivel Frame (#11). B.) Install a Pulley to the bracket on the Swivel Frame with one M10 x 1 ¾” Allen Bolt (#113), two Ø ¾” Washers (#124), one L-shaped Bracket (#46) and one M10 Aircraft Nut (#128). C.) Draw the Cable around the Pulley then pull upward to the Double Floating Pulley Bracket (#36) previously installed in Step12-E. Install another Pulley. D.
24
PARTS LIST KEY NO.
110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 M10 x 7 ¼” Hex Bolt M6 x 1 5/8” Hex Bolt M6 x 1 3/8” Hex Bolt M10 x 1 ¾” Allen Bolt M10 x 1” Allen Bolt M8 x 3 3/8” Allen Bolt M10 x 3” Allen Bolt M10 x 2 ½” Allen Bolt Ø ¾” Bushing M10 x 1 ¾” Allen Bolt (Full Thread) M10 x ¾” Allen Bolt M8 x 5/8” Allen Bolt M8 x ¾” Allen Bolt M6 x 5/8” Allen Bolt Ø ¾” Washer Ø 5/8” Washer Ø ½” Washer M12 Aircraft Nut 1 2 4 17 4 2 1 5 2 1 13 2 4 3 84 8 4 4 128 129 130 131 132 133 134 135 136 137 138
MACH IV WEIGHT RESISTANCE CHART Plate 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Arm Curl 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 Low Pulley 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 High Pulley 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 Butterfly * Numbers are approximate. Actual weights may vary. * Values for Butterfly are for each arm.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.
