NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction MARCY HOME GYM MWM-8150 Parts List Resistance Chart Warranty Ordering Parts Model MWM-8150 Retain This Manual for Reference 08-04-08 OWNER'S MANUAL IMPEX® INC. 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICE...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 8 PARTS LIST………………………………………………………………………………….. 21 RESISTANCE CHART…………....................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Base and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches, two Allen Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Insert the two Guide Rods (#7) into the holes on the Rear Base Frame (#2). Secure it with two M10 x 1” Allen Bolts (#71) and Ø ¾” Washers (#80) from the bottom.
DIAGRAM 1 9
STEP 2 (See Diagram 2) A.) Slide 14 Weight Plates (#33) onto the Guide Rods. Make sure the deep groove on the Weight Plates all facing the front of the machine and downward. Insert the Selector Rod (#28) through the center hole on the Weight Plates. Slide the Selector Stem (#32) onto the Guide Rods. Use the L-shaped Pin (#39) to select total weights to exercise. Please refer to the Weight Resistance Chart in page 22. B.) Place the Upper Frame (#5) onto the Vertical Frame (#4).
DIAGRAM 2 11
STEP 3 (See Diagram 3) A.) Attach the Seat Support (#8) to the Vertical Frame (#4). Secure it with two M10 x 2 ½” Carriage Bolts (#65), one 4 ¾” x 2” Bracket (#23), two Ø ¾” Washers (#80), and two M10 Aircraft Nuts (#82). Do not tighten the Nuts and Bolts yet. B.) Attach the two Seat Support Frames (#10) to the Seat Support and the Main Base frame (#1) from each side.
STEP 4 (See Diagram 4) A.) Attach two Ø 1” Bushings (#44) to the holes on the Upper Frame (#5). Attach the Front Press Base (#11) to the two Bushings. Secure it with one M12 x 4 1/8” Allen Bolt (#68), two Ø 1” Washers (#81), and one M12 Aircraft Nuts (#63). Do not over tighten the Nut and Bolt. Make sure the Front Press Base is able to move smoothly. B.) Attach the Right Butterfly (#13) to the Front Press Base.
CABLE LOOP DIAGRAM 14
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 153” Upper Cable (#34) to the opening at the front of the Upper Frame (#5). Note: The Ball Stopper on the cable should be underneath the Frame. B.) Attach a Pulley (#47) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#74), two Ø 7/8” x 5/8” Pulley Bushings (#43), and one M10 Aircraft Nut (#82). C.) Draw the Cable towards the back of the machine to the opening on the Upper Frame. Attach a Pulley to the opening.
DIAGRAM 5 16
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 125” Butterfly Cable (#35) to the hook on the Right Butterfly (#13). B.) Draw the Cable to the right Swivel Pulley Bracket (#16). C.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#72), two Ø ¾” Washers (#80), and one M10 Aircraft Nut (#82). D.) Draw the Cable around the Pulley then downward. Attach the Cable to a Crossed Double Floating Pulley Bracket (#17). Install another Pulley.
DIAGRAM 6 18
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 131” Lower Cable (#36) to the opening on the bottom of the Leg Developer (#9). B.) Attach a Pulley to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#74), two Ø 7/8” x 5/8” Pulley Bushings (#43), and one M10 Aircraft Nut (#82). C.) Draw the Cable underneath the Pulley to the opening in between the two Seat Support Frames (#10). D.) Attach a Pulley to the opening.
DIAGRAM 7 20
PARTS LIST KEY NO.
22
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.