NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice MARCY DIAMOND ELITE OLYMPIC BENCH Hardware Pack Assembly Instruction MD-739 Parts List Warranty Ordering Parts Model MD-739 Retain This Manual for Reference 110816 OWNER'S MANUAL IMPEX® INC. 2801 S. Towne Ave., Pomona, CA 91766 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 6 EXPLODED DIAGRAM…………………………………………………………………….. 10 PARTS LIST………….…………...................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
HARDWARE PACK 5
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten all nuts and bolts until instructed to do so. B.) Attach the Left Diagonal Support (#3) to the Left Upright Beam (#1) from rear. Attach the Cross Brace (#5) to the Left Upright Beam from the other side.
STEP 2 (See Diagram 2) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Front Post (#6) to the Main Seat Support (#7). Secure it with one M10 x 4” Carriage Bolt (#32), one Ø ¾” Washer (#40), and one M10 Aircraft Nut (#43) from side. Secure it with two M10 x 2 1/8” Carriage Bolts (#34), two Ø ¾” Washers (#40), and two M10 Aircraft Nuts (#43) from top. C.) Attach the Main Seat Support to the Cross Brace (#5).
STEP 3 (See Diagram 3) A.) Attach the Seat Bracket (#10) to the pivot on Main Seat Support (#7). Attach the two Backrest Supports (#9) to the Seat Bracket from each side. Secure them together with One M12 x 7 1/8” Hex Bolt (#31), two Ø 1” Washers (#39), and one M12 aircraft Nut (#42). B.) Attach the Backrest Board (#17) to the Backrest Supports. Secure it with four M8 x 1 5/8” Allen Bolts (#37) and four Ø 5/8” Washers (#41). C.) Attach the Seat Pad (#16) to Seat Bracket.
8 STEP 4 (See Diagram 4) A.) Attach two Ø ¾” x Ø 3/8” Bushings (#29) to the Leg Developer (#12). Attach the Leg Developer to the open bracket on Front Post (#6). Secure it with one M10 x 3 1/8” Allen Bolt (#35), two ¾” Washers (#40), and one M10 Aircraft Nut (#43). B.) Insert one Long Foam Tube (#13) and two Foam Tubes (#14) halfway through the holes on the Front Post and Leg Developer. Push six Foam Rolls (#19) onto the Tubes from both ends. Plug six Foam Roll End Caps (#26) into the ends. C.
10
PARTS LIST KEY NO.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.