NOTE: Please read all instructions carefully before using this product Table of Contents WEIGHT BENCH MSS-7500 Safety Notice Hardware Pack Assembly Instruction Exploded Diagram Parts List Warranty Ordering Parts Model MSS-7500 Retain This Manual for Reference 06/11/09 IMPEX® INC. OWNER'S MANUAL 14777 Don Julian Rd., City of Industry, CA 91746 Tel: (800) 999-8899 Fax (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICE....................................................................... HARDWARE PACK………............................................................................... ASSEMBLY INSTRUCTIONS........................................................................... EXPLODED DIAGRAM....................................................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL PLACEMENT The Warning Labels shown here have been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
ASSEMBLY INSTRUCTION Tools Required For Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended for two or more people to assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten the Nuts and Bolts until instructed to do so. B.) Connect the two Upright Beams (#1) by a Cross Brace (#2) in the mid-span.
STEP 2 (See Diagram 2) A.) Attach the Main Seat Support (#3) to the Front Post (#4). Secure it with two M10 x 2 3/8” Carriage Bolts (#32), one 6 ¼” x 3 ¼” Bracket (#14), two Ø ¾” Washers (#36), and two M10 Aircraft Nuts (#38). B.) Attach the Main Seat Support to the Cross Brace (#2). Secure it with two M10 x 2 ½” Carriage Bolts (#31), one 5 ½” x 3” Curved Bracket (#15), two Ø ¾” Washer (#36), and two M10 Aircraft Nut (#38). C.) Securely tighten all Nuts and Bolts in Step-1 and Step-2.
STEP 3 (See Diagram 3) A.) Attach the Seat Bracket (#5) to the pivot on the Main Seat Support (#3). Attach the holes on the end of the two Backrest Supports (#6) to the Seat Bracket. Align the holes. Secure the two Backrest Supports, Seat Bracket together to the pivot with one M12 x 7” Hex Bolt (#26), two Ø 1” Washers (#37), and one M12 Aircraft Nut (#39). Do not over tighten the Nuts and Bolts. Make sure the Backrest Supports are able to swivel. B.
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#9) to the open bracket on Main Seat Support (#3). Secure it with one Leg Developer Axle (#21), two M10 x ¾” Allen Bolt (#33), and two Ø ¾” Washers (#36). Do not over tighten the Bolts. Make sure the Leg Developer is able to swivel. B.) Insert two Foam Tubes (#10) halfway through the holes on the Leg Developer. Push four Foam Rolls (#19) onto the Tubes from both ends. Plug four Foam Roll End Caps (#26) into the ends. C.
10
PARTS LIST KEY NO.
IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.