NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice MARCY SMITH BENCH Hardware Pack Assembly Instruction SM-600 Parts List Warranty Ordering Parts Model SM 600 Retain This Manual for Reference 08-18-03 OWNER'S MANUAL IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICE....................................................................... HARDWARE PACK…….......…....................................................................... ASSEMBLY INSTRUCTIONS........................................................................... EXPLODED DIAGRAM.........................................................................……….
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
HARDWARE PACK 3
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Stabilizers (#1) by a Cross Brace (#4) in the mid-span. Align the holes and secure each end with one 6 ½” x 2” Bracket (#12), two M10 x 2 ¾” Carriage Bolts (#23), two ∅ ¾” Washers (#25), and two M10 Aircraft Nuts (#24). B.
STEP 2 (See Diagram 2) A.) Slide both a Rubber Bumper (20) and Safety Stop (#6) onto a Guide Rod (#8). B.) Slide a Sliding Bar Catch (#5) onto the Guide Rod from the top. C.) Insert the bottom of Guide Rod into the ring cap on the left Stabilizer. Insert the top of Guide Rod into the ring cap on top of the left Upright Beam. Use the two M8 x ½” Allen Screws (#14) on the caps to secure the Guide Rod. D.) Attach a Safety Hook (#7) to the bracket on the Safety Stop (#6).
STEP 3 (See Diagram 3) A.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting Sleeve (#9) in between the two Sliding Bar Catches (#5). Align the holes. Insert the Weight Bar (#10) into the Bar Catch from one end and through the Lifting Sleeve to the other Bar Catch on the opposite end. Center the Weight Bar and secure it to each Bar Catch with one M10 x 5/8” Allen Bolt (#43). B.
STEP 4 (See Diagram 4) A.) Attach the rear of the Bench Main Base Frame (#27) to the Bench Rear Stabilizer (#28). Secure it with one 4 ¾” x 2” Bracket (#13), two M10 x 2 ¾” Carriage Bolts (#23), two Ø ¾” Washers (#25), and two M10 Aircraft Nuts (#24). B.) Attach the front of the Bench Main Base Frame (#27) to the Bench Front Stabilizer (#45). Secure it with one 4 ¾” x 2” Bracket (#13), two M10 x 2 ¾” Carriage Bolts (#23), two Ø ¾” Washers (#25), and two M10 Aircraft Nuts (#24). C.
STEP 5 (See Diagram 5) A.) Attach two Ø ½” Bushings (#35) to both ends of the pivot on the Backrest Incline Support (#30). B.) Place the Backrest Incline Support (#30) in between the two Backrest Supports (#29). Align the holes. Insert one M10 x 7 ¼” Allen Bolt (#39) through the holes and secure it with two Ø ¾” Washers (#25), and one M10 Aircraft Nut (#24). Do not tighten the Nut and Bolt yet. C.) Attach two Bushings (#35) to the front hole of each Backrest Support (#29). D.
STEP 6 (See Diagram 6) A.) Place the Backrest Board (#33) onto the Backrest Supports. Secure it with four M6 x 2” Hex Bolts (#41) and Ø ½” Washers (#42). B.) Place the Seat (#34) onto the Seat Supports. Secure it with four M6 x 2” Hex Bolts (#41) and Ø ½” Washers (#42).
10
PARTS LIST KEY NO.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.