NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier COMPETITOR BENCH WM-354 Assembly Instruction Parts List Warranty Ordering Parts Model WM-354 Retain This Manual for Reference 05-27-03 OWNER'S MANUAL IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................…. IMPORTANT SAFETY NOTICES..................................................................…. HARDWARE IDENTIFIER.....…....................................................................…. ASSEMBLY INSTRUCTIONS........................................................................…. EXPLODED DIAGRAM………………………………………………………………. PARTS LIST.......................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
HARDWARE IDENTIFIER 3
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Plug the two Stabilizer End Caps (#24) onto the bottom of the two Rear Upright Beams (#1). B.) Connect the two Rear Upright Beams by a Cross Brace (#2) in the Mid-span.
STEP 2 (See Diagram 2) A.) Plug a Stabilizer End Cap (#24) onto the bottom of Front Leg (#8). Attach the Front Leg to the Main Seat Support (#6). Secure it with three M8 x 5/8” Hex Bolts (#33) and Ø 5/8” Washers (#28). DO NOT tighten the Bolts yet. B.) Attach the Main Seat Support (#6) to the Cross Brace (#2). Secure it with two M10 x 2 3/8” Hex Bolts (#30), four Ø ¾” Washers (#31), one Flat Bracket (#5), and two M10 Aircraft Nuts (#32). C.
STEP 3 (See Diagram 3) A.) Attach one ∅3/4” Washer (#31) onto a M10 x 6” Hex Bolt (#35). Insert the Bolt through the Butterfly (#9). Secure the Bolt with one M10 x 5/8” Regular Nut (#36) B.) Insert the Bolt through the Rear Upright Beam (#1). Secure it with a Ø ¾” Washer (#31) and M10 Aircraft Nut (#32). DO NOT over tighten the Bolt. Make sure the Butterfly is able to swivel on the Upright Beam. C.) Insert a Butterfly Foam Tube (#10) through the hole on the Butterfly. Push a Foam Roll (#20) onto the Tube.
STEP 4 (See Diagram 4) A.) Attach the hole-side of the Backrest Supports (#14) onto both ends of the pivot on the Main Seat Support (#6). Place the other end rest against the Backrest Adjustment Bar (#4). B.) Place the Backrest Board (#15) onto the Backrest Supports. Secure it with four M6 x 1 3/8” Hex Bolts (#37) and Ø ½” Washers (#38). C.) Place the Seat Pad (#16) onto the Main Seat Support. Secure it with four M6 x 1 3/8” Hex Bolts (#37) and Ø ½” Washers (#38).
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#17) to the Arm Curl Stand (#13). Secure it with two M8 x 5/8” Hex Bolts (#33) and Ø 5/8” Washers (#28). B.) Insert the Arm Curl Stand into the top opening on the Front Leg. Secure it with a Lock Knob (#25).
9
PARTS LIST KEY NO.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.