Use and Care Manual
3 - ENG
200-3171
RISK TO BREATHING. Be certain to read all labels when you are spraying paints or toxic materials, and follow the safety
instructions provided on the label or safety sheets for the materials you are spraying. Use a MSHA/
NIOSH approved respirator mask if there is a chance of inhaling anything you are spraying. Read
all instructions and be sure that your respirator mask will protect you. Work in an area with good
cross ventilation.
RISK OF EYE INJURY. Always wear ANSI Z87.1 approved safety goggles when using an air compressor. Never point any
nozzle or sprayer toward a person, animal or any part of the body. Equipment can cause serious
injury if the spray penetrates the skin.
RISK OF BURSTING. •Do not adjust the tank safety valve for any reason. Doing so voids all warranties. The safety valve
has been pre-set at the factory for the maximum pressure of this unit. Personal injury and /or
property damage may result if the relief valve is tampered with.
•Do not use plastic or pvc pipe for compressed air. Use only galvanized steel pipe and fittings for
compressed air distribution lines.
RISK OF FIRE.
Unattended operation of this compressor could result in personal injury or property damage. To
reduce the risk of fire, do not allow the compressor to operate unattended. Always disconnect
electrical power by turning the pressure switch to off and drain the tank daily or after each use.
RISK TO BREATHING.
Air obtained directly from the compressor should never be used to supply air for human
consumption. The air stream may contain carbon monoxide, toxic vapors, or solid particles from
tank. Breathing these contaminant’s can cause serious injury or death. In order to use air produced
by this compressor for breathing, suitable filters and in-line safety equipment must be properly
installed. In-line filters and safety equipment must be properly installed. In-line filters and safety
equipment used in conjunction with the compressor must be capable of treating air to all applicable
local and federal codes prior to human consumption.
RISK OF INJURY.
Always operate the compressor in a stable secure position to prevent accidental movement of the
unit.
RISK TO HEARING.
Always wear hearing protection when using an air compressor. Failure to do so may result in
hearing loss.
NOTE: ELECTRICAL WIRING.
Refer to the air compressor’s serial label for the unit’s voltage and amperage requirements. Ensure
that all wiring is done by a licensed electrician, in accordance with the National Electrical code.
WARNING: CONTAINS LEAD. May be harmful if eaten or chewed. May generate dust containing
lead. Wash hands after use. Keep out of reach of children.
WARNING: This product can expose you to chemicals including Lead, which is known to the State
of California to cause cancer and birth defects or other reproductive harm. For more information go
to www.P65Warnings.ca.gov.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
Drain the moisture from the tank on a daily basis. A clean, dry tank will help prevent corrosion.
Pull the tank safety valve ring daily to ensure that the valve is functioning properly, and to clear the valve of any possible obstructions.
To provide proper ventilation for cooling, the compressor must be kept a minimum of 12 inches (31 cm) from the nearest wall, in a
well–ventilated area. Restricting any of the compressor ventilation openings will cause overheating and could cause fire, never place
objects against or on top of compressor.
Fasten the compressor down securely if transporting is necessary. Pressure must be released from the tank before transporting.
Protect the air hose and interconnect cord from damage and puncture. Inspect them weekly for weak or worn spots, and replace if
necessary.
Risk of electric shock or injury - Use indoors only.
On oil-lubed compressors, oil can leak or spill and could result in fire or breathing hazard. Oil leaks will damage paint, carpet or other
surfaces in vehicles or trailers. Always place the compressor on a protective mat when transporting to protect against damage to
vehicle from leaks. Remove compressor from vehicle immediately upon arrival at your destination.
To prevent damage to tank and compressor on stationary models, the tank must be shimmed so the pump base is level within 1/8” to
distribute oil properly. All feet must be supported, shimming where necessary, prior to attaching to the floor. Fasten all feet to floor. We
also recommend the use of vibration pads (094-0137) under tank feet.