Installation Manual

Rev 2.0 April 2020Rev 2.0 April 2020
Installation Manual
The SIFER Reader Add-on kit provides an EliteX or PrismaX Terminal with a built-in Multi-
format SIFER Reader allowing user operations that require a SIFER credential.
Refer to the appropriate system manual/s for EliteX, PrismaX and SIFER Reader
programming and commissioning information.
Controller Firmware Compatibility
Integriti/Infiniti Controller: V17.0.1 (EliteX) or V18.1 (PrismaX) or later.
Inception Controller: V1.3.5 or later. (EliteX only. PrismaX not supported)
* North American Installations
In North America, this kit must only be installed in an EliteX Terminal (P/N: 995400)
For EliteX Terminal installations refer to the FCC/ISED notices on page 4.
Installing this device in a PrismaX Terminal, P/N: 996400, is not permitted within North
America. Any operation of this device when installed into a PrismaX terminal host module
may cause interference.
EliteX/PrismaX Terminal Installation & User notes.
When this SIFER Reader kit is fitted to an EliteX or PrismaX Terminal:
1. Mounting Surface. SIFER Readers are optimized for mounting on a non-metallic
surface. Mounting the EliteX/PrismaX Terminal on a metallic surface will decrease
the read range. To improve read range on a metallic surface, a non-metallic spacer
or mounting block that provides 8mm or more of separation is recommended.
2. In/Out Readers. If two SIFER products are installed back to back on either side of
a Door, mount the Readers/Terminals at different heights to minimize interference.
3. Reader Zone. The optimum zone for presenting a credential to the Terminal’s
SIFER Reader is in the middle of the blue & grey function & digit key section of the
keypad. i.e. Over the ‘4’, ‘5’, ‘7’ & ‘8’ keys.
Inner Range
SIFER Reader Add-on kit
For EliteX and PrismaX* Terminals
Part Number: 994721PCB&K
Disclaimer
The manufacturer &/or its agents take no responsibility for any damage, financial loss or injury caused to any
equipment, property or persons resulting from the correct or incorrect use of the system or its peripherals. The
purchaser assumes all responsibility in the use of the system and its peripherals.
© 2018 - 2020. Inner Range Pty. Ltd. Knoxfield. Australia. Document Part No: 634721
Email: [e-mail] Web: www.innerrange.com
UL Requirements (North America)
Refer to the Inner Range host LAN Module Installation manual for details of UL regulatory
requirements.
FCC (North America)
This device complies with Part 15 of the FCC Rules and Innovation, Science and Economic
Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
Class B product:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off & on,
the user is encourage to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help
Warning: Any changes or modifications not expressively approved by Inner Range Pty Ltd could void
the user's authority to operate this equipment
ISED (Canada)
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
CAN ICES-3 (B)/NMB-3(B)
14