USER GUIDE Single- and Dual-Tap Kegerator/Beverage Cooler NS-BK1TSS6/NS-BK2TSS6 Before using your new product, please read these instructions to prevent any damage.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Grounding requirement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Introduction Congratulations on your purchase of a high-quality Insignia product. Your NS-BK1TSS6 or NS-BK2TSS6 represents the state of the art in kegerator/beverage cooler design and is designed for reliable and trouble-free performance. Important Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol indicates that dangerous voltage constituting a risk of electric shock is present within your kegerator/beverage cooler.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the appliance. 11 Do not attempt to modify or extend the power cord of this appliance. 12 Unplug this appliance during lightning storms or when it will not be used for long periods of time. 13 Make sure that the available AC power matches the voltage requirements of this appliance.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 2) Leave the shelves in place so that children may not easily climb inside 5 Unplug the kegerator/beverage cooler before performing user maintenance on it.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Features • • • • • • • • 5.6 cu. ft.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Keg parts Single draft arm assembly (single-tap model only) Beer tap handle (one for single-tap, two for dual tap.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Single-tap model Draft arm assembly Guardrail Thermostat (on the back of the unit) Drip tray Worktop CO2 tank CO2 tank regulator Keg coupler CO2 tank retainer Locking casters Beer keg 8 www.insigniaproducts.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Dual-tap model Draft arm assembly Guardrail Thermostat (on the back of the unit) Drip tray Worktop Keg couplers CO2 tank regulator CO2 tank CO2 tank retainer Locking casters Beer keg Locating your kegerator/beverage cooler Before using your kegerator/beverage cooler • • • Let the kegerator/beverage cooler stand upright for approximately eight hours before connecting it to power.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Finding a suitable location • • • • • This kegerator/beverage cooler is designed to be free standing only, and should not be recessed or built-in. Place your kegerator/beverage cooler on a floor that is strong enough to support the kegerator/beverage cooler when it is fully loaded. Allow three inches of space between the back and sides of the kegerator/beverage cooler and any surrounding walls. This allows for proper air ventilation.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Notes • The kegerator/beverage cooler should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate. • We strongly recommend that you do not use an extension cord.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 6 Step on the front of the locking casters to lock the kegerator/beverage cooler into place or step on the back to unlock the kegerator/beverage cooler. Attaching the guard rail • Insert the guard rail into the holes on the top of the kegerator/beverage cooler. Installing the draft arm assembly 1 Remove the round cabinet plug from the top of the kegerator/beverage cooler. You may need to push the cabinet plug up from the inside.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler d Attach the draft arm to the worktop with the four screws provided. Beer tap handle Silver snug ring Draft arm assembly Beer tube Wing nut 2 Attach the black plastic beer tap handle to the top of the faucet, tightening it by hand until it's tight. Hold the silver snug ring so it does not move. Note If there is a small drip after you pour a beverage, you may have tightened the beer tap handle too much.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 5. NEVER drop or throw a CO2 tank. 6. ALWAYS keep a CO2 tank away from heat. Store extra tanks in a cool place (preferably 70°F). Securely fasten with a chain in an upright position when storing. 7. ALWAYS ventilate and leave the area immediately if CO2 leakage has occurred. 8. ALWAYS check the D.O.T. test date on the tank neck before installation. If the tank if over five (5) years old, do not use it. Return the tank to the gas supplier. 9.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Tank valve Dual-tap model CO2 gauge CO2 regulator Gas line connector Regulator nut Hose clamp CO2 tank CO2 gas lines T-connector Hose clamp CO2 gas line Hose clamp Hose clamp Single-tap model: 1 Feed a hose clamp over the end of the CO2 gas line. 2 Attach that end to the gas line connector on the CO2 regulator. 3 Tighten the clamp to prevent leaks. Leave about ½ inch between the top of the clamp and the end of the hose.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 6 Feed a hose clamp over the non-threaded ends of the other two CO2 gas lines. 7 Connect the gas lines to the ends of the T-connector, then tighten the hose clamps. Leave about ½ inch between the top of the clamp and the end of the hose. 8 Attach the CO2 regulator to the CO2 tank by screwing the regulator nut onto the CO2 tank valve and tightening with an adjustable wrench.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Installing and setting up a beer keg This kegerator/beverage cooler accepts almost all brand name kegs, except for Coors kegs. Keg sizes that can be used in your kegerator/beverage cooler: Barrel Liters Gallons Ounces 12 oz. Glasses 1/2 59 15.5 1984 164 1/4 30 7.8 992 82 1/6 20 5.2 661 55 1/8 15 4.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 4 Repeat steps 1-3 if you have a second keg. 5 Pull the black handle on the keg coupler and press it downward until it locks into position. The keg is now tapped. Note If beer comes up through the top of the wing nut, remove the wing nut, reposition the washer, then reattach the wingnut.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Using your kegerator/beverage cooler Setting the temperature The temperature range of the thermostat goes from 32° F to 45° F (0° C to 7° C). The optimum temperature for serving draught beer is between 34° F - 38° F (1.1° C - 3.3° C). We suggest that you keep an accurate thermometer handy to help you to adjust the temperature setting to your needs.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 4 Open faucet handle quickly and completely and fill the glass to 2/3 full. 5 Level the glass and finish topping it off by pouring into the center of the glass. 6 Fully close the tap when the draw is complete. Automatic defrosting There is no need to defrost your kegerator/beverage cooler. The defrost water collects at the back of your cooler and passes through a drain outlet into a tray located above the compressor where it evaporates.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Cleaning the beer components To prevent a build-up of yeast and mold in the beer lines, and to prevent a bad taste, clean your beer components when you replace a keg. 1 Remove the keg coupler and thoroughly rinse it in warm water. 2 Use the included wrench to remove the faucet(s) on the draft arm assembly. Insert the tip of the wrench into one of the holes on the faucet, rotate it, then thoroughly rinse the faucet in warm water.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Storing your kegerator/beverage cooler If you will be away from your kegerator/beverage cooler for more than three weeks. 1 Turn off the kegerator/beverage cooler and unplug it from the wall outlet. 2 Remove all kegs and beverages. 3 Clean and dry the interior of the kegerator/beverage cooler. 4 Leave the door open slightly to avoid possible formation of condensation, mold, or odor. Caution Use extreme caution with children.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Troubleshooting - beer quality Problem Possible cause Excess formation of Recent keg agitation. foam “head.” Beer is all foam, or too much foam and not enough liquid Improper regulator setting. beer. The Internal temperature of the kegerator is too warm. Pressure build up. Possible solution If the keg has recently been moved, let it stand a minimum of two hours before tapping. Verify that the (CO2) pressure is reading between 10 and 12 PSI.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Problem Possible cause Possible solution Abnormal beer taste and/or smell. System requires cleaning. See “Maintaining your kegerator/beverage cooler.” System contamination. Check hoses for possible air leaks. The beer has exceeded its shelf Replace the beer keg with a fresh one. life. Troubleshooting - cooler Caution Do not try to repair your kegerator/beverage cooler yourself. Doing so invalidates the warranty.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Problem Possible cause The cooler turns on and The room temperature is off frequently hotter than normal. Possible solution Make sure that the door was properly installed. The door has been opened too Make sure that the door is closed properly. often or was not closed properly. The door gaskets do not seal properly. Clean the door gaskets. The temperature control is set Set the control to a colder setting. too warm.
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler ONE-YEAR LIMITED WARRANTY - INSIGNIA Definitions: The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler • Commercial purposes/use, including but not limited to use in a place of business or in communal areas of a multiple dwelling condominium or apartment complex, or otherwise used in a place of other than a private home. • Modification of any part of the Product, including the antenna • Display panel damaged by static (non-moving) images applied for lengthy periods (burn-in).
www.insigniaproducts.com 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico) INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC ©2017 Best Buy. All rights reserved. Made in China.
