Specification

Model
F-1000 Replacement Filter
For cleaner, fresher-tasting water
Submittal Sheet
Job Specifications
Instant Hot Water Dispensers
HWD440-13D-45-10 Printed in USA
• Includes 1 replacement filter for use
with InSinkErator water filtration system
• Reduces particulates, chlorine taste and
odor for clean, refreshing taste
• Sanitary, quick-change filter cartridge
makes replacement easy. A simple twist
is all it takes!
• Replace every 6 months at the rated
capacity or if a noticeable reduction
in flow rate occurs
Dimensions
Specifications
Filter Capacity
Temperature
Range
Pressure
Flow Rate
Shipping Weight
500 gallons
30-120 psi
.75 gpm
Approximately 1.0 lbs.
Incoming cold water
supply line can be
from 33˚F to 100˚F
(1˚C to 38˚C).
Connect to cold water
supply line only.
2-1/4 "
11-3/4 "
1-800-558-5700
USA
Canada
www.insinkerator.com
www.insinkerator.ca
The Emerson logo is a trademark
and a service mark of Emerson Electric Co.
InSinkErator may make improvements and/or changes
in the specifications at any time, in its sole discretion,
without notice or obligation and further reserves the
right to change or discontinue models.
©2013 InSinkErator, a business unit of
Emerson Electric Co. All Rights Reserved.
The Next
Necessity
™
F-1000 Cartridge (included with this system) Chemical & Mechanical Reduction Filter Specifications:
This cartridge provides mechanical and chemical reduction of chlorine taste & odor and particulate class III.
Filter Capacity: 500 gallons, depending on local water conditions. Note that while the testing was performed under
standard laboratory conditions, actual performance may vary. Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before or after the system. For cold water use only. Systems must be
installed and operated in accordance with the Manufacturer’s recommended procedures and guidelines. See warranty
card for warranty. For service and parts, contact your local dealer or InSinkErator
®
directly at 1-800-558-5700.
Application guidelines/Water Supply Parameters for NSF Testing: Service flow of .75 gpm, community or
private well water supply, water pressure of 20-120 psi (138-827 kPa), water temperature of 33˚F–100˚
Nominal
Particulate Class III,
≥5 µm to <15 µm
270,000 pts/mL
2.1 mg/L 2.0 mg/L ± 10%
At least 10,000
particles/mL
82 pts/mL 99.9% ≥85%
0.06 mg/L 97.0% ≥ 50% J-00082587
J-00119308
F Except as
noted, all testing performed at pH = 7.5 ± 0.5, Flow: .75 gpm, P ressure: 60 psi, Temp: 20˚±3˚C.
Contact an authorized InSinkErator service agent for repairs or replacement components. Replacement filters
F-1000 and F-2000 can be ordered by calling 800-558-5700, visiting shop.insinkerator.com, or by contacting
an authorized InSinkErator reseller.
Refer to the Performance Data Sheet for InSinkErator Filter System Model F-2000S
Replacement Cartridge: F-2000
Pressure: 30-120 (207-827 kPa) psi
Temperature: 33
º
F - 100
º
F
Flow Rate: .75 gpm
Capacity: 500 gallons
Tested & Certified by NSF International against NSF/ANSI Standard 42 in the following
InSinkErator Systems Only: GN1100, HC1100, GN2200, HC2200, GN2215, HC2215,
H3300 or HC3300 for the reduction of claims specified on the Performance Data Sheet.
For systems using two handle HC model faucets, operate only one handle at a time.