Back

ManualsBrandsIntel ManualsOtherIntel Server System P4308CP4MHGC

Software

• BIOS, Drivers, and Operating System Installation

A. Confirm BIOS Version: Look on the Server/System Management screen in the BIOS

Setup Utility to determine the installed BIOS version. Compare this to the versions at:

http://www.intel.com/support/motherboards/server.

If new versions are available, update the BIOS on your server.

B. Configure your RAID Controller:

Use the instructions provided with the RAID controller.

C. Install your Operating System:

Use the instructions provided with the RAID controller

and with the operating system.

D. Install Operating System Drivers: With the operating system running, insert the

Intel

Server Deployment and Management DVD. If using a Microsoft Windows* operating system,

the Intel

Deployment Assistant will autorun and allow you to select the appropriate drivers to install.

On other operating systems, browse the DVD folders to locate and install the driver files.

Side 2

Locate the white 4-pin key header between Serial B port and Front

Panel USB port. Match the Key and connector orientation and press

down to install.

Install Add-in

Card (Optional)

See the documentation that came with your

server chassis for add-in card installation.

For the Intel

Server Chassis P4000 series,

see the Quick Installation User's Guide

accompanying the chassis.

Install TPM, RMM4 and

eUSB SSD (Optional)

See the Intel

Trusted Platform Module Hardware

User’s Guide for the TPM module installation.

See Intel

Remote Management Module 4 User

GUide for the RMM4 installation.

See the instructions come along with the eUSB SSD

device for eUSB SSD installation.

Finishing Up

CAUTION: See your chassis

documentation for AC power and

grounding requirements.

Network

USB 0

USB 1

USB 2

USB 3

NIC1

10/100/

1000 Mb

NIC2

10/100/

1000 Mb

NIC3

10/100/

1000 Mb

NIC4

10/100/

1000 Mb

Video

Serial A

Before installing your operating

system, you must finish your chassis

installation, make I/O connections and

plug in AC power.

See your chassis documentation for AC

power and grounding requirements.

Common Problems and Solutions

The system does not boot or show video at power-on.

•

Check that the +12V CPU power connector is plugged in. Without this cable, the processors will not have any power.

•

Only Intel

Xeon

Processor E5-2600 series

with 130 W and less Thermal Design Power (TDP) are supported on this server board.

Previous generation Intel

Xeon

processors are not supported.

Beep code 1-5-2-1 in a system means you do not have Intel

Xeon

Processor E5-2600 series

installed.

•

The system generates the memory error beep code and POST diagnostic LED message {0XE0~0XEF} that indicates memory errors in early POST .

•

Remember, all DIMMs must be:

•

DDR3 800/1066/1333/1600 MHz UDIMM/RDIMM/LRDIMM.

•

From the same manufacturer.

•

Installed beginning with DIMM A1.

For a list of hardware components that have been tested with

this system, see:

http://www.intel.com/support/motherboards/server

Main Power

Connector Detail

Latch

Tab

CPU Power

Connector Detail

Make Server Board

Power Connections

Attach the CPU 1 power connector.

Attach the CPU 2 power connector.

CAUTION:

Note the location of the

latch on each power cable

connector and align it with the matching

tab on each server board socket.

Attach the main power connector.

IMPORTANT NOTE:

If you are using a

non-Intel server chassis with an ATX

power supply, see the documentation

that came with your chassis for

installation information.

Connect Hard Drives/Optical Drive to

Server Board

Connect SAS/SATA Data Cables to server board here.

NOTE:

* Ports 0-3 are eanbled as SATA ports by

default. Optional Intel

RAID C600

Upgrade Key is required to support SAS

feature on ports 0-3, or additional

SATA/SAS ports 4-7.

** 6Gb/s SATA port.

SAS/SATA 0*

SAS/SATA 1*

SAS/SATA 2*

SAS/SATA 3*

SAS/SATA 4*

SAS/SATA 5*

SAS/SATA 6*

SAS/SATA 7*

Server

Board

SATA 1**

SATA 4

SATA 5

SATA 3

SATA 2

SATA 0**

Server

Board

System Fan 7

Connector

Detail

System Fan 1-6

Connector

Detail

Chassis Fan Connections

For a non-Intel server chassis, see the documentation accompanying your chassis for specific chassis

fan connection requirements. Refer to the "Making Connections to the Server Board - Quick Reference"

section below.

C1DIMM C2 D1 D2

B2DIMM B1 A2 A1

E1DIMM E2 F1 F2

H2DIMM H1 G2 G1

Memory Conﬁgurations and Population Order:

Note: For additional memory configurations, see the

Techinical Product Specification for Intel

Server

Board S2600CP at:

http://www.intel.com/support/motherboards/server.

Memory sizing and configuration is supported only for

qualified DIMMs approved by Intel

Memory Type: Minimum of one 1 GB,

DDR3 800/1066/1333/1600 MHz

UDIMM/RDIMM/LRDIMM.

Install DIMM Memory Modules

DDR3 DIMM Memory Identiﬁcation:

DIMM

notch and

socket

bump must

align as

shown.

Other

Memory

DDR3

This server board supports up to 16 DDR3 800/1066/1333/1600

UDIMM/RDIMM/LRDIMM.

CAUTION: Observe normal ESD (ElectroStatic Discharge) procedures

to avoid possible damage to system components.

Install Optical

Drive and

Hard Drive(s)

See the documentation that came

with your server chassis for drive

installation.

Making Connections to the Server Board — Quick Reference

Attach Front Panel, Serial, and USB Connections

Note: For a non-Intel

chassis, see your

chassis documentation

for front panel features

and server board

connection requirements.

Internal

USB/Serial

Connector

Detail

Serial B

USB

Front Panel

USB

Connector

Detail

Front Panel

Connector

Detail

Connect When

NIC3/NIC4

Ports Available

Install Intel® RAID C600

Upgrade Key (Optional)

Server Board

Power

Supply

CPU2 CPU1

Main Power

Front

Panel

SAS/SATA*

USB

FAN_2

FAN_1

Server Board

Power Supply

CPU2 CPU1

Main Power

Front

Panel

SAS/SATA*

SGPIO**

HSBP_I

USB

PMBus

FAN_3

FAN_4

FAN_5

FAN_2

FAN_1

STOR_UPG_KEY

= Make this connection

Intel

Server Chassis

P4000 series

A. CPU 1-2 Power Connector

B. Main Power Connector

C. Front Panel Header

Required Connections

Intel

Server Chassis

P4000 series

Optional Connections

D. System Fan 1 Header

E. System Fan 2 Header

F. System Fan 3 Header

G. System Fan 4 Header

H. System Fan 5 Header

I. System Fan 6 Header

J. System Fan 7 Header

K. CPU 1 Fan Header

L. CPU 2 Fan Header

M. Serial B

N. Storage Upgrade Key

O. USB (Front Panel)

P. IPMB

Q. SAS/SATA Connectors

1. SATA 6G R2. SATA 3G

S. RMM4 Lite

T. Chassis Intrusion

U. RMM4 NIC

V. HSBP_I

X. SATA SGPIO

Y. eUSB SSD

Z. TPM

AA. USB (Type A)

AB. LCP

AC. PMBus

W. SAS SGPIO

IMPORTANT Note:

Cables should be

tied for better airflow.

Use cable-ties as necessary.

Note: For a non-Intel Chassis, see your chassis documentation

for server board connection information.

Note: Not all optional connections are shown in this diagram.

Refer to your Server Board Service Guide, and your server

chassis documentation for additional connection information.

Cable Routing with Fixed Fans, Fixed HDDs, Fixed PSU Cable Routing with Hotswap Fans, backplane(s), redundant PSU(s)

Note: Make CPU

FAN connections

if necessary.

CPU1/CPU2 Power Cable

Server Board Main Power Cable

Backplane Power Cable

ODD Power Cable

Front Panel Cable, USB Cable

ODD Data Cable (Connect To White SATA 6G

Connectors On Server Board)

MiniSAS and SGPIO

PMBus Cable

HSBP_I2C Cable (From Server Board To First

Backplane)

HSBP_I2C Cable (From First Backplane To Second

Backplane when Second Backplane Available)

System FAN 1

System FAN 2

System FAN 3

System FAN 4

System FAN 5

ODD Data Cable (Connect To White

SATA 6G Connectors On Server Board)

Fixed HDD Data Cable

System FAN 1

System FAN 2

CPU1/CPU2 Power Cable

Server Board Main Power Cable

Fixed HDD Power Cable

ODD Power Cable

Front Panel Cable, USB Cable

Make the connections with fixed fans

Make the connections with hotswap fans, backplane(s), power supply(s)

Make the connection when applicable

Front Panel

SAS/SATA

USB

IPMB

HSBP_I

CPU 1 Power

CPU 2 Power

Chassis Intrusion

RMM4 Lite

RMM4 NIC

SAS SGPIO

TPM

Main Power

Sys Fan 2

Sys Fan 1

USB

PMBus

LCP

Serial B

eUSB SSD

CPU 1 Fan

CPU 2 Fan

Sys Fan 4

Sys Fan 3

Sys Fan 6

Sys Fan 5

Sys Fan 7

Storage Upgrade Key

DIMM E1

DIMM E2

DIMM F1

DIMM F2

DIMM H2

DIMM H1

DIMM G2

DIMM G1

DIMM B2

DIMM B1

DIMM A2

DIMM A1

DIMM C1

DIMM C2

DIMM D1

DIMM D2

SATA

SATA SGPIO

Summary of content (1 pages)

PAGE 1
8 Install DIMM Memory Modules Memory Conﬁgurations and Population Order: CAUTION: Observe normal ESD (ElectroStatic Discharge) procedures to avoid possible damage to system components. Memory Type: Minimum of one 1 GB, DDR3 800/1066/1333/1600 MHz UDIMM/RDIMM/LRDIMM. This server board supports up to 16 DDR3 800/1066/1333/1600 UDIMM/RDIMM/LRDIMM. DIMM E1 E2 F1 F2 Note: For additional memory configurations, see the Techinical Product Specification for Intel® Server Board S2600CP at: http://www.intel.