Quick Installation Guide Part 2

ManualsBrandsIntel ManualsOtherIntel Server System P4308CP4MHGC

General Installation Process

The installation instructions in this section are for general components of Intel® Server Chassis

P4000M family, but the illustrations are based on the Intel® Server Chassis P4308XXMFEN.

Minimum Hardware Requirements

To avoid integration difficulties and possible

damage to your system, make sure you

have components from each category below.

■ Processor

■ Heat Sink

■ Memory

■ Hard Disk Drives

■ Power

■ Air Duct

Remove the Bezel Assembly

At a 40-degree angle, push the bezel assembly away from

the chassis.

Release the two plastic tabs on the left side of the bezel assembly to

disengage the tabs, and rotate the bezel assembly no more than 40

degrees outward.

CAUTION: Do not rotate the bezel assembly more than 40° or you will

damage the bezel hooks at the right side of the bezel assembly.

Remove the Side Cover

Remove the screws.

Note:

A non-skid surface or a stop behind the

chassis may be needed to prevent the

chassis from sliding on your work surface.

Slide the side cover back and lift the cover

outward to remove it.

Install Server Board

• See your Intel

Server Board Quick

Start User’s Guide for server board

installation instructions and installation of

the back panel I/O shield.

• Use the mounting screws, bumpers and

standoffs (if necessary) that come with

your chassis to secure the server board to

the chassis.

Return to this document when finished.

Press the clip.

B. Install the Hard Disk Drive C. Install the EMI shield

Secure the 3.5" or 2.5"

HDD on the HDD carrier

tray with screws.

Pull out the HDD

carrier tray.

Insert the HDD carrier

tray into chassis.

Press the clip.

Fit the edges of the EMI Shield against

the sides of the chassis.

A. Remove the EMI

shield

Lift the EMI shield and

move EMI shield outward

from the chassis.

3.5" HDD

2.5" HDD

Install Hard Drive

Fixed Hard Drive Carrier (For chassis with ﬁxed hard drive bay only)

Slide the EMI Shield downwards until

the latches on the EMI Shield are

engaged with the chassis.

Summary of content (11 pages)

PAGE 1
General Installation Process The installation instructions in this section are for general components of Intel® Server Chassis P4000M family, but the illustrations are based on the Intel® Server Chassis P4308XXMFEN. 1 Minimum Hardware Requirements To avoid integration difficulties and possible damage to your system, make sure you have components from each category below. Processor Heat Sink Memory Hard Disk Drives Power Air Duct ■ ■ ■ ■ ■ ■ 2 Remove the Side Cover A Remove the screws.
PAGE 2
General Installation Process Install Hard Drive ... Continued 2.5" Hot-Swap Hard Drive Carrier (For chassis with 2.5" hot-swap hard drive bay only) D F D HD 5" 2. D E C B A A Remove the drive carrier by pressing the green button and opening the lever. B Slide the carrier out. C Remove the four screws securing the plastic retention device to the 2.5" HDD carrier. D Disengage the plastic retention device from the HDD carrier slides by pulling the slides.
PAGE 3
General Installation Process Install Hard Drive ... Continued Install 2.5" Hard Drive into 3.5" Hot-swap Hard Drive Carrier as option: d1 AB NG F T TI E OF OU IV K M DR EA RE RD BR EFO HA B 5´ ´ 2. 2.5" d4 HDD 2.5" P TO Bo Viewttom d3 HDD d2 d1 Break off the tab on the HDD interface bracket. 5 d2 Install the HDD interface bracket from d4 Secure the hard disk drive using d3 Slide the 2.5" HDD into the bracket to top. Secure the bracket with three screws as shown.
PAGE 4
General Installation Process 7 8 Complete Server Board Cabling Connections A B Install PCI-e Card Assembly C Remove the PCI-e slot shield by pushing the shield out from inside the chassis. Install the optional PCI-e card fixture with screws. The card fixture helps to hold heavy PCI-e cards (i.e GPGPU card). The card fixture is ordered seperately. Rotate the PCI-e retainer all the way to open.
PAGE 5
General Installation Process 9 Install Intel® Remote Management Module 4 NIC (optional) Top Server Board D View Chassis Back Opening Serve Boardr B Filler A A A B C E RMM NIC C4 onnec tor ® Attach the metal fastening bracket to Intel Dedicated Server Management NIC module and secure the bracket with two screws. Remove the alternate RMM4 knock out by pressing the knock out from inside the chassis.
PAGE 6
General Installation Process 12 Install Intel® RAID Smart Battery (optional) A Align the tabs on the plastic battery holder with the mounting holes in the chassis and slide the plastic battery holder toward the front of the chassis until the tabs engage with the mounting holes. A 13 Install Second Power Supply Module (optional) Note: Applies only to the chassis with hot-swap power supply configuration. Latch Finger Hole A A Use the 'finger hole' to remove the filler panel.
PAGE 7
General Installation Process 16 Reinstall Front Bezel Assembly A Engage three plastic bezel hooks into the raised metal slots at the chassis edge. Keep the right edge of front bezel align tightly with the right edge of the Chassis. B Rotate the bezel assembly toward the chassis and latch the two plastic tabs on the left side of the bezel assembly to the chassis. 17 Install Feet (pedestal only) Note: This step applies to your chassis if configured as a pedestal system.
PAGE 8
General Installation Process 20 Finishing Up 21 Install Software • BIOS, Drivers, and Operating System Install ® 1. See your Intel Server Board Quick Start User's Guide to connect your keyboard, mouse, video, and other I/O cables. A. Conﬁrm BIOS Version: Look on the Server/System Management screen in the BIOS Setup Utility to determine the installed BIOS version. Compare this to the versions at: http://www.intel.com/support If new versions are available, update the BIOS on your server.
PAGE 9
Reference HDD Cage Cable Connection Note: Refer to the documentation that came with your server board and/or RAID controller card for instructions on connecting backplane cables to your server board or RAID controller card. 4 x 3.5" HDD Cage 8 x 3.5" HDD Cage C A B HDD0 HDD1 HDD2 HDD3 C B D A A B C D Connect the I2C cable to I2C_IN connector on backplane. A B C Connect the SATA data cables. Connect power cable. Connect SGPIO cable. Connect the I2C cable to I2C connector on backplane.
PAGE 10
Reference Front Panel Controls and Indicators I A B A Reservation(Optional VGA/Serial Port) B USB Connectors C ID Button with ID LED Integrated C D E F G H D NMI Button E NIC LED F System Reset Button G System Status LED H System Power Button with Power LED I HDD Activity LED Hot Swap Hard Drive Bay Options and HDD Numbering 3 2 1 0 4 x 3.5" Hot-Swap Drive Cage 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 8 x 3.5" Hot-Swap Drive Cage 8 x 2.
PAGE 11
G30108-004