Intel® Server System R1000JP Family Technical Product Specification Intel order number: G71652-008 Revision 1.
® Revision History IntelP P Server System R1000JP Family TPS Revision History Date Revision Number Modifications November, 2012 0.5 Initial release. December, 2012 1.0 Updated assembly information of the optical drive. May, 2013 1.1 Update pin-out table for Power Distribution Board July, 2013 1.2 Update LED Indications table for 450W AC and 750W AC PSU Sep, 2013 1.3 October, 2013 1.4 November, 2013 1.5 March, 2014 1.6 April, 2014 1.7 Add E5-2600 and E5-1600 V2 CPU support.
® IntelP P Server System R1000JP Family TPS Disclaimers Disclaimers INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT.
Table of Contents ®P IntelP Server System R1000JP Family TPS Table of Contents 1. Introduction ........................................................................................................................1 1.1 Chapter Outline ......................................................................................................1 1.2 Server Board Use Disclaimer .................................................................................1 2. Product Overview ................................
® IntelP P Server System R1000JP Family TPS Table of Contents 4.2.3 Set Fan Profile .....................................................................................................37 4.2.4 Fan PWM Offset...................................................................................................37 4.2.5 Quiet Fan Idle Mode .............................................................................................37 4.2.6 Thermal Sensor Input for Fan Speed Control ............................
Table of Contents ®P IntelP Server System R1000JP Family TPS 9.2 Riser Card Options – Riser Slot #1.......................................................................64 9.3 Riser Card Options – Riser Slot #2.......................................................................64 9.4 Riser Card Options – Riser Slot #3.......................................................................66 Appendix A: Integration and Usage Tips ........................................................................
® IntelP P Server System R1000JP Family TPS List of Figures List of Figures Figure 1. Product Drawing ..........................................................................................................3 Figure 2. System Photo...............................................................................................................6 Figure 3. Chassis Dimension ......................................................................................................7 Figure 4.
List of Figures ®P IntelP Server System R1000JP Family TPS Figure 40. LCP Background color during an error .....................................................................56 Figure 41. LCP Main Menu .......................................................................................................56 Figure 42. LCP Event Menu ......................................................................................................57 Figure 43. LCP View Menu ..........................................
® IntelP P Server System R1000JP Family TPS List of Tables List of Tables Table 1. System Feature Set.......................................................................................................3 Table 2. System SKU matrix .......................................................................................................5 Table 3. System Environmental Limits Summary ........................................................................7 Table 4.
List of Tables ®P IntelP Server System R1000JP Family TPS Table 40. Dedicated NIC Port LED Functionality .......................................................................65 Table 41. POST Progress Code LED Example .........................................................................69 Table 42. Diagnostic LED POST Code Decoder .......................................................................70 Table 43. MRC Progress Codes ..................................................................
® IntelP P Server System R1000JP Family TPS List of Tables xi Revision 1.
® IntelP P Server System R1000JP Family TPS 1. Introduction Introduction This Technical Product Specification (TPS) provides system specific information detailing the features, functionality, and high-level architecture of the Intel® Server System R1000JP family. You should also reference the Intel® Server Board S1600JP Family Technical Product Specification to obtain greater detail of functionality and architecture of the server board integrated in this server system.
Introduction ® IntelP P Server System R1000JP Family TPS does not operate correctly when used outside any of their published operating or non-operating limits. 2 Revision 1.
® IntelP P Server System R1000JP Family TPS 2. Product Overview Product Overview This generation of Intel® 1U server platforms offers a variety of system options to meet the varied configuration requirements of high-density high-performance computing environments. The Intel® Server System R1000JP product family is comprised of several available 1U rack mount server systems that are all integrated with an Intel® Server Board S1600JP4. This chapter provides a high-level overview of the system features.
® Product Overview IntelP P Server System R1000JP Family TPS Feature /Headers System Fan Support Add-in Adapter Support Description Four RJ-45 Network Interface for 10/100/1000 LAN Two USB 2.0 connectors Internal connectors/headers: One Type A USB connector Two 2 x 5 USB connectors One 2 x 5 serial port connector One internal video connector for the front video Six SATA connectors One mini SAS connector Four fans for R1208JP4OC, R1304JP4OC, R1208JP4TC, and R1304JP4TC.
® IntelP P Server System R1000JP Family TPS Product Overview Table 2. System SKU matrix Board SKU vs Chassis 3.5” HDD 450W AC R1304JP4OC 450W DC R1304JP4TC 750W AC R1304JP4GS 2.5” HDD R1208JP4OC R1208JP4TC R1208JP4GS The Intel® Server System R1000JP family are supporting all Intel® Xeon® processor E5-2600 series with TDP 135W (8-core, 6-core), or 80W (4-core) and below. You can find a full list of supported processors at the Intel® Support website: http://www.intel.
Product Overview 2.1 ® IntelP P Server System R1000JP Family TPS System Views Figure 2. System Photo 2.2 System Dimensions 6 Revision 1.
® IntelP P Server System R1000JP Family TPS Product Overview Figure 3. Chassis Dimension 2.3 System Level Environmental Limits The following table defines the system level operating and non-operating environmental limits. Table 3. System Environmental Limits Summary Parameter Limits Temperature Operating ASHRAE Class A2 – Continuous Operation. 10ºC to 35ºC (50ºF to 95ºF) with the maximum rate of change not to exceed 10°C per hour. Shipping -40ºC to 70ºC (-40ºF to 158ºF).
® Product Overview IntelP P Server System R1000JP Family TPS Parameter Limits Humidity Shipping 50% to 90%, non-condensing with a maximum wet bulb of 28°C (at temperatures from 25°C to 35°C). Operating Half sine, 2g, 11 mSec. Unpackaged Trapezoidal, 25 g, velocity change is based on packaged weight. Packaged Product Weight: ≥ 40 to < 80. Non-palletized Free Fall Height = 18 inches. Palletized (single product) Free Fall Height = NA. Unpackaged 5 Hz to 500 Hz 2.20 g RMS random.
® IntelP P Server System R1000JP Family TPS 2.4 Product Overview System Features and Options Overview Figure 4. System Components Overview 2.4.1 Hot Swap Hard Drive Bay and Front Panel Options Figure 5. 3.5" Hard Drive Bay - 4 Drive Configuration Figure 6. 2.5" Hard Drive Bay - 8 Drive Configuration Revision 1.
® Product Overview 2.4.2 IntelP P Server System R1000JP Family TPS Back Panel Features Figure 7. Back Panel Feature Identification (Redundant Power Supply as shown) 2.4.
® IntelP P Server System R1000JP Family TPS Product Overview ® Figure 9. Intel Server Board S1600JP4 Revision 1.
® Product Overview 2.5.1 IntelP P Server System R1000JP Family TPS Rear Component View The following figure shows the layout of the server board. Each connector and major component is identified. The description is given below in the figure. A ID LED Description F Description Two NIC ports (RJ45) B 5V standby LED G USB connector C DB15 Video out H Diagnostic LED D Two NIC ports (RJ45) I USB connector E System status LED ® Figure 10. Intel Server Board S1600JP Components 2.
® IntelP P Server System R1000JP Family TPS 2.
® Power Sub-System 3. IntelP P Server System R1000JP Family TPS Power Sub-System This chapter will provide a high level overview of the power management features and specification data for the power supply options available for this server product. Specification variations will be identified for each supported power supply. There are three power supply options available in Intel® Server System R1000JP Family: 450W AC, 450W DC, and 750W AC.
® IntelP P Server System R1000JP Family TPS Power Sub-System Figure 14. 450W AC Power Supply Unit Dimension Overview Figure 15. 450W AC Power Supply – Connector View 3.1.2 Power Supply Output Connectors This 450W AC power supply module has 2x14 card edge output connection that plugs directly into a matching slot connector on power distribution board. The connector provides both power and communication signals. The following Table 4 defines the connector pin-out. Revision 1.
® Power Sub-System IntelP P Server System R1000JP Family TPS Figure 16. 450W Power Supply Module Output Power Connector Table 4.
® IntelP P Server System R1000JP Family TPS Power Sub-System AC present / Only 5VSB on (PS off) 1Hz Blink GREEN AC cord unplugged or AC power lost; with a second power supply in parallel still with AC input power Power supply warning events where the power supply continues to operate; high temp, high power, high current, slow fan. Power supply critical event causing a shutdown; failure, OCP, OVP, Fan Fail AMBER 1Hz Blink Amber AMBER 3.1.
® Power Sub-System IntelP P Server System R1000JP Family TPS Table 8. AC Input Voltage Range PARAMETER MIN RATED VMAX Voltage (110) 90 Vrms 100-127 Vrms 140 Vrms Voltage (220) 180 Vrms 200-240 Vrms 264 Vrms Frequency 47 Hz 50/60 63 Hz Start up VAC 85VAC +/4VAC Power Off VAC 70VAC +/5VAC Notes: 1. 2. 3. 3.1.6.3 Maximum input current at low input voltage range shall be measured at 90VAC, at maximum load.
® IntelP P Server System R1000JP Family TPS Power Sub-System line. Half cycle peak inrush current, peak repetitive input current, and worse case power factor must be provided by the vendor to assist with the UPS and line conditioning, sizing, and selection. No component will be stressed over its Max Specification (I 2·t). This must be demonstrated through measurements of the critical component specifications. 3.1.6.
® Power Sub-System IntelP P Server System R1000JP Family TPS A The apparatus shall continue to operate as intended. No degradation of performance. B The apparatus shall continue to operate as intended. No degradation of performance beyond spec limits. C Temporary loss of function is allowed provided the function is self-recoverable or can be restored by the operation of the controls. 3.1.6.
® IntelP P Server System R1000JP Family TPS Power Sub-System must meet only the static load voltage regulation requirements for the minimum static load conditions. Table 12. Load Ratings +12V +5VSB MAX 36.26A 3A MIN DYNAMIC 2A 0.5A MIN STATIC 0.5A 0.1A *The combined output power of all outputs shall not exceed 405W @100~127VAC. 3.1.7.2 Standby Output The 5VSB output should be present when an AC input greater than the power supply turn on voltage is applied. 3.1.
® Power Sub-System 3.1.8.3 IntelP P Server System R1000JP Family TPS +12 V 13.6V ~ 15.0V 5VSB 5.6V ~ 6.5V Over Temperature Protection (OTP) The power supply will be protected against over temperature conditions caused by loss of fan cooling or excessive ambient temperature. In an OTP condition, the PSU will shut down. When the power supply temperature drops to within specified limits, the power supply will restore power automatically, while the 12VSB remains always on.
® IntelP P Server System R1000JP Family TPS Power Sub-System 3.2 750W AC Power Supply In Intel® Server System R1304JP4GS and R1208JP4GS, there is a single 750W power supply integrated. The parameters of this power supply are defined in below paragraph. 3.2.1 Mechanical Overview The physical size of the power supply enclosure is 39/40mm x 73.5mm x 185mm. The power supply contains a single 40mm fan. The power supply has a card edge output that interfaces with a 2x25 card edge connector in the system.
® Power Sub-System IntelP P Server System R1000JP Family TPS Figure 20. 750W AC Power Supply – Connector View 3.2.2 Connectors on Power Distribution Board The power supply shall use a card edge output connection for power and signal that is compatible with a 2x25 Power Card Edge connector. Table 15.
® IntelP P Server System R1000JP Family TPS Power Sub-System Table 16. Output Power Connector 1 J2A2 Pin-out Pin 10 Name +12V1 Pin 11 Name GND 9 +12V1 12 GND 8 +12V1 13 GND 7 +12V1 14 GND 6 +12V1 15 GND 5 +12V1 16 GND 4 +5V 17 GND 3 +5V 18 GND 2 +3.3V 19 GND 1 +12V2 20 +12V2 Table 17. Output Power Connector 2 J1B1 Pin-out Pin 1 Name PSON# Pin 10 Name +5V stby 2 GND 11 PWOK 3 GND 12 +3.3V 4 GND 13 +3.
® Power Sub-System IntelP P Server System R1000JP Family TPS Table 20. 750 Watt AC Power Supply Efficiency Loading Minimum Efficiency 100% of maximum 91% 50% of maximum 94% 20% of maximum 90% 10% of maximun 82% 3.2.4 Power Cord Specification Requirements Power cords used must meet the specification requirements listed in the following table: Table 21. AC Power Cord Specifications Cable Type SJT Wire Size 16 AWG Temperature Rating 105ºC Amperage Rating 13 A Voltage Rating 125 V Figure 21.
® IntelP P Server System R1000JP Family TPS Power Sub-System 3.2.6 AC Input Requirement 3.2.6.1 Power Factor The power supply must meet the power factor requirements stated in the Energy Star® Program Requirements for Computer Servers. These requirements are stated below: Output power 10% load 20% load 50% load 100% load Power factor > 0.65 > 0.80 > 0.90 > 0.95 Note: Tested at 230Vac, 50Hz and 60Hz, and 115VAC, 60Hz.
® Power Sub-System 3.2.6.5 IntelP P Server System R1000JP Family TPS AC Line Dropout/Holdup An AC line dropout is defined to be when the AC input drops to 0VAC at any phase of the AC line for any length of time. During an AC dropout, the power supply must meet dynamic voltage regulation requirements. An AC line dropout of any duration shall not cause tripping of control signals or protection circuits.
® IntelP P Server System R1000JP Family TPS Power Sub-System 0 to 1/2 AC cycle 95% Nominal AC Voltage ranges 50/60Hz No loss of function or performance > 1 AC cycle >30 % Nominal AC Voltage ranges 50/60Hz Loss of function acceptable, self recoverable Table 25. AC Line Surge Transient Performance Duration Continuous Surge 10% Operating AC Voltage Nominal AC Voltages 0 to ½ AC cycle 30% Mid-point of nominal AC Voltages 3.2.6.
® Power Sub-System IntelP P Server System R1000JP Family TPS The pass criteria include: No unsafe operation is allowed under any condition All power supply output voltage levels to stay within proper spec levels No change in operating state or loss of data during and after the test profile No component damage under any condition The power supply shall comply with the limits defined in EN55024: 1998/A1: 2001/A2: 2003 using the IEC 61000-4-5: Edition 1.
® IntelP P Server System R1000JP Family TPS 3.2.6.19 Power Sub-System AC Line Isolation Requirements The power supply shall meet all safety agency requirements for dielectric strength. Additionally, power supply vendor must provide Intel® with written confirmation of dielectric withstand test which includes: voltage level, duration of test, and identification detailing how each power supply is marked to indicate dielectric withstand test had been completed successfully.
® Power Sub-System IntelP P Server System R1000JP Family TPS voltage dropping below nominal voltage conditions. “Surge” will be defined to refer to conditions when the AC line voltage rises above nominal voltage. The power supply shall meet the requirements under the following AC line sag and surge conditions. Table 28.
® IntelP P Server System R1000JP Family TPS Power Sub-System Notes: 1. 12Vstby must provide 4.0A with two power supplies in parallel. The fan may work when stby current >1.5A 2. Length of time peak power can be supported is based on thermal sensor and assertion of the SMBAlert# signal. Minimum peak power duration shall be 20 seconds without asserting the SMBAlert# signal at maximum operating temperature. 3.2.7.2 Pmax Power support The PSU should support 3msec peak power duration at a 50msec period; 5.
® Power Sub-System IntelP P Server System R1000JP Family TPS Table 33. Over Voltage Protection (OVP) Limits Output Voltage 3.2.8.3 MIN (V) MAX (V) +12V 13.0 14.5 +12VSB 13.3 14.5 Over Temperature Protection (OTP) The power supply will be protected against over temperature conditions caused by loss of fan cooling or excessive ambient temperature. In an OTP condition the PSU will shut down.
® IntelP P Server System R1000JP Family TPS 4. Thermal Management Thermal Management The fully integrated system is designed to operate at external ambient temperatures of between 10ºC- 35ºC with limited excursion based operation up to 35ºC, as specified in Table 3..
® Thermal Management 4.2 IntelP P Server System R1000JP Family TPS Thermal Management Overview In order to maintain the necessary airflow within the system, all of the previously listed components and top cover need to be properly installed. For best system performance, the external ambient temperature should remain below 35ºC and all system fans should be operational. The system is designed for fan redundancy when the system is configured with two power supplies.
® IntelP P Server System R1000JP Family TPS Thermal Management [SOLTT] – Static Open Loop Thermal Throttling: for the DIMMs without sensor on DIMM (SOD). 4.2.2 Altitude This option is used to select the proper altitude that the system will be used in. Available settings include: [300m or less], [301m-900m], [901m-1500m], [Above 1500m].
® Thermal Management Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9.
® IntelP P Server System R1000JP Family TPS Thermal Management Figure 23. System Fan Identification Each system fan is mounted inside its own plastic fan housing which include rotational vibration dampening features. The fan assemblies are held in place by fitting them over mounting pins coming up from the chassis base. Figure 24. Removing a System Fan The system fan assembly is designed for ease of use and supports several features. System fans are NOT hot-swappable.
® Thermal Management IntelP P Server System R1000JP Family TPS Each fan has a tachometer signal that allows the integrated BMC to monitor its status. Each fan has a10-pin wire harness that connects to a matching connector on the server board. Figure 25. Server Board System Fan Connector Locations Table 34.
® IntelP P Server System R1000JP Family TPS 4.4 Thermal Management FRUSDR Utility The purpose of the embedded platform management and fan control systems is to monitor and control various system features, and to maintain an efficient operating environment. Platform management is also used to communicate system health to supported platform management software and support mechanisms.
System Storage and Peripheral Options 5. ®P IntelP Server System R1000JP Family TPS System Storage and Peripheral Options The Intel® Server System R1000JP product family has support for many storage device options, including: Hot Swap 2.5” Hard Disk Drives Hot Swap 3.5” Hard Disk Drives SATA Optical Drive Support for different storage and peripheral device options will vary depending on the system SKU. This section will provide an overview of each available option. 5.1 2.
®P IntelP Server System R1000JP Family TPS System Storage and Peripheral Options Table 36. Drive Activity LED States Condition Power on with no drive activity Power on with drive activity Green Power on and drive spun down Power on and drive spinning up Drive Type SAS LED stays on Behavior SATA LED stays off SAS LED blinks off when processing a command SATA LED blinks on when processing a command SAS LED stays off SATA LED stays off SAS LED blinks SATA LED stays off 5.1.1 2.
®P System Storage and Peripheral Options IntelP Server System R1000JP Family TPS 5.1.2 Cypress* CY8C22545 Enclosure Management Controller The backplane supports enclosure management using a Cypress* CY8C22545 Programmable System-on-Chip (PSoC*) device. The CY8C22545 drives the hard drive activity/fault LED, hard drive present signal, and controls hard drive power-up during system power-on. 5.2 3.5” Hard Disk Drive Support The server is available with support for four 3.
®P IntelP Server System R1000JP Family TPS 5.2.1 3.5” Drive Hot-Swap Backplane Overview System Storage and Peripheral Options On the front side of each back plane are mounted four hard disk drive interface connectors (A), each providing both power and I/O signals to attached hard disk drives. Figure 32. The front side of 4 x 3.5” Hotswap Backplane On the backside of each backplane are several connectors. The following illustration identifies each.
System Storage and Peripheral Options ®P IntelP Server System R1000JP Family TPS 5.2.2 Cypress* CY8C22545 Enclosure Management Controller The backplanes support enclosure management using a Cypress* CY8C22545 Programmable System-on-Chip (PSoC*) device. The CY8C22545 drives the hard drive activity/fault LED, hard drive present signal, and controls hard drive power-up during the system power-on. 5.
Storage Controller Options Overview ® IntelP P Server System R1000JP Family TPS 6 Storage Controller Options Overview The server platform supports many different embedded and add-in SATA/SAS controller to provide a large number of possible storage configurations. This section will provide an overview of the different options available. 6.
®P IntelP Server System R1000JP FamilyTPS Storage Controller Options Overview The following table identifies available upgrade key options and their supported features. ® Table 37.
Storage Controller Options Overview ® IntelP P Server System R1000JP Family TPS 6.2.2 Intel® Rapid Storage Technology (RSTe)1 Features of the embedded software RAID option Intel® Rapid Storage Technology (RSTe) include the following: Software RAID with system providing memory and CPU utilization. Supported RAID Levels – 0, 1, 5, 10. o 4-Port SATA RAID 5 available standard (no option key required). o 8-Port SATA RAID 5 support provided with appropriate Intel® RAID C600 Upgrade Key.
®P IntelP Server System R1000JP FamilyTPS Front Control Panel and I/O Panel Overview 7 Front Control Panel and I/O Panel Overview On the front panel of all system configurations is a Control Panel providing push button system controls and LED indicators for several system features, and an I/O Panel providing USB ports and a video connector. This section describes the features and functions of both front panel options. 7.
® Front Control Panel and I/O Panel Overview Label IntelP P Server System R1000JP Family TPS Description System ID Button with Integrated LED Label F Description System Status LED B NMI Button (recessed, tool required for use) G Power/Sleep Button with Integrated LED C NIC-1 Activity LED H Hard Drive Activity LED D NIC-3 Activity LED I NIC-4 Activity LED E System Cold Reset Button J NIC-2 Activity LED A Figure 37.
®P IntelP Server System R1000JP FamilyTPS Front Control Panel and I/O Panel Overview Table 38. System Status LED State Definitions Color Off State System is not operating Criticality Not ready Green Solid on Ok Green ~1 Hz blink Degraded system is operating in a degraded state although still functional, or system is operating in a redundant state but with an impending failure warning 1. 2. 3. 4. Description System is powered off (AC and/or DC). System is in EuP Lot6 Off Mode.
Front Control Panel and I/O Panel Overview Color Amber State ~1 Hz blink Criticality Non-critical System is operating in a degraded state with an impending failure warning, although still functioning Amber Solid on Critical, nonrecoverable – System is halted ® IntelP P Server System R1000JP Family TPS Description Non-fatal alarm – system is likely to fail: 1.
®P IntelP Server System R1000JP FamilyTPS Front Control Panel and I/O Panel Overview Table 39. Power/Sleep LED Functional States State Power Mode LED Description Power-off Non-ACPI Off System power is off, and the BIOS has not initialized the chipset. Power-on Non-ACPI On System power is on. S5 ACPI Off Mechanical is off, and the operating system has not saved any context to the hard disk. S4 ACPI Off Mechanical is off. The operating system has saved context to the hard disk.
® ® Intel Local Control Panel IntelP P Server System R1000JP Family TPS 8 Intel® Local Control Panel The Intel® Local Control Panel option (Intel® Product Order Code – AXXLCPANEL) utilizes a combination of control buttons and LCD display to provide system accessibility and monitoring.
®P IntelP ® Server System R1000JP FamilyTPS Intel Local Control Panel When the system’s status is degraded, the corresponding active event will be displayed in place of the banner. During an error, the background color will be light amber in color. The LCD panel displays the event with the highest severity that is most recent and is currently active (that is, in an asserted state). For the case that there are multiple active events with the same severity, the most recent event will be displayed.
® ® Intel Local Control Panel 8.3 IntelP P Server System R1000JP Family TPS Event Menu In the “Event” menu, the LCD displays the following items. It displays all active error events in human readable text in chronological order. Informational events will not be displayed. There is no upper limit on the number of active events which can be displayed. The severity of the event will be indicated as either “Degraded”, “Non Fatal”, or “Fatal”. ^ | <- | -> | Figure 42.
®P IntelP Server System R1000JP FamilyTPS ® Intel Local Control Panel This is a leaf node and there is no further traversal below this menu. User can only go to the previous screen by selecting the item, “^”. This applies to all the items of “View” menu. 8.4.2 System Information (SysInfo) Selecting “SysInfo” item in the “View” menu displays the Server’s name, model, GUID, asset tag, and custom string. It is also a leaf node like above menu.
® ® Intel Local Control Panel IntelP P Server System R1000JP Family TPS ^ | DHCP (or Static) | IP Address: xxx.xxx.xxx.xxx | Subnet Mask: xxx.xxx.xxx.xxx | Gateway: xxx.xxx.xxx.xxx Figure 47. LCP – RMM4 IP Configuration 8.4.5 Power Selecting “Power” item in the “View” menu displays the amount of AC power drawn by the system in Watts. ^ | xx W Figure 48. LCP – Power consumed by the System currently 8.4.
®P IntelP Server System R1000JP FamilyTPS ® Intel Local Control Panel 8.5.2 BMC IP If the user selects “BMC IP” item in the “Config” menu, then the following options will be displayed. ^ | IP Source | IP Address | Subnet | Gateway Figure 52. LCP – BMC IP Configuration Menu Selection of the “IP Source” in the above menu, leads to the following screen. Based on the user’s selection in the following menu, the firmware sets the BMC IP source as either DHCP or Static. ^ | DHCP | Static Figure 53.
® ® Intel Local Control Panel IntelP P Server System R1000JP Family TPS 5. 6. Any further Left or Right buttons will decrement or increment the value at that position. Second Enter button at that position makes the cursor to be ready for moving left or right. Any further Left or Right moves the cursor to previous or next position respectively. 7. So, the Enter button is used to select a position at the first time and to leave the position at the second time.
®P IntelP Server System R1000JP FamilyTPS ® Intel Local Control Panel ^ | Server Name | Server Model | Error | BMC IP | RMM4 IP | Power | Last PC | Custom String | Custom Logo Figure 57. Banner Configuration Menu Each of the menu items are explained below: Server Name: Displays the value specified in the product name in the product FRU information in the main board BMC FRU. The “Server Name” is the default banner.
® PCI Riser Card Support IntelP P Server System R1000JP Family TPS 9 PCI Riser Card Support Intel® Server System R1304JP4OC, R1208JP4OC, R1208JP4TC, and R1304JP4TC include two riser cards on the server board (Intel® Product Order code- F1UJP1X16RISER and F1UJP2X8RISER). Intel® Server System R1208JP4GS and R1304JP4GS include two riser cards too (Intel® Product Order code- F1UJP2X8RISER and F1UJPGPURISER). Riser cards for the server are NOT interchangeable between riser slots.
®P IntelP 9.2 Server System R1000JP FamilyTPS PCI Riser Card Support Riser Card Options – Riser Slot #1 All x16 PCIe bus lanes for Riser Slot #1 on the server board are routed from the processor. The riser card designed for Riser Slot #1 includes a single PCIe x16 (x16 lanes, x16 slot) add-in slot that can support a single low profile card. This card with Intel® Order product code F1UJP1X16RISER) is integrated in all of the Intel® Server System R1000JP family. Figure 59. 1U Riser Card #1 drawing 9.
® PCI Riser Card Support IntelP P Server System R1000JP Family TPS Figure 60. PCI Express* Riser with bracket and carrier board for Riser Slot 2 Figure 61. IOM Carrier The 1GbE port is dedicated NIC port for RMM4 Lite module. It only works once the RMM4 Lite module is installed in the system. The LED of dedicated NIC port is following the below definition: Table 40.
®P IntelP 9.4 Server System R1000JP FamilyTPS PCI Riser Card Support Riser Card Options – Riser Slot #3 All x16 PCIe bus lanes for Riser Slot #3 on the server board are routed from the processor. There are two options for Riser Slot #3. One option is to provide two slots in the riser with Intel® Product Order Code - F1UJP2X8RISER. The two slots in this riser provide one slot with x8 lanes x16 mechanical and one slot with x8 lanes and x8 mechanical.
PCI Riser Card Support ® IntelP P Server System R1000JP Family TPS Figure 63. 1U Riser drawing with bracket Please get the installation steps from the Intel® Server System R1000JP Family Service Guide to assemble the add-in video card. Revision 1.
®P IntelP Server System R1000JP FamilyTPS Appendix A: Integration and Usage Tips Appendix A: Integration and Usage Tips Before attempting to integrate and configure your system, you should reference this section, which provides a list of useful information. After the system is integrated with processors, memory, and peripheral devices, the FRUSDR utility must be run to load the proper Sensor Data Record data to the integrated Server Management subsystem.
® Appendix B: POST Code LED Decoder IntelP P Server System R1000JP Family TPS Appendix B: POST Code LED Decoder During the system boot process, the BIOS executes a number of platform configuration processes, each of which is assigned a specific hex POST code number. As each configuration routine is started, the BIOS displays the POST code to the POST Code Diagnostic LEDs on the back edge of the server board.
® IntelP P Server System R1000JP FamilyTPS Appendix B: POST Code LED Decoder Table 42. Diagnostic LED POST Code Decoder Diagnostic LED Decoder 1 = LED On, 0 = LED Off Checkpoint Upper Nibble Lower Nibble MSB LSB 8h 4h 2h 1h 8h 4h 2h 1h #7 #6 #5 #4 #3 #2 #1 #0 LED # Description SEC Phase 01h 0 0 0 0 0 0 0 1 First POST code after CPU reset. 02h 0 0 0 0 0 0 1 0 Microcode load begins. 03h 0 0 0 0 0 0 1 1 CRAM initialization begins. 04h 0 0 0 0 0 1 0 0 Pei Cache When Disabled.
Appendix B: POST Code LED Decoder Diagnostic LED Decoder 1 = LED On, 0 = LED Off Checkpoint Upper Nibble Lower Nibble MSB LSB 8h 4h 2h 1h 8h 4h 2h 1h #7 #6 #5 #4 #3 #2 #1 #0 LED # 9Bh 1 0 0 1 1 0 1 1 9Ch 1 0 0 1 1 1 0 0 9Dh 1 0 0 1 1 1 0 1 A1h 1 0 1 0 0 0 0 1 A2h 1 0 1 0 0 0 1 0 A3h 1 0 1 0 0 0 1 1 A4h 1 0 1 0 0 1 0 0 A5h 1 0 1 0 0 1 0 1 A6h 1 0 1 0 0 1 1 0 A7h 1 0 1 0 0 1 1 1 A8h 1 0 1 0 1 0 0 0 A9h 1 0 1 0 1 0 0 1 ABh 1 0 1 0 1 0 1 1 ACh 1 0 1 0 1 1 0 0 ADh 1 0 1 0 1 1 0 1 AEh 1 0 1 0 1 1 1 0 AFh 1 0 1 0
® IntelP P Server System R1000JP FamilyTPS Appendix B: POST Code LED Decoder Table 43.
® Appendix B: POST Code LED Decoder IntelP P Server System R1000JP Family TPS Diagnostic LED Decoder 1 = LED On, 0 = LED Off Checkpoint Upper Nibble Lower Nibble Description MSB 8h LED #7 LSB 4h #6 2h #5 1h #4 8h #3 4h #2 2h #1 1h #0 3h = No memory installed. All channels are disabled.
®P Appendix C: POST Code Errors IntelP Server System R1000JP Family TPS Appendix C: POST Code Errors Whenever possible, the BIOS outputs the current boot progress codes on the video screen. Progress codes are 32-bit quantities plus optional data. The 32-bit numbers include class, subclass, and operation information. The class and subclass fields point to the type of hardware being initialized. The operation field represents the specific initialization activity.
®P IntelP Server System R1000JP Family TPS Appendix C: POST Code Errors Error Code 8133 Processor 04 disabled Error Message Response Major 8160 Processor 01 unable to apply microcode update Major 8161 Processor 02 unable to apply microcode update Major 8162 Processor 03 unable to apply microcode update Major 8163 Processor 04 unable to apply microcode update Major 8170 Processor 01 failed Self Test (BIST) Major 8171 Processor 02 failed Self Test (BIST) Major 8172 Processor 03 fail
®P Appendix C: POST Code Errors IntelP Server System R1000JP Family TPS Error Code 8530 DIMM_F2 failed test/initialization Error Message Response Major 8531 DIMM_F3 failed test/initialization Major 8532 DIMM_G1 failed test/initialization Major 8533 DIMM_G2 failed test/initialization Major 8534 DIMM_G3 failed test/initialization Major 8535 DIMM_H1 failed test/initialization Major 8536 DIMM_H2 failed test/initialization Major 8537 DIMM_H3 failed test/initialization Major 8538 DIM
®P IntelP Server System R1000JP Family TPS Error Message Appendix C: POST Code Errors Error Code 8558 DIMM_J1 disabled Response Major 8559 DIMM_J2 disabled Major 855A DIMM_J3 disabled Major 855B DIMM_K1 disabled Major 855C DIMM_K2 disabled Major 855D DIMM_K3 disabled Major 855E DIMM_L1 disabled Major 855F (Go to 85D0) DIMM_L2 disabled Major 8560 DIMM_A1 encountered a Serial Presence Detection (SPD) failure Major 8561 DIMM_A2 encountered a Serial Presence Detection (SPD) fail
®P Appendix C: POST Code Errors IntelP Server System R1000JP Family TPS Error Code 85C0 DIMM_L3 failed test/initialization Error Message Response Major 85C1 DIMM_M1 failed test/initialization Major 85C2 DIMM_M2 failed test/initialization Major 85C3 DIMM_M3 failed test/initialization Major 85C4 DIMM_N1 failed test/initialization Major 85C5 DIMM_N2 failed test/initialization Major 85C6 DIMM_N3 failed test/initialization Major 85C7 DIMM_P1 failed test/initialization Major 85C8 DIM
®P IntelP Server System R1000JP Family TPS Appendix C: POST Code Errors Error Code 85E9 Error Message DIMM_P3 encountered a Serial Presence Detection (SPD) failure Response Major 85EA DIMM_R1 encountered a Serial Presence Detection (SPD) failure Major 85EB DIMM_R2 encountered a Serial Presence Detection (SPD) failure Major 85EC DIMM_R3 encountered a Serial Presence Detection (SPD) failure Major 85ED DIMM_T1 encountered a Serial Presence Detection (SPD) failure Major 85EE DIMM_T2 encounte
®P Appendix C: POST Code Errors IntelP Server System R1000JP Family TPS POST Error Beep Codes The following table lists POST error beep codes. Prior to system video initialization, the BIOS uses these beep codes to inform users on error conditions. The beep code is followed by a user-visible code on POST Progress LEDs. Table 46. POST Error Beep Codes Beeps 3 Error Message Memory error POST Progress Code Multiple Description System halted because a fatal error related to the memory was detected.
® Glossary IntelP P Server System R1000JP Family TPS Glossary Term ACPI Advanced Configuration and Power Interface AP Application Processor APIC Advanced Programmable Interrupt Control ASIC Application Specific Integrated Circuit ASMI Advanced Server Management Interface BIOS Basic Input/Output System BIST Built-In Self Test BMC Baseboard Management Controller Bridge Circuitry connecting one computer bus to another, allowing an agent on one to access the other BSP Bootstrap Processor
®P IntelP Server System R1000JP Family TPS Term Glossary Definition IP Internet Protocol IPMB Intelligent Platform Management Bus IPMI Intelligent Platform Management Interface IR Infrared ITP In-Target Probe KB 1024 bytes KCS Keyboard Controller Style LAN Local Area Network LCD Liquid Crystal Display LED Light Emitting Diode LPC Low Pin Count LUN Logical Unit Number MAC Media Access Control MB 1024KB MCH Memory Controller Hub MD2 Message Digest 2 – Hashing Algorithm MD
® Glossary IntelP P Server System R1000JP Family TPS Term Definition SEL System Event Log SIO Server Input/Output SMI Server Management Interrupt (SMI is the highest priority nonmaskable interrupt.
® IntelP P Server System R1000JP Family TPS Reference Documents Reference Documents Refer to the following documents for additional information: Intel® Server Board S1600JP Technical Product Specification ACPI 3.0: http://www.acpi.info/spec.htm IPMI 2.0 Data Center Management Interface Specification v1.0, May 1, 2008: www.intel.com/go/dcmi PCI Bus Power Management Interface Specification 1.1: http://www.pcisig.com/ PCI Express* Base Specification Rev 2.0, Dec 06: http://www.pcisig.
Reference Documents ® IntelP P Server System R1000JP Family TPS Platform Management FRU Information Storage Definition, Version 1.0, Revision 1.2, 2002. Intel Corporation, Hewlett-Packard Company, NEC Corporation, Dell Computer Corporation: http://developer.intel.com/design/servers/ipmi/spec.htm. 85 Revision 1.
