Intel® Server System R1000SP Product Family Technical Product Specification Intel order number G64249-002 Revision 2.
® Revision History Intel Server System R1000SP Product Family TPS Revision History Date Revision Number October, 2012 1.0 December, 2013 2.0 ii Modifications Initial release. • In Table 1, add a note that SAS Module and eUSB SSD can’t be supported at the same time. • Added support for Intel Xeon processor E5-2400 v2 product family • Updated chassis air flow specification ® Intel Order Number G64249-002 ® Revision 2.
® Intel Server System R1000SP Product Family Disclaimers Disclaimers INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT.
Table of Contents ® Intel Server System R1000SP Product Family TPS Table of Contents 1. Introduction ........................................................................................................................1 1.1 Chapter Outline ......................................................................................................1 1.2 Server Board Use Disclaimer .................................................................................1 2. Product Family Overview ....................
® Intel Server System R1000SP Product Family Table of Contents 4.5.1 Power Factor ........................................................................................................23 4.5.2 AC Input Voltage Specification .............................................................................23 4.5.3 AC Line Isolation Requirements ...........................................................................23 4.5.4 AC Line Dropout / Holdup .........................................................
Table of Contents ® Intel Server System R1000SP Product Family TPS 6.3.2 Cypress* CY8C22545 Enclosure Management Controller .................................... 41 6.4 Optical Drive Support ...........................................................................................41 6.5 SATA DOM Support .............................................................................................42 7. Storage Controller Options Overview .....................................................................
® Intel Server System R1000SP Product Family TPS List of Figures List of Figures Figure 1. Intel® Server System R1000SP ....................................................................................2 Figure 2. Intel® Server System R1000SP without Top Cover ......................................................3 Figure 3. Chassis Dimension (With Fixed Power Supply) ............................................................5 Figure 4. Chassis Dimension (With Hot Swap Power Supply) .................
List of Figures ® Intel Server System R1000SP Product Family TPS Figure 40. Install a SATA Optical Drive .....................................................................................41 Figure 41. Innodisk* SATA Disk-on-Module (DOM) device........................................................42 Figure 42. Intel® RAID C600 Upgrade Key Connector ...............................................................43 Figure 43. Front I/O Panel Features ....................................................
® Intel Server System R1000SP Product Family TPS List of Tables List of Tables Table 1. System Feature Set.......................................................................................................3 Table 2. System Environmental Limits Summary ........................................................................6 Table 3. Input Voltage Range....................................................................................................13 Table 4. 350W PSU Cable Lengths.................
List of Tables ® Intel Server System R1000SP Product Family TPS Table 40. Enabling Advanced Management Features ...............................................................62 Table 41. POST Progress Code LED Example .........................................................................65 Table 42. Diagnostic LED POST Code Decoder .......................................................................65 Table 43. MRC Progress Codes ....................................................................
® Intel Server System R1000SP Product Family TPS List of Tables Revision 2.
® Intel Server System R1000SP Product Family TPS 1. Introduction Introduction This Technical Product Specification (TPS) provides system level information for the Intel® Server System R1000SP product family. It describes the functions and features of the integrated server system which includes the chassis layout, system boards, power sub-system, cooling sub-system, storage sub-system options, and available installable options.
® Product Family Overview 2. Intel Server System R1000SP Product Family TPS Product Family Overview This generation of Intel® 1U server platforms offers a variety of system options to meet the varied configuration requirements of high-density high-performance computing environments. The Intel® Server System R1000SP product family is comprised of several available 1U rack mount server systems that are all integrated with an Intel® Server Board S1400SP.
® Intel Server System R1000SP Product Family TPS Product Family Overview ® Figure 2. Intel Server System R1000SP without Top Cover Table 1. System Feature Set Server System ® Intel Server System R1000SP product family Feature Processor Support Memory Chipset External I/O connections Internal I/O connectors/headers Revision 2.
® Product Family Overview Intel Server System R1000SP Product Family TPS Feature I/O Module Accessory Options Description The following I/O modules utilize a single proprietary on-board connector. An installed I/O module can be supported in addition to standard on-board features and any add-in expansion cards.
® Intel Server System R1000SP Product Family TPS 2.1 Product Family Overview Chassis Dimensions Figure 3. Chassis Dimension (With Fixed Power Supply) Revision 2.
Product Family Overview ® Intel Server System R1000SP Product Family TPS Figure 4. Chassis Dimension (With Hot Swap Power Supply) 2.2 System Level Environmental Limits The following table defines the system level operating and non-operating environmental limits. Table 2. System Environmental Limits Summary Parameter Limits Temperature Operating ASHRAE Class A2 – Continuous Operation.
® Intel Server System R1000SP Product Family TPS Product Family Overview Parameter Limits Operating Support operation up to 3050m with ASHRAE class deratings.
Product Family Overview ® Intel Server System R1000SP Product Family TPS See the Intel® S1400SP Product Family Power Budget and Thermal Configuration Tool for system configuration requirements and limitations. 2.3 System Features and Options Overview Figure 5. System Components Overview 2.3.1 Fixed Hard Drive Bay and Front Panel Options Figure 6. 3.5" Fixed Hard Drive Bay - 4 Drive Configuration 2.3.2 Hot Swap Hard Drive Bay and Front Panel Options Figure 7. 3.
® Intel Server System R1000SP Product Family TPS Product Family Overview Figure 8. 2.5" Hot Swap Hard Drive Bay - 8 Drive Configuration 2.3.3 Back Panel Features Figure 9. Back Panel Feature Identification Revision 2.
® Product Family Overview 2.3.4 Intel Server System R1000SP Product Family TPS Front Control Panel Options Label A Description System ID Button w/Integrated LED Label F Description System Status LED B NMI Button (recessed, tool required for use) G Power Button w/Integrated LED C NIC-1 Activity LED H Hard Drive Activity LED D NIC-3 Activity LED I NIC-4 Activity LED E System Cold Reset Button J NIC-2 Activity LED Figure 10. Front Control Panel Options 2.
® Intel Server System R1000SP Product Family TPS Product Family Overview ® Figure 12. Intel Light-Guided Diagnostic LED Layout 2.5 Available Front Bezel Support The optional front bezel is made of molded plastic and uses a snap-on design. When installed, its design allows for maximum airflow to maintain system cooling requirements. The face of the bezel assembly includes optional snap-in identification badge and wave (shown) features to allow for customization.
Product Family Overview ® Intel Server System R1000SP Product Family TPS Figure 14. Installing the Optional Front Bezel 2.
® Intel Server System R1000SP Product Family TPS 3. 350W Power Subsystem 350W Power Subsystem The power subsystem of the server systems consists of a single, non-redundant 350-W power supply with five outputs: 3.3 V, 5 V, 12 V, -12V and 5 VSB. The form factor fits into a 1U system and provides a wire harness output to the system. An IEC connector is provided on the external face for AC input to the power supply. The power supply provides one; non-redundant 40 mm fan for self-cooling.
® 350W Power Subsystem Intel Server System R1000SP Product Family TPS Figure 15. Power Supply Enclosure Drawing Note: All dimensions are in millimeters. 3.2 Output Connectors Listed or recognized component appliance wiring material (AVLV2), CN, rated min 80°C, 300 VDC should be used for all output wiring. Table 4.
® Intel Server System R1000SP Product Family TPS From Power Supply cover exit hole 3.2.1 Length (mm) 600 350W Power Subsystem To connector # P8 Description Mini SATA Drive Power Connector Baseboard power connector (P1) Table 5. P1 Main Power Connector Pin Signal +3.3VDC 3.3V S +3.3VDC GND +5VDC GND +5VDC GND PWR OK 5 VSB +12V 12VRS 1* 2 3 4 5 6 7 8 9 10* 18 AWG Color Orange Orange (24AWG) Orange Black Red Black Red Black Gray Purple Yellow Yellow/White (24AWG) Pin Signal +3.
® 350W Power Subsystem 3.2.4 Intel Server System R1000SP Product Family TPS Mini SATA Hard Drive Power Connectors (P8) Table 8. SATA Power Connector Pin 1 2 3 4 5 6 3.2.5 Signal 18 AWG Color N/C +5V +5V N/C GND GND N/C Red Red N/C Black Black AUX Power Connector (P3) Table 9. AUX Power Connector 1 Pin Signal SCL 24 AWG Color White/Green 2 3 SDA N/C White/Yellow N/C 3.2.6 4 Pin COM Signal 24 AWG Color White/Black 5 +3.3V White/Brown Hot-swap Backplane Power Connector (P7) Table 10.
® Intel Server System R1000SP Product Family TPS 3.4 350W Power Subsystem Marking and Identification The power supply module marking supports the following requirements: safety agency requirements; government requirements (if required; for example, point of manufacturing); power supply vendor requirements; and Intel® manufacturing and field support requirements. 3.5 Efficiency The power supply should have a recommended efficiency of 85% at maximum load and over the specified AC voltage. 3.
® 350W Power Subsystem 3.8.1 Intel Server System R1000SP Product Family TPS Over Current Protection (OCP) Each output must have individual OCP protection circuits. The PSU must shutdown and latch off after an over current condition occurs. Whereas OCP of +5VSB must turn the power supply into “hiccup mode” until the OCP condition removed. The values are measured at the PSU harness connectors and must not be damaged from repeated power cycling in this condition.
® Intel Server System R1000SP Product Family TPS 4. 450W Power Subsystem 450W Power Subsystem The power subsystem of the server systems consists of a redundant mini ERP 450-W power supply with 2 outputs: +12V and +5VSB. A separate PDB (power distribution board) is designed to plug directly to the output connector of the PS and provide additional power converters to produce other required voltages: +3.3V and +5V. An IEC connector is provided on the external face for AC input to the power supply.
® 450W Power Subsystem 4.1 Intel Server System R1000SP Product Family TPS Mechanical Overview Figure 18. Power Supply Module Mechanical Drawing Figure 19. Power Supply Module and Power Distribution Board Layout 4.2 Power Connectors on Power Distribution Board The power distribution board connects to the system through a wire harness. The harness size, connectors, and pin outs are shown below.
® Intel Server System R1000SP Product Family TPS 450W Power Subsystem Table 15.
® 450W Power Subsystem Intel Server System R1000SP Product Family TPS Table 19. Hot Swap Backplane Connector (P5) Pin 1 Signal COM 18 AWG color Black Pin 3 Signal +12V2 18 AWG Color Yellow/Black 2 COM Black 4 +12V Yellow/Black Table 20. SATA Peripheral Power Connectors (P6, P7, P8, P9) Pin 1 Signal +3.3VDC 18 AWG Color Orange 2 COM Black 3 +5VDC Red 4 COM Black 5 +12V2 Yellow/Black Table 21. Slim SATA Power Connector (P10) 4.
® Intel Server System R1000SP Product Family TPS 4.4 450W Power Subsystem Power Cord Specification Requirements Power cords used must meet the specification requirements listed in the following table. Table 23. AC Power Cord Specifications Cable Type Wire Size Temperature Rating Amperage Rating Voltage Rating SJT 16 AWG 105ºC 13 A 125 V Figure 20. AC Power Cord 4.5 AC Input Specifications 4.5.
® 450W Power Subsystem Intel Server System R1000SP Product Family TPS secondary dictates a higher dielectric strength test voltage the highest test voltage should be used. In addition, the insulation system must comply with reinforced insulation per safety standard IEC 950. Separation between the primary and secondary circuits, and primary to ground circuits, must comply with the IEC 950 spacing requirements. 4.5.
® Intel Server System R1000SP Product Family TPS 450W Power Subsystem Table 26. AC Line Surge Transient Performance Duration Continuous 0 to ½ AC cycle 4.5.
® 450W Power Subsystem 4.5.14 Intel Server System R1000SP Product Family TPS Voltage Interruptions The power supply must comply with the limits defined in EN55024: 1998/A1: 2001/A2: 2003 using the IEC 61000-4-11: Second Edition: 2004-03 test standard and performance criteria C defined in Annex B of CISPR 24. 4.6 Outputs Load Requirements The combined continuous power output must not exceed 400W. Each output has a maximum and minimum current rating.
® Intel Server System R1000SP Product Family TPS 450W Power Subsystem the PDB harness connectors. The voltage must never exceed the maximum levels when measured at the power pins of the output harness connector during any single point of fail. The voltage must never trip any lower than the minimum levels when measured at the power pins of the PDB connector. Table 30. Over Voltage Protection (OVP) Limits OUTPUT VOLTAGE +3.3V +5V +5VSB +12V1 +12V2 4.7.3 PROTECTION POINT [V] 3.9 V --- 4.5 V 5.6 V --- 6.
® Thermal Management 5. Intel Server System R1000SP Product Family TPS Thermal Management The fully integrated system is designed to operate at external ambient temperatures of between 10ºC- 35ºC. Working with integrated platform management, several features within the system are designed to move air in a front to back direction, through the system and over critical components in order to prevent them from overheating and allow the system to operate with best performance.
® Intel Server System R1000SP Product Family TPS Thermal Management Note: All system fans are controlled independent of each other. The fan control system may adjust fan speeds for different fans based on increasing/decreasing temperatures in different thermal zones within the chassis.
Thermal Management 5.2.3 ® Intel Server System R1000SP Product Family TPS Set Fan Profile This option is used to set the desired Fan Profile. Available settings include: [Performance] and [Acoustic]. Performance mode is designed to provide sufficient cooling capability covering all kinds of addin cards on the market. The Acoustic mode offers the best acoustic experience and appropriate cooling capability supporting the majority of the add-in cards used. 5.2.
® Intel Server System R1000SP Product Family TPS Thermal Management 5. PECI value 6. On-die sensor 7. On-board sensor 8. Virtual sensor 9. Available only when PSU has PMBus* 10. On-board of Module sensor The following diagram illustrates the fan speed control structure: Figure 21. Fan Control Model 5.
Thermal Management ® Intel Server System R1000SP Product Family TPS Figure 22. Fixed System Fan Identification Redundant system fan configuration consists of five managed dual rotor 40mm x 56mm system fans, providing the primary airflow for the system configured with redundant power supply modules. Should a single fan fail, platform management will adjust air flow of the remaining fans and manage other platform features to maintain system thermals.
® Intel Server System R1000SP Product Family TPS Thermal Management The system fan assembly is designed for ease of use and supports several features. System fans are NOT hot-swappable. Each fan and fan assembly is designed for tool-less insertion and extraction from the system. For instructions on fan replacement, see the Intel® Server System R1000SP Service Guide. Fan speed for each fan is controlled by integrated platform management as controlled by the integrated BMC on the server board.
® Thermal Management Intel Server System R1000SP Product Family TPS Table 31.
® Intel Server System R1000SP Product Family TPS Thermal Management the system fully configured and each time the system configuration changes for accurate system monitoring and event reporting. Revision 2.
System Storage and Periferal Options 6. ® Intel Server System R1000SP Product Family TPS System Storage and Peripheral Options The Intel® Server System R1000SP product family has support for many storage device options, including: Fixed 3.5" Hard Disk Drives Hot Swap 3.5" Hard Disk Drives Hot Swap 2.5" Hard Disk Drives SATA Optical Drive SATA DOM Support for different storage and peripheral device options will vary depending on the system SKU.
® Intel Server System R1000SP Product Family TPS System Storage and Periferal Options Light pipes integrated into the drive tray assembly direct light emitted from Amber drive status and Green activity LEDs located next to each drive connector on the backplane, to the drive tray faceplate, making them visible from the front of the system. Amber Status LED Green Activity LED Figure 29.
System Storage and Periferal Options ® Intel Server System R1000SP Product Family TPS Figure 31. Hard Disk Drive Interface Front Connectors On the backside of each backplane are several connectors. The following illustration identifies each. Label A B C D Description 7-pin SATA/SAS I/O connectors SMBus*-In cable connector – From Server board SGPIO connector Power connector Figure 32.
® Intel Server System R1000SP Product Family TPS System Storage and Periferal Options Figure 33. 2.5" Hard Drive Bay Drive Configuration The drive bay can support either SATA or SAS hard disk drives. Mixing of drive types within the hard drive bay is not supported. Hard disk drive type is dependent on the type of host bus controller used, SATA only or SAS. Each 2.5" hard disk drive is mounted to a drive carrier, allowing for hot swap extraction and insertion.
System Storage and Periferal Options ® Intel Server System R1000SP Product Family TPS Figure 36. Installing 2.5" Drive Hot-Swap Backplane Eight hard disk drive interface connectors are mounted on the front side of each backplane (see letter A), each providing both power and I/O signals to the attached hard disk drives. Figure 37. Hard Disk Drive Interface Front Connectors Several connectors are there on the backside of each backplane. The following illustration identifies each.
® Intel Server System R1000SP Product Family TPS System Storage and Periferal Options C – SMBus* Cable Connectors – The backplane includes a 1x5 cable connector used as a management interface to the server board. 6.3.2 Cypress* CY8C22545 Enclosure Management Controller The backplane supports enclosure management using a Cypress* CY8C22545 Programmable System-on-Chip (PSoC*) device.
System Storage and Periferal Options 6.5 ® Intel Server System R1000SP Product Family TPS SATA DOM Support The system has support for a vertical low profile Innodisk* SATA Disk-on-Module (DOM) device. The SATA DOM plugs directly into the 7-pin AHCI SATA port 1 (labeled as “SATA_1”) on the server board, which provides both power and I/O signals. Note: AHCI SATA port 0 (labeled as “SATA_0”) does not include power signal. Figure 41.
® Intel Server System R1000SP Product Family TPS 7. Storage Controller Options Overview Storage Controller Options Overview The server platform supports many different embedded and add-in SATA/SAS controller and SAS Expander options to provide a large number of possible storage configurations. This section will provide an overview of the different options available. 7.
® Storage Controller Options Overview Intel Server System R1000SP Product Family TPS The following table identifies available upgrade key options and their supported features: ® Table 34.
® Intel Server System R1000SP Product Family TPS 7.2.2 Storage Controller Options Overview Maximum drive support = 8 o Note: ESRT2 has no SAS Expander Support Open Source Compliance = Binary Driver (includes Partial Source files) o Meta data is also recognized by MDRAID layer in Linux* (No direct Intel® support, not validated by Intel®) OS Support = Microsoft Windows 7*, Microsoft Windows 2008*, Microsoft Windows 2003*, RHEL*, SLES*, other Linux* variants using partial source builds.
Storage Controller Options Overview ® Intel Server System R1000SP Product Family TPS Features of this option include: Custom on-board system interface connector.
® Intel Server System R1000SP Product Family TPS 8. Front Control Panel and I/O Panel Overview Front Control Panel and I/O Panel Overview All system configurations will include a Control Panel on the front of the system providing push button system controls and LED indicators for several system features. Systems configured with four 3.5” hard drive bays will also include an I/O Panel providing additional system I/O features. This section describes the features and functions of both front panel options.
Front Control Panel and I/O Panel Overview 8.2 ® Intel Server System R1000SP Product Family TPS Control Panel Features The system includes a control panel that provides push button system controls and LED indicators for several system features.
® Intel Server System R1000SP Product Family TPS Front Control Panel and I/O Panel Overview Table 36. System Status LED State Definitions Color Green State Solid on Ok Criticality Description Indicates that the System Status is ‘Healthy‘. The system is not exhibiting any errors. AC power is present and BMC has booted and manageability functionality is up and running. Green ~1 Hz blink Degraded System degraded: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
Front Control Panel and I/O Panel Overview Color Amber State Solid on Criticality Critical, nonrecoverable Description Fatal alarm – system has failed or shutdown: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Off N/A Not ready ® Intel Server System R1000SP Product Family TPS CPU CATERR signal asserted. MSID mismatch detected (CATERR also asserts for this case). CPU 1 is missing. CPU ThermalTrip. No power good – power fault.
® Intel Server System R1000SP Product Family TPS 9. ® Intel Local Control Panel Intel® Local Control Panel The Intel® Local Control Panel option (Intel® Product Order Code – A1U2ULCP) utilizes a combination of control buttons and LCD display to provide system accessibility and monitoring. Label A B C D E F Description LCD Display Left Control Button “Enter” Button Right Control Button USB 2.0 Port USB 2.
® Intel Local Control Panel ® Intel Server System R1000SP Product Family TPS event occurs that results in the system status LED to blink green, then the LCD must display the degraded event that triggered the systems status LED to blink. Banner Figure 46. LCP Background color during normal operation Error Figure 47. LCP Background color during an error If the user presses any button after the system is powered on, then the main menu will be displayed.
® Intel Server System R1000SP Product Family TPS ® Intel Local Control Panel format. By default the first event after the last power on will be displayed. If there are no events after the last power on, then fourth field is empty on the LCD screen. By default, each error event scrolls automatically so that the entire error message can be read without pressing either the left or right scroll buttons.
® ® Intel Local Control Panel Intel Server System R1000SP Product Family TPS b. Server Model: Value specified in the product part number in the product FRU information in the main board BMC FRU. c. Asset tag: Value specified in the product asset tag in the product FRU information in the main board BMC FRU. d. Server GUID: System UUID stored by BIOS. e. Custom String: Custom string placed by the OEM\end user. 9.4.
® Intel Server System R1000SP Product Family TPS 9.5 ® Intel Local Control Panel Config Menu If the user selects Config item in the main menu, then the following options will be displayed to configure. ^ | IP Version | BMC IP | RMM4 IP | Boot Device | Banner Figure 57. LCP – Configure Menu Items The following sub-sections will explain individual items of the configuration menu. 9.5.1 IP Version If the user selects IP Version in the Config menu, the following options will be displayed.
® ® Intel Local Control Panel Intel Server System R1000SP Product Family TPS separated by ‘.’ character in IP address format. The behaviors of these buttons are as follows when the cursor is under this item. 1. Left and Right buttons inside the second menu item traverses among the 0 positions within the same item. 2. If the cursor is under last position inside the second menu item, then a right button will move the cursor to next item, that is, Set. 3.
® Intel Server System R1000SP Product Family TPS 9.5.4 ® Intel Local Control Panel Boot Device If the user selects Boot Device in the Config menu, then the following options will be displayed. The selected item will be set as the next boot option and it will not be a permanent change. ^ | CD\DVD | Hard Drive | Network Boot | EFI Shell Figure 63. Boot options configuration menu 9.5.5 Banner When the user selects Banner in the Config menu, the following options will be displayed.
® PCI Riser Card Support Intel Server System R1000SP Product Family TPS 10. PCI Riser Card Support The system includes one riser card slot on the server board. This section will provide an overview of the available riser card and describe the server board features and architecture supporting them. 10.1 Architectural Overview of the Server Board Riser Slot The server board includes one riser card slot labeled “Slot_6”.
® Intel Server System R1000SP Product Family TPS PCI Riser Card Support 10.2 Riser Card Support The system supports one single slot PCIe x16 mechanical riser cards. The riser card is mounted to a bracket assembly and is installed into the system by aligning the edge connector of the riser card with the matching slot connector on the server board. Figure 66. Add-in Card Support Note: Add-in cards that exceed the PCI Specification for ½ length PCI add-in cards (167.65mm or 6.
® Mezzanine Module Support Intel Server System R1000SP Product Family TPS 11. Mezzanine Module Support 11.1 I/O Module Support In addition to the embedded I/O features of the server board, and those available with the addition of a PCIe add-in card, the server also provides concurrent support of an optionally installed mezzanine I/O module. Figure 67. Installing I/O Module ® The following table lists the Intel I/O modules available for this server: ® Table 38.
® Intel Server System R1000SP Product Family TPS Mezzanine Module Support ® Table 39. Supported Intel Remote Management Module Intel® Product Code AXXRMM4LITE AXXRMM4R Description Kit Contents Intel Remote Management Module 4 Lite ® Intel Remote Management Module 4 RMM4 Lite Activation Key RMM4 Lite Activation Key Dedicated NIC Port Module ® Benefits Enables KVM and media redirection through onboard NIC Dedicated NIC for management traffic.
® Mezzanine Module Support Intel Server System R1000SP Product Family TPS Table 40. Enabling Advanced Management Features Manageability Hardware Benefits ® Comprehensive IPMI based base manageability features ® No dedicated NIC for management Enables KVM and media redirection through onboard NIC ® Dedicated NIC for management traffic. Higher bandwidth connectivity for KVM and media Redirection with 1Gbe NIC.
® Intel Server System R1000SP Product Family TPS Appendix A: Integration and Usage Tips Appendix A: Integration and Usage Tips This section provides a list of useful information that is unique to the Intel® Server System R1000SP Product Family and should be kept in mind while configuring your server system.
® Intel Server System R1000SP Product Family TPS Appendix B: POST Code Diagnostic LED Decoder Appendix B: POST Code Diagnostic LED Decoder As an aid to assist in trouble shooting a system hang that occurs during a system’s Power-On Self Test (POST) process, the server board includes a bank of eight POST Code Diagnostic LEDs on the back edge of the server board.
® Intel Server System R1000SP Product Family TPS Appendix B: POST Code Diagnostic LED Decoder In the following example, the BIOS sends a value of ACh to the diagnostic LED decoder. The LEDs are decoded as follows: Table 41.
® Intel Server System R1000SP Product Family TPS Appendix B: POST Code Diagnostic LED Decoder Diagnostic LED Decoder 1 = LED On, 0 = LED Off Checkpoint Upper Nibble Lower Nibble MSB LSB 8h 4h 2h 1h 8h 4h 2h 1h LED # #7 #6 #5 #4 #3 #2 #1 #0 62h 0 1 1 0 0 0 1 0 63h 0 1 1 0 0 0 1 1 68h 0 1 1 0 1 0 0 0 69h 0 1 1 0 1 0 0 1 6Ah 0 1 1 0 1 0 1 0 70h 0 1 1 1 0 0 0 0 71h 0 1 1 1 0 0 0 1 72h 0 1 1 1 0 0 1 0 78h 0 1 1 1 1 0 0 0 79h 0 1 1 1 1 0 0 1 90h 1 0 0 1 0 0 0 0 91h 1 0 0 1 0 0 0 1 92h 1 0 0 1 0 0 1 0 93h 1 0 0 1
® Intel Server System R1000SP Product Family TPS Appendix B: POST Code Diagnostic LED Decoder Diagnostic LED Decoder 1 = LED On, 0 = LED Off Checkpoint Upper Nibble Lower Nibble MSB LSB 8h 4h 2h 1h 8h 4h 2h 1h LED # #7 #6 #5 #4 #3 #2 #1 #0 F1h 1 1 1 1 0 0 0 1 F2h 1 1 1 1 0 0 1 0 F3h 1 1 1 1 0 0 1 1 F4h 1 1 1 1 0 1 0 0 Description PEIM which detected User Recovery condition Recovery PEIM (Recovery started) Recovery PEIM (Capsule found) Recovery PEIM (Capsule loaded) POST Memory Initialization MRC Diagnos
® Intel Server System R1000SP Product Family TPS Appendix B: POST Code Diagnostic LED Decoder Table 44.
® Intel Server System R1000SP Product Family TPS Appendix C: POST Code Errors Appendix C: POST Code Errors Most error conditions encountered during POST are reported using POST Error Codes. These codes represent specific failures, warnings, or are informational. POST Error Codes may be displayed in the Error Manager display screen, and are always logged to the System Event Log (SEL). Logged events are available to System Management applications, including Remote and Out of Band (OOB) management.
Appendix C: POST Code Errors Error Code 5224 8130 8131 8132 8133 8160 8161 8162 8163 8170 8171 8172 8173 8180 8181 8182 8183 8190 8198 8300 8305 83A0 83A1 84F2 84F3 84F4 84FF 8500 8501 8520 8521 8522 8523 8524 8525 8526 8527 8528 8529 852A 852B 852C 852D 852E 852F 8530 8531 8532 8533 8534 8535 8536 8537 8538 8539 853A 853B 853C 853D 853E 70 ® Intel Server System R1000SP Product Family TPS Error Message Password clear jumper is Set Processor 01 disabled Processor 02 disabled Processor 03 disabled Process
® Intel Server System R1000SP Product Family TPS Error Code 853F (Go to 85C0) 8540 8541 8542 8543 8544 8545 8546 8547 8548 8549 854A 854B 854C 854D 854E 854F 8550 8551 8552 8553 8554 8555 8556 8557 8558 8559 855A 855B 855C 855D 855E 855F (Go to 85D0) 8560 8561 8562 8563 8564 8565 8566 8567 8568 8569 856A 856B 856C 856D 856E 856F 8570 8571 8572 8573 8574 8575 8576 8577 Appendix C: POST Code Errors DIMM_K2 failed test/initialization Error Message Response Major DIMM_A1 disabled DIMM_A2 disabled DIMM_A3
Appendix C: POST Code Errors Error Code 8578 8579 857A 857B 857C 857D 857E 857F (Go to 85E0) 85C0 85C1 85C2 85C3 85C4 85C5 85C6 85C7 85C8 85C9 85CA 85CB 85CC 85CD 85CE 85CF 85D0 85D1 85D2 85D3 85D4 85D5 85D6 85D7 85D8 85D9 85DA 85DB 85DC 85DD 85DE 85DF 85E0 85E1 85E2 85E3 85E4 85E5 85E6 85E7 85E8 85E9 85EA 85EB 85EC 85ED 85EE 85EF 8604 8605 8606 72 ® Intel Server System R1000SP Product Family TPS Error Message DIMM_I1 encountered a Serial Presence Detection (SPD) failure DIMM_I2 encountered a Serial Pre
® Intel Server System R1000SP Product Family TPS Error Code 92A3 92A9 A000 A001 A002 A003 A100 A421 A5A0 A5A1 A6A0 Appendix C: POST Code Errors Error Message Serial port component was not detected Serial port component encountered a resource conflict error TPM device not detected. TPM device missing or not responding. TPM device failure. TPM device failed self test.
® Appendix C: POST Code Errors 74 Intel Server System R1000SP Product Family TPS Code 1-5-1-2 Reason for Beep VR Watchdog Timer sensor assertion Associated Sensors VR controller DC power on sequence was not completed in time. 1-5-1-4 Power Supply Status The system does not power on or unexpectedly powers off and a Power Supply Unit (PSU) is present that is an incompatible model with one or more other PSUs in the system. Intel Order Number G64249-002 Revision 2.
® Intel Server System R1000SP Product Family TPS Glossary Glossary Word/Acronym Definition ACA Australian Communication Authority ANSI American National Standards Institute BMC Baseboard Management Controller BIOS Basic Input/Output System CMOS Complementary Metal-oxide-semiconductor D2D DC-to-DC EMP Emergency Management Port FP Front Panel FRB Fault Resilient Boot FRU Field Replaceable Unit 2 IC Inter-integrated Circuit bus LCD Liquid Crystal Display LPC Low-pin Count LSB L
Reference Documents ® Intel Server System R1000SP Product Family TPS Reference Documents See the following documents for additional information: 76 Intel® Server Board S1400SP Technical Product Specification Intel® Server Board S1400SP Product Family Spares/Parts List and Configuration Guide Intel® Server System R1000SP Service Guide Intel® Server System R1000SP Quick Installation Guide BIOS for PCSD Platforms Based on Intel® Xeon Processor E5-4600/2600/2400/1600 Product Families Ext
