Quick Start Guide Back

ManualsBrandsIntel ManualsOtherIntel Server Board S1200BTSR

Software

• BIOS, Drivers, and Operating System Installation

A. Conﬁrm BIOS Version: Look on the Server/System Management screen in the BIOS

Setup Utility to determine the installed BIOS version. Compare this to the versions at:

http://www.intel.com/support/motherboards/server.

If new versions are available, update the BIOS on your server. See the Techinical Product Speciﬁcation

on the Intel

Server Deployment Toolkit CD for update instructions.

B. Conﬁgure your RAID Controller:

Use the instructions provided with the RAID controller.

C. Install your Operating System:

Use the instructions provided with the RAID controller

and with the operating system.

D. Install Operating System Drivers: With the operating system running, insert the

Intel

Server Deployment Toolkit CD. If using a Microsoft Windows* operating system, the Intel

Deployment Assistant will autorun and allow you to select the appropriate drivers to install. On other

operating systems, browse the CD folders to locate and install the driver ﬁles.

Side 2

Install Optical

Drive and

Hard Drive(s)

See the documentation that came

with your server chassis for drive

installation.

Install Add-in

Card[s]

See the documentation that came with your

server chassis for add-in card installation.

For the Intel

Server Chassis P4000 series,

see the Quick Start User's Guide

accompanying the chassis.

Finishing Up

Before installing your operating system, you must ﬁnish your chassis

installation, make I/O connections and plug in AC power.

See your chassis documentation for AC power and grounding requirements.

CAUTION: See your chassis

documentation for AC power and

grounding requirements.

Network

USB

0-1

USB

2-3

NIC1

10/100/

1000 Mb

NIC2

10/100/

1000 Mb

Video

Serial A

Common Problems and Solutions

The system does not boot or show video at power-on.

•

Check that the +12V CPU power connector is plugged in. Without this cable, the processors will not have any power.

•

Only Intel

Xeon

E3-1200 processors, the 2

Generation Intel

Core™ i3 processors, Intel

Xeon

E3-1200 V2 processors or the 3

Generation Intel

Core™ i3 processors

with 95W and

less Thermal Design Power (TDP) are supported on this server board. Previous generation Intel

Xeon

processors are not supported.

Beep code 1-5-2-1 in a system means you do not have the supported processor installed.

•

The system generates the memory error beep code and POST diagnostic LED message {0XE0~0XEF} that indicates memory errors in early POST.

•

Remember, all DIMMs must be:

–

DDR3 1066/1333/1600 MHz UDIMM.

–

From the same manufacturer.

–

Installed beginning with DIMM A1.

For a list of hardware components that have been tested with this system, see:

http://www.intel.com/support/motherboards/server.

Attach Intrusion Switch Cable

Note: For a non-Intel chassis, see your chassis

documentation for intrusion switch requirements.

Server

Board

Server

Board

Intrusion

Switch

Connector

IMPORTANT NOTE:

Return to your Intel

Server

Chassis Quick Start User's

Guide, or your non-Intel

chassis documentation to

ﬁnish installation and

conﬁguration of your Intel

Server Board S1200BTS.

Return to this document to

ﬁnish up, including software,

BIOS, drivers and operating

system installation.

Attach Front Panel, Serial, and USB Connections

Note: For a non-Intel

chassis,

see your chassis documentation

for front panel features and server

board connection requirements.

Internal

USB/Serial

Connector

Detail

Serial B

USB

Front Panel

USB Floppy

USB

Connector

Detail

Chassis Fan Connections

For a non-Intel

server chassis, see the "Making Connections ... Quick Reference"

section below, and the documentation accompanying your chassis for speciﬁc

chassis fan connection requirements.

Attach fans

with 4-pin

connectors

here.

Server

Board

Install DIMM Memory Modules

To Install DIMMs:

DDR3 DIMM Memory Identiﬁcation:

Open both DIMM socket levers.

Push down ﬁrmly on the DIMM until it

snaps into place and both levers close.

Insert DIMM making sure the connector edge

of the DIMM aligns correctly with the slot.

IMPORTANT! Visually check that each

latch is fully closed and correctly

engaged with each DIMM edge slot.

Note location of alignment notch.

CAUTION: Avoid touching contacts when

handling or installing DIMMs.

DIMM

notch and

socket

bump must

align as

shown.

Other

Memory

DDR3

This server board supports up to 4 DDR3 1066/1333/1600

ECC UDIMM.

CAUTION: Observe normal ESD (ElectroStatic Discharge) procedures

to avoid possible damage to system components.

Memory Conﬁgurations and Population Order:

Memory Type: Minimum of one 1 GB, DDR3 1066/1333/1600 MHz ECC UDIMM.

Note: For additional memory conﬁgurations, see the Intel

Server Board S1200BTS

Techinical Product Speciﬁcation at:

http://www.intel.com/support/motherboards/server.

Memory sizing and conﬁguration is supported only for qualiﬁed DIMMs approved by

Intel

. For a list of supported memory, see the tested memory list at

http://serverconﬁgurator.intel.com/default.aspx

DIMM A2

DIMM A1

DIMM B2

DIMM B1

Intel

Server Board S1200BTS

Component Layout

Note: Not all

components, jumpers

and connectors are

described in this

diagram. Refer to

your Server Board

Technical Product

Speciﬁcation on the

Intel

Server

Deployment Toolkit

CD for additional

information.

SATA 5

SATA 2

SATA 1

SATA 0

USB 4-5

Front Panel

Connector

SATA 4

SATA 3

SATA_SGPIO

SYS FAN_3

SYS FAN_1

Processor Socket

CPU Fan

Connector

CMOS battery

HDD LED

TPM

SATA Key

Chassis Intrusion

CPU Power

Connector

Diagnostic

LEDs

SYS FAN_2

Note: Refer to the Technical Product Specification

for Diagnostic LED decoder list.

Slot 4 ( PCI )

Default

Recover

J2G1

BIOS

Recovery

Default

Clear

J1H3

CMOS

Clear

Default

J1G1

Password

Clear

Cleared

Default

J2J1

Enabled

Force

Update

Serial-A

VGA

NIC2

USB2

USB3

NIC1

USB0

USB1

Main Power

Connector

DIMM_A2

DIMM_A1

DIMM_B2

DIMM_B1

Slot 6 ( PCIe x 8 ) LP Riser

Slot 5 ( PCIe x 4 )

Slot 7 ( PCIe x 8 )

USB 6

Reset Button

NIC 2

Link/Act

NIC 1

Link/Act

Power Button

HDD LED

Power LED

Front Panel Header

(J1C1)

Document/Tool

Available Documents

Technical Product Speciﬁcation

Monthly Speciﬁcation Update

Spares, Parts List, and Conﬁguration Guide

Sever Conﬁgurator Tool

Software and Drivers

Content

In-depth technical information

Technical information and issues update

Supported accessories and spares list

Tested peripherals and operating systems list

Tested memory list

Supported processors list

Up-to-date ﬁrmware, driver and utility information

Additional Reference documents available at:

http://www.intel.com/support/motherboards/server.

A complete list of accessories and spares can be found at:

http://www.intel.com/support/motherboards/server

(search for the document titled “Spares and Conﬁguration Guide”.)

Accessories and Order Codes

Intel

Integrated RAID Module

Intel

Integrated RAID Module

Intel

Trusted Platform Module

AXXTPME3

AXXRMS2AF040

AXXRMS2LL040

Additional Reference documents available at:

http://www.intel.com/support/motherboards/server

ATX I/O Shield AXXTIO

SATA Slim-Line DVD

AXXSATADVDROM

Making Connections to the Server Board ... Quick Reference

Make this connection

D. System Fan 1 Header

E. System Fan 2 Header

F. System Fan 3 Header

Intel

Server Chassis

P4000 series

CPU/System Fan Connections

A. +12V CPU Power Connector

B. Main Power Connector

C. Front Panel Header

Required Connections

Intel

Server Chassis

P4000 series

Make this connection

Optional Connections

H. USB 4-6

I. SATA Connectors

J. SATA SGPIO

K. TPM

L. SATA Key

M. Chassis Intrusion Header

Intel

Server Chassis

P4000 series

G. CPU Fan Header

IMPORTANT Note:

Cables should be

tied for better airﬂow.

Use cable-ties as necessary.

Front Panel

Serial ATA

USB

4-5

Main Power

12V CPU Power

Intrusion

SATA Key

SATA SGPIO

TPM

CPU Fan

Sys Fan 3

Sys Fan 1

Sys Fan 2

Note: For a non-Intel Chassis, see your chassis

documentation for server board connection information.

Note: Not all optional connections are shown in this

diagram. Refer to your Server Board Service Guide, and

your server chassis documentation for additional

connection information.

Make Server

Board Power

Connections

Attach the CPU power connector.

Attach the main power connector.

IMPORTANT NOTE:

If you are using a non-Intel server chassis

with an ATX power supply, see the documentation that came

with your chassis for installation information.

CAUTION:

Note the location of the

latch on each power cable

connector and align it with the matching

tab on each server board socket.

Main Power

Connector Detail

Latch

Tab

CPU Power

Connector Detail

Connect Hard Drives/Optical

Drive to Server Board

Connect SATA Data Cables

to server board here.

Begin cable connections

at the SATA 0 location.

SATA Data

Cable Connector

Server

Board

Server

Board