Quick Start Guide Back

ManualsBrandsIntel ManualsOtherIntel Server Board S1200BTSR

Software

• BIOS, Drivers, and Operating System Installation

A. Conﬁrm BIOS Version: Look on the Server/System Management screen in the BIOS

Setup Utility to determine the installed BIOS version. Compare this to the versions at:

http://www.intel.com/support/motherboards/server.

If new versions are available, update the BIOS on your server. See the Technical Product Specification

on the Intel

Server Deployment Toolkit CD for update instructions.

B. Conﬁgure your RAID Controller:

Use the instructions provided with the RAID controller.

C. Install your Operating System:

Use the instructions provided with the RAID controller

and with the operating system.

D. Install Operating System Drivers: With the operating system running, insert the

Intel

Server Deployment Toolkit CD. If using a Microsoft Windows* operating system, the Intel

Deployment Assistant will autorun and allow you to select the appropriate drivers to install. On other

operating systems, browse the CD folders to locate and install the driver files.

Side 2

Install Optical

Drive and

Hard Drive(s)

See the documentation that came

with your server chassis for drive

installation.

Install Add-in

Card[s]

See the documentation that came with your

server chassis for add-in card installation.

For the Intel

Server Chassis P4000 series,

see the Quick Start User's Guide

accompanying the chassis.

Finishing Up

Before installing your operating system, you must finish your chassis

installation, make I/O connections and plug in AC power.

See your chassis documentation for AC power and grounding requirements.

CAUTION: See your chassis

documentation for AC power and

grounding requirements.

Network

USB

0-1

USB

2-3

NIC1

10/100/

1000 Mb

NIC2

10/100/

1000 Mb

Video

Serial A

Common Problems and Solutions

The system does not boot or show video at power-on stage.

•

Check that the +12V CPU power connector is plugged in. The processors will not have any power without this cable.

•

Only Intel

Xeon

E3-1200 processors, the 2

Generation Intel

Core™ i3 processors, Intel

Xeon

E3-1200 V2 processors or the 3

Generation Intel

Core™ i3 processors

with 95W and less Thermal Design Power (TDP) are supported on this server board. Previous generation Intel

Xeon

processors are not supported.

Beep code 1-5-2-1 in a system means you do not have the supported processor installed.

•

The system generates the memory error beep code and POST diagnostic LED message {0XE0~0XEF} that indicates memory errors in early POST.

•

Remember, all DIMMs must be:

–

DDR3 1066/1333/1600 MHz UDIMM.

–

From the same manufacturer.

–

Installed beginning with DIMM A1.

For a list of hardware components that have been tested with this system, see:

http://www.intel.com/support/motherboards/server.

Connect Hard Drives/Optical

Drive to Server Board

Connect SATA Data Cables

to server board here.

Begin cable connections

at the SATA 0 location.

NOTE: SATA 0 and SATA 1

are 6Gb/s SATA port

Server

Board

SATA Data

Cable Connector

Server

Board

Attach Intrusion Switch Cable

NOTE: For a non-Intel

chassis, see your chassis

documentation for intrusion switch requirements.

Server

Board

Intrusion

Switch

Connector

IMPORTANT NOTE:

Return to your Intel

Server

Chassis Quick Start User's

Guide, or your non-Intel

chassis documentation to

finish installation and

configuration of your Intel

Server Board S1200BTL

and S1200BTLRM.

Return to this document to

finish up, including software,

BIOS, drivers and operating

system installation.

Attach Front Panel, Serial, and USB Connections

NOTE: For a non-Intel

chassis,

see your chassis documentation

for front panel features and server

board connection requirements.

Internal

USB/Serial

Connector

Detail

Serial B

USB 10-11

USB 4-5

Front Panel

USB Floppy

USB

Connector

Detail

Chassis Fan Connections

For a non-Intel

server chassis, see the "Making Connections...Quick Reference"

section below, and the documentation accompanying your chassis for specific

chassis fan connection requirements.

Attach fans

with 4-pin

connectors

here.

Server

Board

Install DIMM Memory Modules

To Install DIMMs:

DDR3 DIMM Memory Identiﬁcation:

Open both DIMM socket levers.

Push down firmly on the DIMM until it

snaps into place and both levers close.

Insert DIMM making sure the connector edge

of the DIMM aligns correctly with the slot.

IMPORTANT! Visually check that each

latch is fully closed and correctly

engaged with each DIMM edge slot.

Note location of alignment notch.

CAUTION: Avoid touching contacts when

handling or installing DIMMs.

DIMM

notch and

socket

bump must

align as

shown.

Other

Memory

DDR3

This server board supports up to 4 DDR3 1066/1333/1600

ECC UDIMM.

CAUTION: Observe normal ESD (ElectroStatic Discharge) procedures

to avoid possible damage to system components.

Memory Conﬁgurations and Population Order:

Memory Type: Minimum of one 1 GB, DDR3 1066/1333/1600 MHz ECC UDIMM.

Note: For additional memory configurations, see the Technical Product Specification

on the Intel

Server Deployment Toolkit CD that accompanied your Intel

Server

Board S1200BTL and S1200BTLRM, or go to:

http://www.intel.com/support/motherboards/server.

Memory sizing and configuration is supported only for qualified DIMMs approved by

Intel

. For a list of supported memory, see the tested memory list at

http://serverconfigurator.intel.com/default.aspx.

DIMM A2

DIMM A1

DIMM B2

DIMM B1

Intel

Server Board S1200BTL and S1200BTLRM Component Layout

Note: Not all components,

jumpers and connectors are

described in this diagram.

Refer to your Server Board

Technical Product Specification

on the Intel

Server

Deployment Toolkit CD for

additional information.

DIMM_A2

DIMM_A1

DIMM_B2

DIMM_B1

Serial B

Internal

USB

SATA 5

SATA 2

SATA 1

SATA 0

Internal USB

Floppy Connector

Internal

USB

Front Panel

Connector

SATA 4

SATA 3

IPMB

SAS Module

Connector

Internal

USB SSD

SATA_SGPIO

SYS FAN_3SYS FAN_1 SYS FAN_2

Processor Socket

CPU Fan

Connector

RMM NIC

CMOS battery

Main Power

Connector

P/S

AUX

CPU Power

Connector

NIC2

USB2

USB3

NIC1

USB0

USB1

Serial

Port A

Video

Diagnostic/

Status LEDs

ID LED

SYS FAN_4

Note: Refer to the Technical Product Specification

for Diagnostic LED decoder list.

HSBP

J1F3

BIOS

Recovery

J1E2

CMOS

Clear

J4A2

BMC

Force

Update

J1F1

Password

Clear

J1F2

Force

Update

Slot 1 ( PCI )

Slot 3 ( PCIe

x 4 )

Slot 4 ( PCIe

x 4 )

Slot 5 ( PCIe

x 4 )

Slot 6 ( PCIe

x 8 ) LP Riser

Chassis Intrusion

RMM4 Lite

SATA Key

TPM

HDD LED

Document/Tool

Available Documents

Technical Product Specification

Monthly Specification Update

Spares, Parts List, and Configuration Guide

Sever Configurator Tool

Software and Drivers

Content

In-depth technical information

Technical information and issues update

Supported accessories and spares list

Tested peripherals and operating systems list

Tested memory list

Supported processors list

Up-to-date firmware, driver and utility information

Additional Reference documents available at:

http://www.intel.com/support/motherboards/server

A complete list of accessories and spares can be found at:

http://www.intel.com/support/motherboards/server.

(Search for the document Spares and Configuration Guide.)

Making Connections to the Server Board ... Quick Reference

Make this connection

D. System Fan 1 Header

E. System Fan 2 Header

F. System Fan 3 Header

G. System Fan 4 Header

Intel

Server Chassis

P4000 series

CPU/System Fan Connections

A. +12V CPU Power Connector

B. Main Power Connector

C. Front Panel Header

Required Connections

Intel

Server Chassis

P4000 series

Make this connection

Optional Connections

I. HSBP

J. USB 4-5 10-11

K. SATA Connectors

L. Serial B

M. Chassis Intrusion Header

N. IPMB

O. SATA SGPIO

P. Internal USB SSD

Q. SAS Module Header

R. USB Floppy

S. P/S Auxiliary

T. SATA Key

U. RMM4 Lite

V. RMM4 NIC

W. TPM

X. HDD LED

Intel

Server Chassis

P4000 series

H. CPU Fan Header

IMPORTANT Note:

Cables should be

tied for better airflow.

Use cable-ties compulsarily.

Front Panel

DIMM A2

DIMM A1

DIMM B2

DIMM B1

Serial ATA

USB

4-5

10-11

USB Floppy

Main Power

12V CPU Power

Intrusion

RMM4 Lite

SATA Key

IPMB

SATA SGPIO

HDD LED

RMM4 NIC

HSBP

Serial B

TPM

Int. USB SSD

SAS Module

CPU Fan 1

Sys Fan 3

Sys Fan 1

Sys Fan 2

Sys Fan 4

P/S AUX Power

NOTE: For a non-Intel

Chassis, see your chassis documentation for server board

connection information.

NOTE: Not all optional connections are shown in this diagram. Refer to your Server Board

Service Guide, and your server chassis documentation for additional connection information.

Make Server

Board Power

Connections

Attach the CPU power connector.

Attach the main power connector.

IMPORTANT NOTE:

If you are using a non-Intel

server chassis

with an ATX power supply, see the documentation that came

with your chassis for installation information.

CAUTION:

Note the location of the

latch on each power cable

connector and align it with the matching

tab on each server board socket.

Attach the P/S Auxiliary power connector.

Main Power

Connector Detail

Latch

Tab

CPU Power

Connector Detail

P/S auxiliary

Power

Connector Detail

Latch

Tab

Accessories and Order Codes

Intel

Remote Management Module 4

Intel

SAS Entry RAID Module

Intel

Integrated RAID Module

Intel

Integrated RAID Module

AXXRMM4

Intel

Remote Management Module 4 Lite

Intel

Trusted Platform Module

AXXRMM4Lite

AXXTPME3

AXX4SASMOD

AXXRMS2AF040

AXXRMS2LL040

Additional Reference documents available at:

http://www.intel.com/support/motherboards/server.

ATX I/O Shield AXXTIO

SATA Slim-Line DVD

AXXSATADVD

Intel® Integrated RAID Module RMT3PB080

Intel® Integrated RAID Module RMS25PB080

Intel® Integrated RAID Module RMS25PB040

Intel® Integrated RAID Module RMS25KB080

Intel® Integrated RAID Module RMS25KB040