Quick Start Guide Back

Side 2
Front Panel Controls and Indicators
(shown with bezel removed)
A. USB 2.0 Connectors
B. System ID Button
C. NMI Button
D. LAN1 LED
E. LAN3 LED
F. Reset Button
G. Status/Fault LED
H. Power Button
I. HDD LED
J. LAN4 LED
K. LAN2 LED
A B C D E F G H
I
JK
15
Install Rack
Handles
13
Install Processor Air Duct
Install processor air duct as shown.
NOTE: Use care to avoid
pinching system cables.
Intel
®
Server
Board
S1200BTS
Component
Layout
SATA 5
SATA 2
SATA 1
SATA 0
USB 4-5
Front Panel
Connector
SATA 4
SATA 3
SATA_SGPIO
SYS FAN_3
SYS FAN_1
Processor Socket
CPU Fan
Connector
CMOS battery
HDD LED
TPM
SATA Key
Chassis Intrusion
CPU Power
Connector
Diagnostic LEDs
SYS FAN_2
Slot 4 ( PCI )
3
2
Default
Recover
J2G1
BIOS
Recovery
3
2
Default
Clear
J1H3
CMOS
Clear
3
2
Default
J1G1
Password
Clear
Cleared
3
2
Default
J2J1
Enabled
ME
Force
Update
Serial-A
VGA
NIC2
USB2
USB3
NIC1
USB0
USB1
Main Power
Connector
DIMM_A2 DIMM_A1 DIMM_B2 DIMM_B1
Slot 6 ( PCIe x 8 ) LP Riser Slot 5 ( PCIe x 4 ) Slot 7 ( PCIe x 8 )
USB 6
2
Reset Button
NIC 2
Link/Act
NIC 1
Link/Act
Power Button
HDD LED
Power LED
Front Panel Header
(J1C1)
Note: Refer to the Technical Product Specification
for Diagnostic LED decoder list.
17
Software
• BIOS, Drivers, and Operating System Installation
A. Confirm BIOS Version: Look on the Server/System Management screen in the BIOS
Setup Utility to determine the installed BIOS version. Compare this to the versions at:
http://www.intel.com/support/motherboards/server
If new versions are available, update the BIOS on your server. See the Techinical Product Specification
on the Intel
®
Server Deployment Toolkit CD for update instructions.
B. Configure your RAID Controller: Use the instructions provided with the RAID controller.
C. Install your Operating System: Use the instructions provided with the RAID controller
and with the operating system.
D. Install Operating System Drivers: With the operating system running, insert the
Intel
®
Server Deployment Toolkit CD. If using a Microsoft Windows* operating system, the Intel
®
Deployment Assistant will autorun and allow you to select the appropriate drivers to install. On other
operating systems, browse the CD folders to locate and install the driver files.
12
Install PCIe Add-in
Card RiserAssembly
A
Align the riser assembly
with the server board
riser socket.
B
Press the riser
assembly into
place and secure
with the screw.
PCI Riser
Socket
B
A
Riser Card
Connector
11
Install PCIe Add-in Card
A
B
C
CAUTION:
Observe normal ESD precautions
when installing add-in cards.
Remove filler panel from the add-in
card slot.
Insert add-in card until it seats in the
riser connector.
Secure add-in card with screw as
shown.
Riser Connector
REMOVE Filler Panel
A
B
Add-in Card
C
8
Install Hard Drives/Carriers
B
Remove the screws securing the drive carrier to
the chassis.
Slide the carrier away from the chassis.
A
Attach the hard drive to the carrier with
four screws as shown.
Re-install the hard drive/carrier assembly into the chassis.
C
Insert hard drive into the carrier with
the bottom-side of the drive facing up.
D
E
Secure the hard drive/carrier assembly with the screws.
F
C
D
Note: Hard
drive 0 location
is shown
above.
B
Screw
A
F
Screw
E
9
Cabling Hard Drives
A
B
C
Connect SATA data
cable(s) to server
board as shown.
Connect opposite end
of SATA data cable(s)
to hard drive(s) as
shown ... see detail .
Connect the SATA fixed
drive power connectors
to each hard drive as
shown ... see detail.
Optical
Device
Fixed
Drive 0
Fixed
Drive 1
Fixed
Drive 2
Fixed
Drive 3
Power
Supply
SATA 1
Server
Board
SATA 0
SATA 2
SATA 3
BLUE indicates Data Cable
RED indicates Power Cable
Cable
Legend
A
Data
Power
Back View of
SATA Drive
B
C
10
Install and Cable Optical Device (optional)
F
C
Remove the security screws.
Remove the Filler Panel.
D
A
B
CAUTION:
To maintain proper system cooling,
a filler blank must be
installed if you do
not install a device
at this location.
Pull the power and data cables through
the front of the chassis opening.
E
Connect the cables as shown.
Rear View
of Optical
Drive
C
Insert optical device assembly into front
panel opening and push all the way until
it stops .
Install the plastic latch on the rear side of
the drive and fix it with two screws.
D
Data
Power
Optical
Drive
E
IMPORTANT NOTE: Refer
to the Cabling Diagram
below for connection
locations and cable
routing.
B
A
Optical
Device Tray
Assembly
F
16
Finishing Up
Before installing your operating system, you must finish your system
installation and connect back panel I/O connectors and AC power.
CAUTION: This unit must
be operated with the TOP
COVER installed to ensure
proper cooling.
2. Connect your keyboard, mouse, video
and other I/O cables/devices as shown.
Then connect the AC power cord.
1. Make sure you have replaced the system cover.
Network
NIC1
Network
NIC2
USB
0, 1
USB
2, 3
Serial
Port A
Video
AC Power
PCI-E Card
Platform Cabling Diagram
Front Panel USB
Front Panel
HDD 0 to Server Board SATA 0
HDD 1 to Server Board SATA 1
HDD 2 to Server Board SATA 2
HDD 3 to Server Board SATA 3
System Fan #1 Power
System Fan #2 Power
System Fan #3 Power
Power to Server Board (Main)
Power to Server Board (CPU)
Optical Device SATA Data Cable
Optical Device to Power Supply
HDD to Power Supply
A
B
C
D
E
F
G
H
I
J
K
L
M
N
Server Board SATA
Connector Legend
0
2
4
1
3
5
HDD 0 HDD 1 HDD 2 HDD 3
Optical Device
A
N
G H I
J
K
C
L M
D E F
B
CPU
Server
Board
Power
Supply
Available Documents
Technical Product Specification
Quick Reference Label
Quick Start User Guide/System Configuration
Guide
Additional Reference documents available at:
http://www.intel.com/support/motherboards/
server
A complete list of accessories and spares can be found at:
http://www.intel.com/support/motherboards/server
Optional Accessories/Spares and Order Codes
Value Rail kit
AXXVRAIL
SATA Slim-line DVD
AXXSATADVDROM
Intel
®
Trusted Platform Module AXXTPME3
14
Install the Top Cover
B
Tighten the four screws.
A
Place cover onto chassis and slide forward to engage recessed
edge at front of cover. Make sure the latch is locked.
A
A
B
Recessed
Edge