Quick Start Guide Back

ManualsBrandsIntel ManualsOtherIntel Server Board S1200BTSR

Side 2

Front Panel Controls and Indicators

(shown with bezel removed)

A. USB 2.0 Connectors

B. System ID Button

C. NMI Button

D. LAN1 LED

E. LAN3 LED

F. Reset Button

G. Status/Fault LED

H. Power Button

I. HDD LED

J. LAN4 LED

K. LAN2 LED

A B C D E F G H

Install the Top Cover

Tighten the four screws.

Place cover onto chassis and slide forward

to engage recessed edge at front of cover.

Make sure the latch is locked.

Recessed

Edge

Install Rack

Handles

Install Processor Air Duct

Install processor air

duct as shown.

NOTE: Use care to

avoid pinching

system cables.

Intel

Server Board S1200BTL Component Layout

Default

Recover

J1F3

BIOS

Recovery

Default

Clear

J1E2

CMOS

Clear

Default

Enabled

J4A2

BMC

Force

Update

Default

J1F1

Password

Clear

Password

Clear

Default

J1F2

Enabled

Force

Update

DIMM_A2

DIMM_A1

DIMM_B2

DIMM_B1

Serial B

Internal

USB

SATA 5

SATA 2

SATA 1

SATA 0

Internal USB

Floppy Connector

Internal

USB

Front Panel

Connector

SATA 4

SATA 3

IPMB

SAS Module

Connector

Internal

USB SSD

SATA_SGPIO

SYS FAN_3SYS FAN_ 1 SYS FAN_2

Processor Socket

CPU Fan

Connector

RMM4 NIC

CMOS battery

HDD LED

TPM

RMM4 Lite

SATA Key

Chassis Intrusion

Main Power

Connector

P/S

AUX

CPU Power

Connector

ID LED

NIC2

USB2

USB3

NIC1

USB0

USB1

Serial

Port A

Video

Diagnostic LED

SYS FAN_4

Note: Refer to the Technical Product Specification

for Diagnostic LED decoder list.

HSBP

Slot 1 ( PCI )

Slot 3 ( PCIe

x 4 )

Slot 4 ( PCIe

x 4 )

Slot 5 ( PCIe

x 4 )

Slot 6 ( PCIe

x 8 ) LP Riser

Reset Button

NIC 2

Link/Act

NIC 1

Link/Act

Power Button

HDD LED

Power LED

Front Panel

Header (J1C1)

Status LED

Software

• BIOS, Drivers, and Operating System Installation

D. Install Operating System Drivers: With the operating system running,

insert the Intel

Server Deployment Toolkit CD. If using a Microsoft Windows* operating

system, the Intel

Deployment Assistant will autorun and allow you to select the

appropriate drivers to install. On other operating systems, browse the CD folders to locate

and install the driver ﬁles.

C. Install your Operating System:

Use the instructions provided with the RAID

controller

and with the operating system.

B. Conﬁgure your RAID Controller:

Use the instructions provided with the RAID

controller.

A. Conﬁrm BIOS Version: Look on the Server/System Management screen in the

BIOS Setup Utility to determine the installed BIOS version. Compare this to the versions at:

http://www.intel.com/support/motherboards/server

If new versions are available, update the BIOS on your server. See the Techinical Product

Speciﬁcation on the Intel

Server Deployment Toolkit CD for update instructions.

Install PCIe Add-in

Card RiserAssembly

Align the riser assembly

with the server board

riser socket.

Press the riser

assembly into

place and secure

with the screw.

PCI Riser

Socket

Riser Card

Connector

Install PCIe Add-in Card

CAUTION:

Observe normal ESD precautions

when installing add-in cards.

Remove ﬁller panel from the add-in

card slot.

Insert add-in card until it seats in the

riser connector.

Secure add-in card with screw as

shown.

Riser Connector

REMOVE Filler Panel

Add-in Card

Finishing Up

Before installing your operating system, you must ﬁnish your system

installation and connect back panel I/O connectors and AC power.

CAUTION: This unit must

be operated with the TOP

COVER installed to ensure

proper cooling.

2. Connect your keyboard, mouse, video

and other I/O cables/devices as shown.

Then connect the AC power cord.

1. Make sure you have replaced the system cover.

Network

NIC1

Network

NIC2

USB

0, 1

USB

2, 3

Serial

Port A

Video

AC Power

PCI-E Card

Platform Cabling Diagram

Server Board SATA

Connector Legend

Server Board

Power Supply

Front Panel Board

Backplane

Front Panel USB

Power to Server Board (Main)

Power to Backplane

Power to Server Board (CPU)

Optical Device to Power Supply

PSU Management Bus to AUX

Front Panel

HDD 0 to Server Board SATA 0

HDD 1 to Server Board SATA 1

HDD 2 to Server Board SATA 2

HDD 3 to Server Board SATA 3

Link to Backplane SGPIO

Blower Fan #1 Power

Blower Fan #2Power

Blower Fan #3 Power

Optical Device SATA Data Cable

DIMM A2

DIMM A1

DIMM B2

DIMM B1

CPU

HDD 0 HDD 1 HDD 2 HDD 3

Optical Device

H I J

N O P

Available Documents

Technical Product Speciﬁcation

Quick Reference Label

Quick Start User Guide/System Conﬁguration

Guide

Additional Reference documents available at:

http://www.intel.com/support/motherboards/server

A complete list of accessories and spares can be found at:

http://www.intel.com/support/motherboards/server

Optional Accessories/Spares and Order Codes

Value Rail kit

AXXVRAIL

SATA Slim-line DVD

AXXSATADVDROM

Intel

Remote Management Module 4

Intel

Remote Management Module 4 Lite

Intel

SAS Entry RAID Module

AXXRMM4

Intel

Trusted Platform Module

AXXRMM4Lite

AXXTPME3

AXX4SASMOD

Install and Cable Optical Device (optional)

Remove the security screws.

Remove the Filler Panel.

CAUTION:

To maintain proper system cooling,

a ﬁller blank must be

installed if you do

not install a device

at this location.

Pull the power and data cables through

the front of the chassis opening.

Connect the cables as shown.

Rear View

of Optical

Drive

Insert optical device assembly into front

panel opening and push all the way until

it stops .

Install the plastic latch on the rear side of

the drive and ﬁx it with two screws.

IMPORTANT NOTE: Refer to the Cabling Diagram below for connection

locations and cable routing.

Data

Power

Optical

Drive

Optical

Device Tray

Assembly

Install Hard Drives/Carriers

Slide the carrier away from the chassis.

Attach the hard drive to the

carrier with four screws as shown.

Note: Hard drive 3 location is shown above.

Remove the drive carrier by pressing the

green button and opening the lever.

Remove the air baffle and save for

future use.

TOP

BREAK OFF TAB

BEFORE MOUTING

2.5´´ HARD DRIVE

3.5´´ HDD

With the lever open, insert the hard disk drive assembly into the chassis

opening and push until the locking lever engages.

Push in the lever to lock it into place.

CAUTION: If you install less

than three drives or devices,

empty drive bays must be

occupied by carriers with baffles to maintain

proper system cooling.