Intel® System Configuration Utility User Guide Syscfg Version 5.
Legal Statements INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS FOR THE PURPOSE OF SUPPORTING INTEL DEVELOPED SERVER BOARDS AND SYSTEMS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT.
Contents 1 Introduction ................................................................................5 1.1 Operating Systems Supported ................................................................... 6 1.2 Target Audience....................................................................................... 9 1.3 Related Documents .................................................................................. 9 1.4 Terminology ................................................................
.4.7 email Alert Configure (/eac) for S55xx platforms .............................34 4.4.8 email Alert Enable (/eae) for S55xx and S3420GP platforms .............34 4.4.9 help (/h) ...................................................................................35 4.4.10 LAN Alert Configuration (/lac).......................................................36 4.4.11 LAN Alert Enable (/lae) ................................................................36 4.4.12 LAN Configuration (/lc) ........
1 Introduction The Intel® System Configuration Utility (Syscfg) is a command-line utility that can be used to save and restore BIOS and firmware settings to a file or to set and display individual settings. This User Guide provides a command reference for version 4.0.x and 5.0.x of the Syscfg.
1.1 Operating Systems Supported This version of the utility supports the Operating System versions listed in the following table. Refer to the Tested Hardware and Operating System List for your server board to determine which operating systems are supported on your server board: Table 1. Operating Systems Supported Platforms System Configuration Utility Version S5000PAL, S5000PSL, S5000VSA, S5000VCL, SC5400RA 2.0.
Platforms System Configuration Utility Version Operating Systems/Preboot environment supported bit) Red Hat Enterprise Linux* AS 5 (em64T) SUSE Linux* Enterprise Server 9 (32 bit) SUSE Linux* Enterprise Server 9 (em64T) SUSE Linux* Enterprise Server 10 (32 bit) SUSE Linux* Enterprise Server 10 (em64T) S5400SF 4.0.2 WinPE* version 2005 (Released with Microsoft Windows* Server 2003, Service Pack 1 [SP1] and Windows XP*, Service Pack 2 [SP2]) MSDOS 6.22 EFI 1.
Platforms System Configuration Utility Version Operating Systems/Preboot environment supported Red Hat Enterprise Linux* AS 5 (64 bit) SUSE Linux* Enterprise Server 10 (32 bit) SUSE Linux* Enterprise Server 10 (em64T) S5000AL and SR1530AH platform series 4.0.
Platforms System Configuration Utility Version Operating Systems/Preboot environment supported Windows* Server 2008 Enterprise (32bit) Windows* Server 2008 Enterprise (EM64T) Windows* XP SP3 (32 bit) Windows PE * 2004 (1.5) - Built from Windows XP* Professional with Service Pack 2 (SP2) Windows PE* 2005 (1.6) - Built from Windows* Server 2003 with Service Pack 1 (SP1). Windows PE* 2.0 - built from Windows Vista, 32 bit Windows PE* 2.
1.4 Terminology The following table lists the terminology used in this document and the description: Table 2.
Term Definition HSC Hot-swap controller I-cache Instruction cache. Processor-local cache dedicated for memory locations retrieved through instruction fetch operations.
Term Definition PSMI Power Supply Management Interface PWM Pulse Width Modulation. The mechanism used to control the speed of system fans. RAM Random Access Memory RAS Reliability, availability, and serviceability RC4 Rivest Cipher 4. A stream cipher designed by Rivest for RSA data security, now RSA security. It is a variable key-size stream cipher with byte-oriented operations. The algorithm is based on a random permutation.
2 Using the Intel® System Configuration Utility Syscfg is a command-line scriptable utility that can be used to save and restore BIOS and firmware settings to a file, or to set and display individual BIOS settings. Syscfg may be used in a script to automate the process of configuring multiple servers. Few commands may not be supported on all platforms due to limitations in the platform firmware /BIOS. The description of each command will describe any limitations.
3 Quick Start Instructions This section details the quick start instructions for configurations. 3.1 Installation A. Linux a. Boot into Linux unzip the "SyscfgVXXX_BuildXX_RHEL.zip" or "SyscfgVXXX_BuildXX_SUSE.zip",file into a folder on your hard drive. After unzip "SysCfg_RHEL" or "SysCfg_SUSE" folder will be generated The syscfg directory will have the following files. • • • • • • • • • • install-smi-drv smi-2.0.2-1.i386.rpm ReleaseNotes.txt smi.c smi.h Makefile-2.4 Makefile-2.
• • • • • • • • • • • • • • bioscfg.str bootdev.str fwadvcfg.str HelpBmc.str HelpMbmc.str lancfg.str pefcfg.str powercfg.str sercfg.str solcfg.str syscfg.str system.str usercfg.str ReleaseNotes.txt b. Set the syscfg path variable SYSCFG_PATH. e.g:- set SYSCFG_PATH fs0:\ where syscfg_efi is the folder containing all the files mentioned above. c. Run 'syscfg' commands from the location where the files are copied. d.
g. From the command prompt go to SysCfg Release folder and run the desired commands for the utility h. To uninstall SYSCFG run the following commands manually • • 3.2 Delete the contents of the directory where the utility is installed. Manually uninstall drivers from the Device manager Saving a Configuration From S55XX platform series the utility supports saving BIOS and FW settings both in binary and in text mode (from a text file, known as INI file).
To restore a configuration, do the following: 1. Boot the system to one of the supported Operating Systems. 2. Change to the directory containing the syscfg executable. (The saved configuration file should also be located in this directory.) 3. To restore the saved BIOS settings in Windows*, Windows Pre-installation Environment*, or EFI, type: syscfg /r filename.scf /b In Linux*, type: ./syscfg /r filename.scf /b 3.4 Displaying Syscfg Help To display syscfg help, type: syscfg /h 3.
4 Using Commands This section lists the Generic commands/switches, BIOS, and Firmware commands and their tasks. 4.
4.2 Generic Commands/Switches 4.2.1 Information (/i) syscfg /i [filename.SCF] File name for a System Configuration File (.SCF) in the current working directory. If the filename is not specified, the command displays the BIOS and firmware versions of the current system. Filename Displays the BIOS and firmware versions of the system or the saved BIOS and firmware settings in a System Configuration File. Examples: syscfg /i syscfg /i bd2.scf 4.2.
4.2.3 Restore (/r) syscfg /r [filename.SCF] {/f | /b | /f /b} Filename of the syscfg configuration file (.SCF) in the current working directory. If no filename is specified, the default filename syscfg.scf is used. The filename suffix must be .SCF. Filename Restore the firmware settings. (See Appendix A for a list of the settings that are restored.) /f Restore the BIOS settings. (See Appendix A for a list of the settings that are restored.) /b Restores the BIOS and firmware settings from a SCF file.
4.2.4 Save (/s) syscfg /s [filename.SCF] {/f | /b | /f /b} File name to be used for the syscfg configuration file (.SCF) in the current working directory. If no filename is specified, the default file name syscfg.scf is used. The filename suffix must be .SCF, or, if omitted, syscfg will add the .SCF suffix. The filename should consist of only alphanumeric characters. Filename /f Save the firmware settings. (See Appendix A for a list of the settings that are saved.) /b Save the BIOS settings.
4.2.
USER Displays the BMC user settings. Channel_ID IPMI Channel ID. LAN_Alert_Destination_Index Enter the LAN Alert Destination Index. Dial_String_Index Enter the Serial Modem Dial String Index. Page_Destination_Selector Enter the Page Destination Selector. Dial_String_Selector Enter the Dial String Selector. Filter_Table_Index Enter the Filter Table Index. Policy_Table_Index Enter the PEF Policy Table Index.
4.3 BIOS Commands This section lists the BIOS Commands. 4.3.1 BIOS Administrator Password (/bap) syscfg /bap {old_password | ""} [new_password | ""] The maximum length of the password is seven characters. The password cannot have characters other than alphanumeric (a-z, AZ, 0-9) and is case insensitive. Use two double quotes ("") to represent a null password. old_password new_password Sets or clears the BIOS Administrator password.
4.3.2 BIOS Boot Order (/bbo) syscfg /bbo [device_number [device_number […] ] ] The current ordinal number of the BIOS boot device (1 is the first device, 2 is the second device, and so on.). To change the order, specify an order for the device numbers (for example, if you specify “2 1 4 3” then the second boot device will be the first boot device after the command is executed. device_number Refer to the Product Guide for your Intel® Server Board for more information on BIOS Setup options.
Here, EFI is now the first system boot option and Network boot is the second option, followed by CD/DVD, Hard Disk Drive and so on. Changing the order of bootable devices within a particular boot device class syscfg /bbo NW 2 1 Here, IBA GE Slot 0101 v1327 has been chosen as the first bootable option and IBA GE Slot 0100 v1327 has been chosen as the second bootable option in network boot device category. Note: 1. Reordering boot devices using /bbo should be followed by a system reset as per IPMI spec.
Note: If the /bcr option is enabled, the quiet boot option cannot be enabled. 4.3.4 Configure BIOS Settings (/bcs) syscfg /bcs [BIOS_Group_Name] BIOS_Setting_Name Value [BIOS_Setting_Name Value […] ] BIOS_Setting_Name The name of the BIOS settings on the BIOS Setup screen. Refer to the Technical Product Specification for your server board for the BIOS Setup setting names. The name of the page in the BIOS Setup screen.
4.3.6 BIOS Post Error Pause (/bpep) syscfg /bpep {enable | disable} Enables or disables the pause on POST error BIOS option. enable, disable Enable pause on POST error in BIOS option. Examples: syscfg /bpep enable syscfg /bpep disable 4.3.7 BIOS Quiet Boot (/bqb) syscfg /bqb {enable | disable} Enables or disables the BIOS Quiet Boot feature. enable, disable Enable quiet boot option in the BIOS. The BIOS default is to enable the quiet boot option.
If you set or change the BIOS User password, you cannot change any other BIOS option using syscfg except the BIOS User and Administrator passwords. Refer to the Product Guide for your Intel® Server Board for more information on BIOS Setup options. Examples: syscfg syscfg syscfg syscfg /bup /bup /bup /bap "" kwm93a3 kwm93a9 lqts284 lqts284 "" "" lqts284 /bup "" kwm93a3 Note: The /bup option can only be used if system has a valid Administrator password set.
2. The attributes 0, 1, 4 and 5 are not supported with this switch. 3. The supported attributes are 2, 3, 6, and 7 Attributes Description.
4.4 Firmware Commands This section lists the Firmware commands. 4.4.1 Channels (/c) syscfg {/c | /channel} [channel_ID { 1 {none | straight | MD5} | 2 {none | straight | MD5 } | 3 {none | straight | MD5 } | 4 {none | straight | MD5 } | 5 {enable | disable} | 6 {enable | disable} | 7 {disabled | preboot | always | shared} | 8 {callback | user | operator | admin} | 9 {enable | disable} } ] BMC channel ID number. Channel_ID Selects the authentication types for callback privilege level.
4.4.2 Clear SEL (/csel) syscfg {/csel | /clearSEL} Clears the System Event Log (SEL). syscfg /csel syscfg /clearSEL 4.4.3 Date and Time (/dt) syscfg {/dt | /timeofday} hh:mm:ss mm/dd/yyyy Hours (24 hour clock), minutes, and seconds. hh:mm:ss Month, day, and year. mm/dd/yyyy Sets the time of day stored in the Real Time Clock (RTC) by the BIOS. Example: syscfg /dt 18:45:00 12/20/2007 4.4.
Sender machine name. This string identifies the managed server to the SMTP server. Sender_Name Sets the sender machine name for SMTP email alerts from the current server. This command is not supported on Intel® Server Boards X38MLST and S3200SH. Example: syscfg /eae dupont01 4.4.6 email Alert Map (/eam) syscfg {/eam | /emailalertmap} Channel_ID Alert_Destination_Index email_Alert_Index Channel_ID IPMI channel ID number (LAN channel). Alert_Destination_Index Alert Destination Index.
4.4.7 email Alert Configure (/eac) for S55xx platforms syscfg {/eac | /emailalertconf} SMTP_Configurtion_Index {0|1 | 2 | 3|4|5|6|7} ASCII_String Channel number SMTP_Configuration_Index {0|1 | 2 | 3|4|5|6|7} 1 to n. An index into the SMTP configuration table in firmware. The maximum number n depends on the firmware on your server board (refer to your server documentation for details).
Sender machine name. This string identifies the managed server to the SMTP server. Sender_Name Channel number Valid LAN channel number Sets the sender machine name for SMTP email alerts from the current server. Example: syscfg /eae dupont01 3 4.4.9 help (/h) syscfg {/h | /?} {lan | user | serial | pef | sol | power | channel | system | advancedfwcfg | bios} lan | user | serial | pef | sol | power | channel | system | fwadvcfg | bios Displays help in the specified area.
4.4.10 LAN Alert Configuration (/lac) syscfg {/lac | /lanalertconf} Channel_Id Alert_Destination_Index Alert_Destination_IP_Address {Alert_ID_MAC_Address | “resolve”} {enable | disable } {enable | disable} {1..7} {1..255} {SNMP | SMTP} Channel_ID IPMI Channel number. Alert_Destination_Index Index into the Alert Destination table. Alert_Destination_IP_Address Alert_ID_MAC_Address IP address of the alert destination in the dot separated decimal value format: n.n.n.
Backup_Gateway_IP_ Address Gateway IP Address for the specified LAN channel Backup_Gateway_MAC_Address Gateway MAC Address for the specified LAN channel or “resolve” Notes: • The Gateway_MAC_Address and Backup_Gateway_MAC_Address may optionally be set to “resolve”. If set to “resolve”, syscfg will attempt to resolve the MAC address before writing any values to firmware. If the MAC Address resolution fails, syscfg quits, without writing, and prints an error message.
4.4.12 LAN Configuration (/lc) syscfg {/lc | /lanconf} Channel_ID {2a {none | straight | MD5} | 2b {none | straight | MD5} | 2c {none | straight | MD5} | 2d {none | straight | MD5} | 3 IP_Address | 4 {static | DHCP} | 6 IP_Address | 10 {enable | disable} | 10b {enable | disable} | 11 {0..
13 valid option when the source is set to DHCP.) Selects Gateway MAC Address 14 Selects Backup Gateway IP Address 15 Selects Backup Gateway MAC Address 16 Selects Community String Up to a 64 byte ASCII string (printable characters in the range 0x21 to 0x7e) DHCP Host Name String C7 Configures the LAN settings on a specific channel. This option is similar to /lac, but it is used to only configure one parameter at a time.
4.4.13 LAN Enable (/le) syscfg {/le | /lanenable} Channel_ID {dhcp | {static IP_Address Subnet_Mask}} Channel_ID BMC LAN Channel ID static | dhcp IP Address source IP_Address IP Address Subnet_Mask Subnet mask Configures the LAN channel used by the BMC on the specified channel. See IPMI 2.0 Specification for more information. . Examples: syscfg /le 1 dhcp syscfg /le 1 static 10.30.240.21 255.255.255.0 4.4.
Index into the PEF filter table for a particular filter. Filter_table_index Enable specified filter. enable | disable none | alert | pdown | reset | pcycle | diagint PEF Action. Enable multiple actions by using a plus sign to concatenate the values. none may not be combined with other options. pdown means “power down.” pcycle means “power cycle.” Policy number. This number maps to the Alert Policy Table. (See also /pefp option.) 1..
NEXT_C = if an alert was successfully sent to the previous destination attempted, do not send an alert to the destination indicated in the policy table entry specified in argument 1, but go to the next policy table entry with the same policy number but that will send an alert on a different channel.
Note: This command should be used by itself. Do not issue Syscfg commands for a few seconds after this command to allow the BMC to initialize. 4.4.19 Restore Firmware Settings (/rfs) syscfg {/rfs | restorefirmwaresettings} Restores the factory default Baseboard Management Controller settings. Example: syscfg /rfs Note: This command should be used by itself. Do not issue Syscfg commands for a few seconds after this command to allow the BMC to initialize.
A for a list of the settings that are saved.) Save the BIOS settings. (See Appendix A for a list of the settings that are saved.) /b Saves the BIOS and firmware settings to a SCF file. Examples: syscfg /s ini /f /b syscfg /s saved.ini /f 4.4.22 Serial Configuration (/sc) syscfg {/sc | /serialconf} Channel_ID { [2a {None | Straight | MD5}] [2b {None | Straight | MD5}] [2c {None | Straight | MD5}] [2d {none | Straight | MD5}] [3a {enable | disable}] [3b direct] [4 {0..
Channel_ID IPMI Channel ID (this must be 4 for all supported server boards). 2a Authentication type for Callback privilege level. Multiple privilege levels may be specified by using the plus sign (see example below). 2b Authentication type for User privilege level. Multiple privilege levels may be specified by using the plus sign (see example below). 2c Authentication type for Operator privilege level. Multiple privilege levels may be specified by using the plus sign (see example below).
syscfg /sc 4 2d none+straight+MD5 4.4.23 Serial Dial String (/sds) syscfg {/sds | /serialdialstring} Channel_ID Dial_String_Index Dial_string IPMI Channel ID (this must be 4 for S5000PAL, S5000PSL, and S5000PSA server boards) Channel_ID Dial String Index Dial_String_Index ASCII string with the modem dial command and phone number Dial_String Sets the serial modem dial string used by the BMC on the specified channel. See IPMI 2.
4.4.
4.4.27 Serial Over LAN Enable (/sole) syscfg {/sole | /soleenable} Channel_ID {enable | disable} {user | operator | admin} {9600 | 19200 | 38400 | 115200} {0..7} {0..2550} Channel_ID IPMI Channel ID enable | disable SOL enable user | operator | admin Privilege Level Limit 9600 | 19200 | 38400 | 115200 Baud Rate 0..7 Retry count Retry interval in milliseconds, rounded to the nearest 10 ms 0..2550 Enables Serial Over LAN (SOL) on the specified LAN channel. See IPMI 2.
4.4.29 Users (/u) syscfg {/u | /user} User_ID User_name Password User ID. Use a decimal integer in the range [1..n], the maximum value for n is 5. That is, only five users are supported irrespective of the platforms. User ID 1 is usually the anonymous user. User_ID BMC User name consisting of up to 16 ASCII characters in the range 0x21 to 0x7e, except “[” and “]”. Use “” to leave user name as anonymous. User_name User BMC Password. ASCII string of up to 20 characters.
4.4.30 User Enable (/ue) syscfg {/ue | /userenable} User_ID {enable | disable} Channel_ID User ID. Use a decimal integer in the range [1..n] where n is the number of users supported by the platform BMC. User ID 1 is usually the anonymous user. User_ID enable | disable Enable or disable the specified user Channel_ID IPMI Channel ID Enables or disables the BMC user on the specified BMC channel. See IPMI 2.0 Specification for more information on user configuration settings.
A Appendix A: IPMI Channel Assignments The following table lists the Intel® Server Boards and their corresponding IPMI Channel assignments: Server Board IPMI Channel Assignment Intel® S5000 and S7000 Series Channel Channel Channel Channel 1 2 3 4 Baseboard LAN Channel A Baseboard LAN Channel B Optional Intel® RMM NIC Serial Channel Intel® Server Board X38MLST and S3200SH Series Channel 1 Baseboard LAN Channel A Intel® S5500 Series, and Intel® S3420GP Series Channel 1 Channel 3 Baseboard LAN Cha
B Appendix B: Saved Firmware Settings This section describes firmware settings that are saved and restored with syscfg in binary and INI formats. Binary Format The following table lists the firmware settings that are saved and restored with syscfg in binary formats. Table 3.
Component Setting Retry Interval User Settings User Name User Password Privilege Level Limit Callback Status Link Authentication Enable IPMI messaging enabled User Payload Platform Event Filter Settings † PEF Enable Event Message for PEF Action Startup Delay Alert Startup Delay Global Control Actions Event Filters Alert Policies Serial Settings† Paging Enable Per Message Authentication User Level Authentication Access Mode Privilege Level Limit Community String Authentication Types Connection Mode F
Component Setting Modem Ring Duration Modem Call Retry Interval Modem Ring Dead Time Ping During Callback Modem Enabled Callback Blackout Interval Modem Dial Command Modem Hang-up Command Modem Escape Command System Phone Number Terminal Mode Enable Terminal Line Edit Enable Terminal Delete Control Terminal Echo Enable Terminal Handshake Enable Terminal Newline Output Sequence Terminal Newline Input Sequence Dial String Length Destination Dial Strings † Serial Paging Alert Settings Alert Acknowledge Enab
Component Setting Subject Line LAN Alert Destination/SNMP Alert Index Mapping Intel® System Configuration Utility – User Guide 55
Example of INI File Instructions for using INI file: ; ; ; ; ; ; ; ; Section Header – must not be edited – could lead unpredictable behavior.
Operator, Admin, NoAccess UserAccessCh1=Disable Disable SOLEnableCh1=Enable Disable PrivilegeChl3=Admin Operator, Admin, NoAccess UserAccessCh3=Disable Disable SOLEnableCh3=Disable Disable PrivilegeChl4=NoAccess Operator, Admin, NoAccess UserAccessCh4=Disable Disable SOLEnableCh4=Disable Disable [USERS::USER2] UserName=root be edited GlobalUserStatus=Disable Disable PrivilegeChl1=Admin be edited UserAccessCh1=Enable be edited SOLEnableCh1=Disable be edited PrivilegeChl3=Admin be edited UserAccessCh3=Enable
Disable SOLEnableCh1=Enable Disable PrivilegeChl3=Admin Operator, Admin, NoAccess UserAccessCh3=Disable Disable SOLEnableCh3=Enable Disable PrivilegeChl4=NoAccess Operator, Admin, NoAccess UserAccessCh4=Disable Disable SOLEnableCh4=Disable Disable ; Options: Enable or ; Options: User, ; Options: Enable or ; Options: Enable or ; Options: User, ; Options: Enable or ; Options: Enable or [USERS::USER4] UserName=test2 ; ASCII printable characters in the range of 0x21 to 0x7E.
Disable PrivilegeChl3=Admin Operator, Admin, NoAccess UserAccessCh3=Disable Disable SOLEnableCh3=Enable Disable PrivilegeChl4=NoAccess Operator, Admin, NoAccess UserAccessCh4=Disable Disable SOLEnableCh4=Disable Disable [PEF] PEFEnable=Enable Disable [PEF::FILTERS] Filter1=Disable Disable Filter2=Disable Disable Filter3=Disable Disable Filter4=Disable Disable Filter5=Disable Disable Filter6=Disable Disable Filter7=Disable Disable Filter8=Disable Disable Filter9=Disable Disable Filter10=Disable Disable Filte
[CHANNEL::LAN1] AlertEnable=Enable ; Options: Enable, Disable PerMessageAuthentication=Enable ; Options: Enable, Disable UserLevelAuthentication=Enable ; Options: Enable, Disable AccessMode=AlwaysAvailable ; Options: Disable, AlwaysAvailable, AccessShared PrivilegeLevelLimit=Admin ; Options: User, Operator, Admin CommunityString=INTEL ; Upto 16 bytes, no space allowed ARPEnable=Disable ; Options: Enable, Disable ARPResponse=Enable ; Options: Enable, Disable ARPInterval=0 ; Decimal value between 0 & 255.
AccessMode=AlwaysAvailable ; Options: Disable, AlwaysAvailable, AccessShared PrivilegeLevelLimit=Admin ; Options: User, Operator, Admin CommunityString=INTEL ; Upto 16 bytes, no space allowed ARPEnable=Disable ; Options: Enable, Disable ARPResponse=Enable ; Options: Enable, Disable ARPInterval=0 ; Decimal value between 0 & 255. This values is in milliseconds. Input value rounded down to the nearest 500ms value DHCPEnable=Disable ; Options: Enable or Disable. If 'Disable' static IP will be used HostIP=0.0.0.
SOLEnable=Enable ; Options: Enable, Disable PrivilegeLevelLimit=User ; Options: Admin, User, Operator SolNumberOfRetries=7 ; Decimal value in the range 0-7 SolRetryInterval=500 ; Decimal value in the range of 0-2559 rounded down to the nearest unit of 10. In milliseconds SolBaudRate=38400 ; Options: 9600, 19200, 38400, 57600, 115200.
[BIOS] [BIOS::ADVANCED] [BIOS::ADVANCED::MEMORY CONFIGURATION] [BIOS::ADVANCED::MEMORY CONFIGURATION::MEMORY RAS AND PERFORMANCE CONFIGURATION] Select Memory RAS Configuration=0 ;Options: 1=Mirroring: 0=Maximum Performance NUMA Optimized=1 ;Options: 1=Enabled: 0=Disabled [BIOS::ADVANCED::MASS STORAGE CONTROLLER CONFIGURATION] Onboard SATA Controller=1 ;Options: 1=Enabled: 0=Disabled SATA Mode=0 ;Options: 2=SW RAID: 1=AHCI: 3=COMPATIBILITY: 0=ENHANCED [BIOS::ADVANCED::SERIAL PORT CONFIGURATION] [BIOS::ADVANC
[BIOS::ADVANCED::PCI CONFIGURATION] Maximize Memory below 4GB=0 0=Disabled Memory Mapped I/O above 4GB=0 0=Disabled Onboard Video=0 0=Enabled Dual Monitor Video=0 0=Disabled Onboard NIC1 ROM=1 0=Disabled Onboard NIC2 ROM=1 0=Disabled ;Options: 1=Enabled: ;Options: 1=Enabled: ;Options: 1=Disabled: ;Options: 1=Enabled: ;Options: 1=Enabled: ;Options: 1=Enabled: [BIOS::ADVANCED::SYSTEM ACOUSTICS AND PERFORMANCE CONFIGURATION] Set Throttling Mode=0 ;Options: 2=CLTT: 1=OLTT: 0=Auto Altitude=900 ;Options: 3000=H
[BIOS::PCI EXPRESS PORT 1] Hot Plug Capable=0 0=Disable PCIe Port VPP=0 0=Disable VPP SMBUS Address=2 4=4: 3=3: 2=2: 1=1: 0=0 [BIOS::PCI EXPRESS PORT 2] Hot Plug Capable=0 0=Disable PCIe Port VPP=0 0=Disable VPP SMBUS Address=3 4=4: 3=3: 2=2: 1=1: 0=0 [BIOS::PCI EXPRESS PORT 3] Hot Plug Capable=0 0=Disable PCIe Port VPP=0 0=Disable VPP SMBUS Address=4 4=4: 3=3: 2=2: 1=1: 0=0 [BIOS::PCI EXPRESS PORT 4] Hot Plug Capable=0 0=Disable PCIe Port VPP=0 0=Disable VPP SMBUS Address=5 4=4: 3=3: 2=2: 1=1: 0=0 [BIOS::P
Hot Plug Capable=0 0=Disable PCIe Port VPP=0 0=Disable VPP SMBUS Address=3 4=4: 3=3: 2=2: 1=1: 0=0 [BIOS::PCI EXPRESS PORT 8] Hot Plug Capable=0 0=Disable PCIe Port VPP=0 0=Disable VPP SMBUS Address=4 4=4: 3=3: 2=2: 1=1: 0=0 [BIOS::PCI EXPRESS PORT 9] Hot Plug Capable=0 0=Disable PCIe Port VPP=0 0=Disable VPP SMBUS Address=5 4=4: 3=3: 2=2: 1=1: 0=0 [BIOS::PCI EXPRESS PORT 10] Hot Plug Capable=0 0=Disable PCIe Port VPP=0 0=Disable VPP SMBUS Address=6 4=4: 3=3: 2=2: 1=1: 0=0 ;Options: 1=Enable: ;Options: 1=E
1=Disabled Core Multi-Processing=0 0=All Execute Disable Bit=1 0=Disabled Intel(R) Virtualization Technology=0 0=Disabled Intel(R) VT for Directed I/O=0 0=Disabled Hardware Prefetcher=0 1=Disabled Adjacent Cache Line Prefetch=0 1=Disabled Direct Cache Access (DCA)=1 0=Disabled [BIOS::MAIN] Quiet Boot=1 0=Disabled POST Error Pause=0 0=Disabled ;Options: 2=2: 1=1: ;Options: 1=Enabled: ;Options: 1=Enabled: ;Options: 1=Enabled: ;Options: 0=Enabled: ;Options: 0=Enabled: ;Options: 1=Enabled: ;Options: 1=Enabled
Baud Rate=0 3=57.6k: 2=38.4k: 1=19.2k: 0=9.6k Terminal Type=0 2=VT100+: 1=VT100: 0=PC-ANSI Legacy OS Redirection=0 0=Disabled ;Options: 4=115.2k: ;Options: 3=VT-UTF8: ;Options: 1=Enabled: [BIOS::BOOTORDER] 1=KingstonDataTraveler 2.01.
