Quick Start Guide Front

ManualsBrandsIntel ManualsOtherIntel Server Chassis SC5400BASE

Intel is a registered trademark of Intel Corporation or its

subsidiaries in the United States and other countries.

*Other names and brands may be claimed as the property

reserved.

Warning

Read all caution and safety

statements in this document

before performing any of the

instructions. Also see the Intel

Server Board and Server Chassis

Safety Information document at:

http://support.intel.com/support/

motherboards/server/sb/cs-010770

.htm for complete safety information.

Warning

Installation and service of

this product to be performed

only by qualified service

personnel to avoid risk of injury from

electrical shock or energy hazard.

Tools Required

Caution

Observe normal ESD

[Electrostatic Discharge]

procedures during system

integration to avoid possible

damage to server board and/or

other components.

Anti-static

wrist strap

Phillips*

screwdriver

Intel® Server Chassis

SC5400/SC5400LX/SC5400BRP

Quick Start User's Guide

Thank you for buying an Intel® Server Chassis. The following

information will help you assemble your Intel

Server Chassis

and install components.

If you are not familiar with ESD [Electrostatic Discharge] procedures used

during system integration, see the complete ESD procedures described in

your User Guide. For more details on Intel

Server Products, please see:

www.intel.com/go/serverbuilder

This guide and other supporting documents are located on the web at

http://support.intel.com/support/motherboards/server/chassis/SC5400

Remove the Bezel Assembly

Release two plastic tabs.

Note: The bezel assembly consists of two

components, a front door and a sub-bezel.

Rotate bezel assembly no more than 40-degrees

outward. If bezel assembly does not immediately

disconnect from the chassis, then remove by tapping

the left-hand side of the bezel assembly to disengage

the bezel hooks on the right-hand side of the chassis.

At a 40 degree angle, push bezel assembly away

from the chassis.

CAUTION: Do not rotate the bezel assembly

more than 40° or you will damage the bezel

hooks at the right side of the bezel assembly.

Install Feet (pedestal only)

Insert rubber foot into chassis hole.

Note: This step applies to your chassis if configured as a

pedestal system. If you plan to configure your chassis as

a rackmount system, go to Step 2.

Note: Repeat above steps until all four feet are installed.

Secure foot by inserting pin through the rubber foot.

Remove the Side Cover

Push in latch and

remove as shown.

Remove screw securing side cover.

Note:

Chassis

with a fixed

power supply

is shown. Your

chassis may

differ slightly.

Note: Device slides are "tool-less"

and do not require screws.

Insert device/slide assembly into chassis bay until

slides lock into place.

Slide Latch

Metal

Ta b

Remove filler panel/slide assembly as shown in Step 10.

Press slide tabs into device mounting holes.

Connect power and

data cables as shown.

Install CD-ROM

Drive (optional)

Remove Device

Tray and Device

Slides

Press each slide inward to release and pull

slides and device tray out of device bay.

Remove slides from tray as shown.

IMPORTANT!

Disregard this step

if you do not plan

to install a device

at this location.

Device Tray

Device

Slides

Install USB

Floppy/

CD/DVD

Slimline

Combo

(optional)

See the installation instructions

that came with your USB Floppy/CD

Slimline combo kit to install this

device. This device must be

installed in the top slot of the

upper bay.

Note: If you plan to configure

your system for a rack mount

installation, see the instructions

that come with your rack mount

kit for proper device orientation

in the upper bay.

Install Rack

Conversion

Kit (optional)

For complete steps on

rack conversion, see

the Rack Conversion

Kit Installation

Guide.

Flat Blade

screwdriver

Supported Server Boards

Your

Intel

Server Chassis SC5400BASE supports

the following Intel

Server Boards:

Your

Intel

Server Chassis SC5400LX

or SC5400BRP supports the following Intel

Server

Boards:

See your

Intel

Server Board documentation

for specific component integration requirements

not addressed in this chassis Quick Start User’s

Guide.

■ Intel

Server Board S5000PSL

■ Intel

Server Board S5000XVN

■ Intel

Server Board S5000XSL

Remove Hot-swap Fans

(SC5400LX only)

Press latch; place finger into handle and pull out

hot-swap fans.

Fan

Latch

MOVE TRAY TO

BOTTOM BAY!

Install

Additional

Drive Bays

For installing SAS/SATA fixed or

hot-swap drives into the drive bays,

refer to the

Drive Cage Upgrade Kit

Installation Guide.

6-drive

hot-swap

drive bay

4-drive

fixed

drive bay

Remove Device Tray

and Device Slides

Press each slide inward to release. Pull

slides and device tray out of device bay.

Remove slides from tray as shown.

Note:

Disregard this step

if you do not plan

to install a device

at this location.

Device Tr

Device

Slides

Remove Filler Panel

and Device Slides for

CD-ROM (optional)

Press each slide inward to release. Pull

slides and filler panel out of device bay.

Remove slides from filler panel as shown.

Note:

Disregard this step

and Step 11 if

you do not plan

to install a

CD-ROM drive.

Fille

r Panel

Device Slide

Remove the Air Ducts

Unlatch the memory air duct from the chassis by

pressing the tab. Grasp the memory air duct and

remove.

Unlatch the processor air duct from the chassis by

squeezing

the blue

touch

points.

Memory and

Processor

Air Duct

Detail

Processor

Air Duct

Memory

Air Duct

Ducts disconnect

here

Blue touch

points

Push here to release

Install and Route Data and Power Cables to Fixed Drive Bays

To Upper Device Bay

To Server Board

To 4-Drive

Cage

To 4-Drive

Cage

To 6-Drive

Cage

To 6-Drive

Cage

Power Cable Routing SAS/SATA Cable Routing

Chassis

Secondary

Side View

Note: Access openings are located

on the secondary side of the chassis

to facilitate cable routing if necessary.

Chassis Primary Side View Chassis Primary Side View

Chassis Primary Side View

Press on two plastic tabs and remove PCI add-in card

retainer to access cable routing slot.

Route longest power cables to the 6-drive bay and shorter

cables to the 4-drive bay and upper device bay.

Note: Front panel,

USB and one IDE

cable are pre-routed

by the factory. SAS

or SATA cables are

supplied with the

server board and

hot-swap drive

accessory kits.

No cables are

supplied with the

fixed drive bay kit.

PCI Add-in

card retainer

detail

Cable

Slot

Power Cable Routing Guidelines:

• P3, P4 and P5 power cables route to removable drives.

• P6, P7, P8, P9, P10, and P11 power cables to fixed drive

bays; route as appropriate.

• P12 and P13 power cables (SAS/SATA); route to fixed

drive bays as appropriate.

IDE/USB/Front Panel Cables

4/6 Drive

Bay Cables

SAS/SATA

Note: All cables route through openings located at the back wall of the chassis.

GREEN

indicates

user

installed

cable

routing.

BLUE

indicates

power

cable

routing.

Cabling Access

Openings

D38438-002

Push blue plastic release

mechanism upward to release HDD cage.

Slide hard drive cage out of chassis bay.

Note: If you plan to install fixed hard drives,

proceed to Step 13.

Remove HDD Cage(s)

(optional)

■ Intel

Server Board S5000PSL

■ Intel

Server Board S5000XSL

Summary of content (1 pages)

PAGE 1
Supported Server Boards Intel® Server Chassis SC5400/SC5400LX/SC5400BRP Quick Start User's Guide Your Intel® Server Chassis SC5400BASE supports the following Intel® Server Boards: Install Feet (pedestal only) Note: This step applies to your chassis if configured as a pedestal system. If you plan to configure your chassis as a rackmount system, go to Step 2. ■ Intel® Server Board S5000PSL ■ Intel® Server Board S5000XVN A B ■ Intel® Server Board S5000XSL Insert rubber foot into chassis hole.