Enclosure Management Cabling for Pedestal Systems with Hot-Swap Drive Enclosures

ManualsBrandsIntel ManualsOtherIntel Server Chassis SC5600LX

Enclosure Management Cabling

for Pedestal Systems with Hot-

Swap Drive Enclosures

Cabling Guide for:

 Intel

Server Chassis SC5600 and SC5650

 Intel

Server Boards S5520HC, S5500HCV, S5520SC and S5500BC

 Intel

RAID Controllers RS2SG244, RS2WG160, RS2BL080, RS2BL040, RS2PI008,

RS2MB044, RS2WC080, RS2WC040, SRCSASJV, SRCSASRB, SRCSASLS4I,

SRCSATAWB, SRCSASBB8I, SRCSASPH16I, SRCSAS18E, SRCSAS144E, SASMF8I,

SASUC8I and SASWT4I.

 Intel

Integrated RAID Module RMS2AF080, RMS2AF040, RMS2LL080, RMS2LL040

 Intel

RAID Expander Card RES2SV240

 Intel

Integrated RAID Module SROMBSASMR

 Intel

Entry RAID Module AXX4SASMOD

Revision 5.0

September, 2010

Summary of content (8 pages)

PAGE 1
Enclosure Management Cabling for Pedestal Systems with HotSwap Drive Enclosures Cabling Guide for: Intel® Server Chassis SC5600 and SC5650 Intel® Server Boards S5520HC, S5500HCV, S5520SC and S5500BC Intel® RAID Controllers RS2SG244, RS2WG160, RS2BL080, RS2BL040, RS2PI008, RS2MB044, RS2WC080, RS2WC040, SRCSASJV, SRCSASRB, SRCSASLS4I, SRCSATAWB, SRCSASBB8I, SRCSASPH16I, SRCSAS18E, SRCSAS144E, SASMF8I, SASUC8I and SASWT4I.
PAGE 2
Enclosure Management Cabling for Pedestal Systems with Hot-Swap Drive Enclosures Revision History Date April, 2009 Revision Number 3.0 Modifications Initial release for Intel S5500/S5520 series boards. September, 2009 4.0 Added new RAID controllers, modules and server systems September, 2010 5.0 Added new RAID controllers, modules and server systems ® Disclaimers ® Information in this document is provided in connection with Intel products.
PAGE 3
1. Connecting One Expander Backplane Note: Before any cabling operation, please refer to the respective RAID module or RAID controller Tested Hardware and Operating System lists, in order to confirm their compatible Intel® Server Boards or Systems. You must connect the following cables to the backplane: SATA/SAS data cables Power cables IPMB cable for updating the hot-swap controller firmware, reading the temperature, and detecting drive presence: 2.
PAGE 4
Enclosure Management Cabling for Pedestal Systems with Hot-Swap Drive Enclosures 3. Connecting One Non-Expander Backplane You must connect the following cables to the backplane: SATA/SAS data cables: − With 4-drive Non-expander backplane, RAID controller ports 0-3 must be connected to the Nonexpander backplane. Make sure port 0 is connected to slot 0, port 1 to slot 1, and so on. − With 6-drive Non-expander backplane, RAID controller ports 0-5 must be connected to the Nonexpander backplane ports.
PAGE 5
− With 4-drive Non-expander backplane, RAID controller ports 0-3 or port 8-11 must be connected to the Non-expander backplane. Make sure port 0 is connected to slot 0, port 1 to slot 1, port 8 to slot 0, port 9 to slot 1, and so on. − With 6-drive Non-expander backplane, RAID controller ports 0-5 or port 8-13 must be connected to the Non-expander backplane ports. Make sure port 0 is connected to slot 0, port 1 to slot 1, port 8 to slot 0, port 9 to slot 1, and so on.
PAGE 6
Enclosure Management Cabling for Pedestal Systems with Hot-Swap Drive Enclosures 6. Connecting Fault LED Control Cables Only non-expander backplanes (AXX6DRV3GR and AXX4DRV3GR) require Fault LED control cables. Important: Only one Fault LED control cable – either SES or SGPIO depending on the RAID controller – must be connected to a backplane. Do not connect both SES and SGPIO cables to the same backplane. This may result in unexpected behavior including RAID array failures.
PAGE 7
SRCSASPH16I SAS in-band. No drive LED control cable needed. RAID card connector: J17 (if you use port 0-7) and J18 (if you use port 8-15), white Backplane connector: SES, white Cable: 3-pin SES RS2BL080 SAS in-band. No drive LED control cable needed. RAID card connector: J11, white Backplane connector: SES, white Cable: 3-pin SES RS2BL040 SAS in-band. No drive LED control cable needed. RAID card connector: J11, white Backplane connector: SES, white Cable: 3-pin SES RS2PI008 Not supported.
PAGE 8
Enclosure Management Cabling for Pedestal Systems with Hot-Swap Drive Enclosures RMS2LL080 RMS2LL040 SAS in-band. No drive LED control cable needed. Option 1: RAID module connector: J1A1 (SES), white Backplane connector: SES, white Cable: 3-pin SES Option 2: RAID module connector: J1A2 or J1B2 (SGPIO), black Backplane connector: SGPIO, black Cable: 4-pin SGPIO SAS in-band. No drive LED control cable needed.