Quick Start Guide Back

ManualsBrandsIntel ManualsOtherIntel Server Chassis SC5600LX

Side 2

Replace Side Cover

Re-install side cover and latch securely.

Side Cover

CAUTION: This chassis must be

operated with the SIDE COVERS

installed to ensure proper cooling.

Install Hard Drives into Fixed Drive Bay

A. Open Cage Access Doors B. Remove Device Slides

C. Install Slides to Hard Drive

Note: Device slides are

"tool-less". Insert slide

tabs into hard drive

mounting holes and

press firmly into place.

D. Insert Drive/Slide Assembly

into Cage

Note: Make sure connector end of drive

faces toward the rear of the cage.

Rear

of Cage

Loosen the

captive thumb

screw, then

open the

upper door.

Open the

lower door.

Connector

end of drive

to back.

Ta b

Close cage doors and tighten captive

thrumb screw. Repeat this procedure

for each drive.

Front Panel Controls

and Indicators

A. ID Button

B. System Reset

Button

C. NIC1 LED

D. System Power

Button

E. Hard Drive

Activity LED

F. System ON

LED

G. NIC2 LED

H. ID LED

I. Status LED

J. NMI Button

Reference

Rack Mount

Conﬁguration

(optional)

If you intend to configure

your server as a pedestal

system, disregard this

step.

If you intend to configure

your server as a rack-

mount system, go to the

instructions that came

with your rack-mount kit

to complete your server

assembly.

Re-install Hot-Swap

Fans (SC5600LX only)

Slide each fan into the chassis until the latch locks

into place.

Fan

Latch

Re-install Bezel Assembly

Set chassis upright if not

already in upright position.

Close the outer bezel door.

Open the front door of the bezel assembly and

remove bezel filler panel[s] that correspond to installed devices.

Fit right edge of bezel assembly against front of chassis and

engage plastic bezel hooks into raised metal slots at chassis edge.

Rotate bezel assembly toward chassis and latch two plastic tabs on

left side of bezel assembly to chassis.

CAUTION: Do not attach bezel assembly

to chassis at MORE than a 40 degree angle.

Max

Install Fixed Cage into

Chassis

Push HDD cage into

bay until blue plastic

retention mechanism

locks into place.

Connect data and power cables

to each drive.

Install Add-in Cards

PCI Slot

Close back panel PCI add-in

card retention device.

Replace PCI add-in card retainer.

PCI Slot

Shield

Insert add-in card into

server board PCI slot.

Open back panel PCI add-in card

retention device by pressing open

from inside of chassis.

Remove PCI slot shield by

pushing out from inside of

chassis.

PCI Add-in Card

Retention Device

(located on rear of chassis)

Chassis Features and Components

Notes: • Intel

Server Chassis SC5600BRP not shown.

• Rack-mount configurations are shown in the rack-mount

conversion kit documentation.

Intel® Server Chassis

SC5600LX with Hot-

Swap Components

1. Hot-Swap Power Supply #2

2. Hot-Swap Power Supply #1

3. Rear Serial-B Connector

4. PCI Add-in Card Panel

5. Memory/Processor Air Duct

6. Hot Swap Fans - Large (2)

7. Hot Swap Fans - Small (2)

8. HDD Cage Release

Mechanisms (2)

9. Front Panel Control

10. 5.25" Device Bays (3)

11. Front Panel USB/Serial B

12. Hot-Swap Drive Cage - 4 Drive

(accessory)

13. Hot-Swap Drive Cage - 6 Drive

(accessory)

1. Fixed Power Supply

2. Rear Serial-B Connector

3. PCI Add-in Card Panel

4. Memory/Processor Air Duct

5. Fixed Fans (2)

6. HDD Cage Release

Mechanisms (2)

7. Front Panel Control

8. 5.25" Device Bays (3)

9. Front Panel USB/Serial B

10. Fixed Drive Cage - 4 Drive

(accessory)

11. Fixed Drive Cage - 6 Drive

Intel® Server Chassis

SC5600Base Components

Install Additional Hot-Swap

Power Supply Module

(optional)

Note: If your chassis has a fixed power supply, go to Step 20.

Release the latch and

remove the power

supply filler panel.

Insert power supply

module until it clicks

into place.

Latch

Install Server

Board

Open the Intel

Server Board box. Follow the

instructions in the enclosed Intel

Server

Board Quick Start User's Guide and return

to this document when finished.

Note: Follow the instructions in the RAID

card Quick Start Guide for RAID card installation

and cable routing.

Accessories and Order Codes

4-Drive SAS/SATA Bay

6-Drive SAS/SATA Bay

6-Drive SAS/SATA Bay (Expander)

4-Drive Fixed Drive Bay

Intel

Local Control Panel

AXX4DRV3GR

AXX6DRV3GR

AXX6DRV3GEXP

AXX4FIXDB

AXXLCPPED

Cable Management Arm

AXXCMA3U7U

750W Power Supply Module

AXX750WPS

Rack Conversion Accessory Kit

ARIGRACK

4-Drive SAS/SATA Bay (Expander)

AXX4DRV3GEXP

North American Power Cable

FPWRCABLENA

Tower Passive Heat Sink for the

Intel

Server Chassis SC5600LX*

FXXRGTHSINK

Finishing Up

2. Connect the AC

power cable last.

1. See your Intel

Server Board

Quick Start User's

Guide to connect

your keyboard,

mouse, video, and

other I/O cables.

Power

Serial B

I/O Connections

Intel

Server Chassis SC5600

with Fixed Power Supply

I/O Connections

Intel

Server Chassis SC5600

with Hot-Swap Power Supply

Serial B

Power

CAUTION:

750 watt and 670

watt power supplies

require a 16-gauge

power cord.

Connections for Intel® Server Board S5520HC,

S5500HCV and Intel® Workstation Board S5520SC

Note: For a non-Intel Chassis, see your chassis documentation for server board connection information.

Optional Connections

HSBP_A

HSBP_B

USB_Front Panel

SATA Connectors

SATA Software RAID 5 Key

SAS Module SAS Connectors (optional)

Serial B

SATA SGPIO

SAS Module SES (optional)

SAS Module SGPIO (optional)

SAS Software RAID 5 Key (optional)

Intel

Server Chassis SC5600Base/BRP

CPU/System Fan Connections

CPU Fan 1 Header

CPU Fan 2 Header

Chassis Fan 1 Header

Chassis Fan 2 Header

Chassis Fan 3 Header

Chassis Fan 4 Header

Chassis Fan 5 Header

(Small front chassis fan)

(Large front chassis fan)

(rear chassis fan)

Intel

Server Chassis SC5600Base/BRP

Required Connections

CPU 1 Power Connector

CPU 2 Power Connector

Main Power Connector

Auxiliary Power Connector

Front Panel Header

Intel

Server Chassis SC5600Base/BRP

Intel

Server Chassis SC5600LX

Intel

Server Chassis SC5600LX

Intel

Server Chassis SC5600LX

(Either SAS SES or SGPIO)

Preventative Maintenance Kit

ARIGTPMKIT

*This accessory is required when using the Intel

Server

Chassis SC5600LX

Document Type

Reference Documentation

Technical Product Specification

Spares and Configuration Guide

Software and Drivers

Content

In-depth technical information

Supported accessories and spares list

Up-to-date firmware, driver and utility information

These and additional reference documents can be found at: http://support.intel.com

Re-install Air Duct

Read this Before Installing the

SC5600BASE and SC5600BRP

Air Duct!

Chassis alignment holes for air duct.

Air duct alignment holes.

Align the air duct and chassis rails.

Install the air duct. Ensure that alignment

holes match up, then engage the latch.

Note: Before installing the air duct,

it is important to view the features

that interconnect or latch.

To install the air duct:

Read this Before Installing the

SC5600LX Air Duct!

Chassis alignment holes for air duct.

Air duct alignment holes.

Air duct alignment tabs.

Align the air duct and chassis rail.

Install the air duct. Ensure that

alignment holes and tabs match up,

then engage the latch.

Chassis alignment slots for air duct.

Note: Before installing the air duct, it is important

to view the features that interconnect or latch.

To install the air duct:

Air duct and chassis alignment rails.

Air duct alignment tab and matching

chassis alignment slot.

WARNING: Improper installation and

removal of the air duct can cause

damage to the server board. Install and

remove the air duct with caution.

SC5600BASE/BRP Air Duct

Inlet Filler Board Removal Detail

Warning! Remove the inlet filler board

for dual processor configuration

(SC5600Base/BRP Air Duct only)

Chassis

Alignment Rails

Air Duct

Alignment Rails

Chassis Rear Fan Bracket

SC5600LX

Air Duct

Chassis

Alignment Rails

Chassis Rear Fan Bracket

Air Duct

Alignment Rails

WARNING: Improper installation and

removal of the air duct can cause

damage to the server board. Install and

remove the air duct with caution.