IS-SNAKE DevKit Setup Manual 2014/08/07 Version 1.0 The content of this document is highly confidential and should be handled accordingly.
IS-SNAKE DevKit Setup Manual Confidential These coded instructions, statements, and computer programs contain proprietary information of Nintendo and/or its licensed developers and are protected by national and international copyright laws. They may not be disclosed to third parties or copied or duplicated in any form, in whole or in part, without the prior written consent of Nintendo.
IS-SNAKE DevKit Setup Manual Table of Contents 1 Introduction .................................................................................................................................................. 4 2 Health and Safety Information ..................................................................................................................... 5 3 Notes .......................................................................................................................................
IS-SNAKE DevKit Setup Manual 1 Introduction Thank you very much for purchasing the IS-SNAKE DevKit. This manual provides important information for you to read before using the IS-SNAKE DevKit and setup procedures. Be sure to read this manual before using the product. Keep this manual in a safe place so it can be readily accessed after setup is complete.
IS-SNAKE DevKit Setup Manual 2 Health and Safety Information To use IS-SNAKE DevKit safely, please read the following items carefully to ensure the unit does not malfunction and possibly cause a safety hazard. Do not modify or take apart the device. Doing so may result in electrocution, fire, or damage to the product or other objects. If you notice a problem, immediately stop using the unit.
IS-SNAKE DevKit Setup Manual Use of any other AC adapter may result in damage to the product. Install batteries in the correct direction. Make sure the positive and negative terminals are correctly oriented. Do not use a mix of different kinds of batteries at the same time. This could cause battery leakage, overheating, or breakage, which could damage the product.
IS-SNAKE DevKit Setup Manual 3 Notes Read the following items carefully to use the IS-SNAKE DevKit unit safely and ensure the unit does not malfunction and possibly cause a safety hazard. Do not turn off the IS-SNAKE-BOX during firmware updates. The IS-SNAKE-BOX may not function properly afterward. After turning off the power, do not immediately turn it back on again. The IS-SNAKE-BOX may not function properly afterward. After turning off the power, wait at least 10 seconds before turning it on again.
IS-SNAKE DevKit Setup Manual 4 Operating Environment This section details system requirements for IS-SNAKE DevKit. Item Description Computer x86–compatible Runs on the following operating systems. Microsoft Windows 8.1 (64-bit edition) Operating System Microsoft Windows 7, Service Pack 1 or later (32-bit and 64-bit editions) Memory The PC must have at least the minimum amount of memory recommended for the operating system.
IS-SNAKE DevKit Setup Manual 5 Setup 5.1 Downloading the Software The IS-SNAKE DevKit does not include any software. Download the software package from NTSCONLINE. See the Support section of this manual for more information. Make sure you are always using the latest version of the software. Older versions might not have access to all of the features. 5.2 Software Installation Follow the procedure below to install the software. 1. Log on to Windows with a user account that has administrator privileges.
IS-SNAKE DevKit Setup Manual The software uninstallation process does not delete software settings or window layout data. You can therefore use the software with these settings even after uninstalling and then installing an upgraded version of the software. To delete this additional data, make sure that IS-CTR-DEBUGGER, CAPTURE, EMULATOR, and MONOWRITER are all not running, and then delete the following. IS-CTR Software Package o Delete everything under the following keys in Registry Editor.
IS-SNAKE DevKit Setup Manual 5.5 Attaching the Ferrite Cores Follow the procedure below to attach the ferrite cores. Attach a ferrite core to the USB cable. Loop the cable through the core twice as shown in the figure, leaving about 5 centimeters or 2 inches from the USB-B connector. Attach a ferrite core to the AC adapter cord. Loop the cable through the core once as shown in the figure, leaving about 5 centimeters or 2 inches from the DC connector.
IS-SNAKE DevKit Setup Manual 5.6 Installing Batteries To use this product, you will need two AA alkaline batteries to power the game system's internal clock. Batteries are not included at the time of shipping, so please install them using the following procedure. 1. Make sure the IS-SNAKE-BOX is turned off, and that the AC adapter is not connected. 2. Remove the battery cover on the back of the ISSNAKE-BOX. 3. Install the batteries. Install the batteries in the direction indicated by the illustration.
IS-SNAKE DevKit Setup Manual 5.7 Replacing the Batteries If the following message appears when using the software or on the HDMI output screen, replace the batteries as described under "Installing Batteries" above: "The battery might be missing or dead. Replace the batteries." 5.8 Connecting the Hardware Follow the procedure below to set up the hardware. 1. Make sure that the power switches of the IS-SNAKE-BOX units are in the OFF position. 2. Connect the controller to the ISSNAKE-BOX. 3.
IS-SNAKE DevKit Setup Manual 4. Attach the antenna to the ANTENNA port on the back of the IS-SNAKEBOX, as illustrated. 5. To use HDMI output, connect an HDMI cable to the HDMI port on the back of the IS-SNAKE-BOX. 6. To use the IS-CTR-DEBUGGER software, insert a USB cable into the DEBUGGER USB port on the back panel of the IS-SNAKE-BOX.
IS-SNAKE DevKit Setup Manual 7. To use the IS-CTR-CAPTURE software, insert a USB cable into the CAPTURE TESTER USB port on the back panel of the IS-SNAKE-BOX. 8. Connect the DC plug of the AC Adapter to the DC connector (DC IN) on the rear panel of IS-SNAKE-BOX. 9. Plug the AC adapter into a standard 120 V AC wall socket. 5.9 Turning the Power On and Off Follow the procedure below to turn the power on. 1. Turn on the power switch on the rear of the IS-SNAKE-BOX. 2.
IS-SNAKE DevKit Setup Manual 3. If the power LED on the controller turns on and the LCD screen shows an image, the device can be used. Follow the procedure below to turn the power off. 1. Turn off the power switch on the rear of the IS-SNAKE-BOX. The controller will turn off automatically. This does not require any separate operation. 5.10 Activating the License After installing batteries for the first time or replacing them, use the following procedure to activate your license.
IS-SNAKE DevKit Setup Manual 6 Support 6.1 Website For information on IS-SNAKE DevKit and the latest version of IS-CTR SoftwarePackage, visit the following website. http://www.warioworld.com/ 6.2 Email Support Direct inquiries on IS-SNAKE DevKit to the following. INTELLIGENT SYSTEMS CO.,LTD. 10 Daimotsu-cho Kamitoba Minami-ku Kyoto-shi Kyoto-fu 601-8121 JAPAN TEL: +81-75-671-3100 FAX: +81-75-671-3105 E-mail: CTR_Support@intsys.co.
IS-SNAKE DevKit Setup Manual 7 FCC and Industry Canada Information In order to comply with FCC radio-frequency radiation exposure guidelines for an uncontrolled exposure, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada.
IS-SNAKE DevKit Setup Manual This radio transmitter IC: 5567A-FULLW001 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna type: 1/2 lambda type Gain: 2.
IS-SNAKE DevKit Setup Manual Revision History Version Revision Date Category 1.0 2014/08/07 — CTR-XX-XXXX-XXX-X Released: August 7, 2014 Description Initial version.
IS-SNAKE DevKit Setup Manual All company and product names in this document are the trademarks or registered trademarks of their respective companies. © 2014 Nintendo The contents of this document cannot be duplicated, copied, reprinted, transferred, distributed, or loaned, in whole or in part, without the prior approval of Nintendo.
