Operation Manual

10
5.2.4 ASI1
You can congure the settings of ASI1 in this menu.
ASI1 Source: Press the <ENTER> key and use the <UP> or <DOWN> key to roll up or down to select the signal
source of ASI output, there are 5 type of signal source optional:
CI De-encrypted:
1. the de-encrypted transport stream from CI functional block will be delivered to the ASI
output port on the back panel.
TUNER:2. the transport stream from Tuner block will be delivered to the ASI output port on the back panel.
ASI1 Input:3. the transport stream comes from ASI1 input port will be delivered to the ASI1 output port on
the back panel.
ASI2 Input:4. the transport stream comes from ASI2 input port will be delivered to the ASI2 output port on
the back panel.
Mux TS: 5. the transport stream comes from internal Mux functional block will be delivered to the ASI output
port on the back panel.
Note: The Mux TS is valid only when the Mux function block is enabled and turned on. Refer to section ‘Mux’
and section ‘Optional Function’ for how to set the Mux function block.
Press <ENTER> key to save or press <EXIT> key to scrap. A few seconds after the source being selected, the
TS will be delivered to the ASI output port on the back panel.
5.2.5 ASI2
The same conguration method like section of ‘ASI1’
5.2.6 SDI
You can congure the settings of SDI output in this menu.
Audio PID:
• press the <UP> <DOWN> keys to choose the audio PID from 1~4.
Embed Audios:
• there are 4 options: none, one&two, two, and one.
SDI Output Mode:
• congure output mode HD-SDI or SD-SDI
SDI H Offset:
• the range is 0~999
5.2.7 Mux
Note: this Mux menu is showed only when the Mux function block is enabled and turned on. And the Mux is
alternative (refer to section ‘Optional Function’ for how to turn on and set the Mux function block).
Mux Switch: • the internal multiplexer could be switched On/Off. The default value is ‘off’. To activate the
re-Multiplexing function, you should turn on this Mux functional block.
Bit Rate:• should be set to a specied value that doesn’t exceed the Maximum physical limit of the output
medium. For example, to deliver the multiplexed TS to an 8MHz DVB 256QAM modulator, it should not
exceed 55000Kb/s, otherwise overow occurs.
TS ID:• you can congure the TS ID to mark the multiplexed TS. Default value is 1.
Program List:• press the <ENTER> key to enter ‘Mux List’ sub-menu.
It shows all programs detected by IDLV-5000P. The programs could be come from ASI input, Tuner, TS/IP •
input or the internal CI de-encryption block. Use <UP> <DOWN> keys to roll up the program names, and
use <LEFT> <RIGHT> keys to switch among input sources, where a number in front of the program name
indicates the input source: 0-xxxxx displays the program name, which comes from ASI input.
1-xxxxx displays the program name, which comes from TUNER input.
2-xxxxx displays the program name, which comes from TS/IP input
3-xxxxx displays the program name which comes from the CI.
4-xxxxx displays the program name, which comes from ASI2 input.
5-xxxxx displays the program name, which comes from BISS De-encrypted
input.
On ‘Program List’ sub-menu, on the rst row, all encrypted programs are labeled with a ‘$’ sign.
All programs that are being selected to be re-multiplexed are labeled as ‘Pass’, otherwise, the un-selected
programs are labeled as ‘Fobrid’. Use <ENTER> key to selected or un-selected the program being shown.
When leaving the ‘Program List’ sub-menu, a new menu will be shown ‘Conrm changed?’ Press <ENTER> key
to validate all programs just be selected to be multiplexed or to scrap by pressing <EXIT> key.
After a few seconds, the multiplexed TS will be generated and delivered to the specied destination(s).