Installation Guide

ManualsBrandsIOTA ManualsCommercial Lighting10W Emergency LED Driver for Class 2 LED Luminaires. Constant Wattage Output. Universal 120-277V Input. Auto-Sense 10-60VDC Forward Voltage. Galvanized Steel Housing, 24 in. Flexible Conduit either side , Ni-Cad battery. UL Listed. CA Title 20.

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed, including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. CAUTION – To prevent electrical shock, do not mate unit connector until installation is complete and A.C.

power is supplied to the unit.

2. CAUTION – This ﬁxture provides more than one power supply output source. To reduce the risk of electrical

shock, disconnect both normal and emergency sources by turning off the A.C. branch circuit and by discon-

necting the unit connector.

3. CAUTION – This is a sealed unit. Components are not replaceable. Replace the entire unit when necessary.

4. CAUTION – Installation and servicing should be performed by qualiﬁed personnel only. De-energize before

opening.

5. The ILB is for use with grounded LED luminaires listed to UL standards. Not for use in heated air outlets or

hazerdous locations.

6. The ILB requires an unswitched A.C. power source of 120 to 277 volts, 50/60 Hz.

7. The ILB and A.C. driver must be on the same branch circuit.

8. Do not mount near gas or electric heaters.

9. The ILB should be mounted in locations and at heights where it will not readily be subjected to tampering by

unauthorized personnel.

10. The ILB will supply 10-60 VDC output at the individual rated speciﬁcation for 90 minutes. See individual units

for output speciﬁcations.

11. Suitable for use in damp locations and plenum spaces.

12. Suitable for Luminaires, recessed Type IC (intended for insulation contact).

13. For use in 0° C minimum, 55° C maximum ambient temperatures.

14. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition, void

warranty, and result in non-compliance with UL speciﬁcations.

15. Do not use this equipment for other than intended use.

16. Install in accordance with the National Electrical Code and local regulations.

17. Lighting ﬁxture manufacturers, electricians, and end-users need to ensure product system compatibility before

ﬁnal installation. See addendum for compatibility and covered luminaire requirements.

ILB-CP

‘A’ MOUNTING DESIGN

EMERGENCY LIGHTING EQUIPMENT

FOR LED

INSTRUCTION MANUAL

P.O. BOX 11846 TUCSON, AZ 85734

(520) 294-3292 • FAX (520) 741-2837

www.iotaengineering.com

SAVE THESE INSTRUCTIONS

Patented. See iotaengineering.com/patents for more details

EMERGENCY LED DRIVER FOR USE

WITH LED LUMINAIRES IDENTIFIED IN

THE MANUFACTURER’S INSTALLATION

INSTRUCTIONS

E473237

CLASS 2 OUTPUT

Summary of content (5 pages)

PAGE 1
ILB-CP ‘A’ MOUNTING DESIGN EMERGENCY LIGHTING EQUIPMENT FOR LED P.O. BOX 11846 TUCSON, AZ 85734 (520) 294-3292 • FAX (520) 741-2837 www.iotaengineering.com Patented. See iotaengineering.com/patents for more details INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1.
PAGE 2
INSTALLATION INSTRUCTIONS CAUTION: Before installing, make certain the A.C. power is off and the ILB unit connector is disconnected. 1. FIXTURE The ILB-CP can be used with most LED loads that operate at 10-60 VDC. See the ILB Model Specification Chart for output specifications of the unit being installed. 1. The ILB-CP series has been evaluated to and found compliant to UL standard 924. The as-installed performance of system must meet or exceed all Federal, State, and Local code requirements. 2.
PAGE 3
ILB-CP WITH TBTS TEST ACCESSORY Illustration 2: Typical Wiring Diagram SWITCHED OR UNSWITCHED HOT AC INPUT (120 TO 277V) WHITE AC (NORMAL) DRIVER LED OUTPUT (-) LED INPUT(+) LED OUTPUT (+) LED INPUT (-) LED LOAD COMMON WHT/BLK RED (+) WHT/BLK WHITE WHT/RED BLK/ORG (120 TO 277V, 50/60HZ) TBTS TEST ACCESSORY WHT RED RED OR RED/BLK (+) UNSWITCHED 24/7 POWER IOTA ILB-CP EMERGENCY DRIVER BLUE (-) RED/WHT (+) BLUE/WHT (-) UNIT CONNECTOR ATTENTION: DO NOT MATE UNIT CONNECTOR UNTIL INSTALLATIO
PAGE 4
TESTING & MAINTENANCE Pressing the TBTS turns off the light on the TBTS and forces the unit into emergency mode, interrupting power to the designated A.C. driver. The LED load is now being lit by the ILB unit. After releasing the TBTS, the fixture returns to normal operation after a momentary delay. To simulate a “BLACK OUT” use the circuit breaker to turn off A.C. power. Initial Testing – Allow the unit to charge approximately 1 hour, then conduct a short discharge test.
PAGE 5
CP Series Compatibility and Suitability of Use Guidelines Addendum (Rev.11042014) The purpose of this addendum is to sufficiently identify electrical compatibility and predictable emergency light output of the LED luminaire when used with the IOTA ILB-CP Series LED emergency drivers. Verification of these operating traits does not constitute a code-compliant, as-installed emergency egress system.