Manual

ManualsBrandsJ&M ManualsHardwareJD-STS series

Combine Grain Tank Set-Up Instructions

for John Deere STS Series Combines

Lanyards and

Lynch Pins

shown below

are typical on

Front, Rear

and Side

Panels

Fold this Panel First

Remove Knock-outs to

install Sensor Mounting

Bracket. When installing

Tip-Up Panels, DO NOT

remove knock-outs.

Sensor Mounting Bracket

will be installed on Tip-Up

Panel.

Remove Knock-outs and locate GPS Bracket here.

Remove Knock-out and relocate existing light here.

Assembly Instructions

For STS Models 9560, 9660 or 9760 Series Combines with 16”

auger, install additional tank brace before Step 1 (see insert).

Step 1:

Attach both rear braces to combine hopper using (8) 3/8” x 1” Flange

Bolts and (8) 3/8” Flange Nuts.

Position the rear brace on top of the rear C-Channels of the combine

and drill 3/8” holes in the combine hopper to attach these braces.

NOTE: C-Channels are located under door hatch close to grain tank

(door hatch may need to be slid back to install braces)

Step 2:

Place frame halves on combine hopper. Loosely fasten frame halves

to existing brackets of combine hopper using (4) 5/16” x 1 1/2” Bolts,

(8) 3/8” Heavy Washers and (4) 5/16” Flange Nuts. To prevent grain

leakage, slide the Frame Shim between the frame and the tank to

ensure a tight seal. For STS Models with 18” auger, place the four

Clamp Plates below the hinges of the frame. Loosely secure the frame

(and frame shim) either to the hinge or the adjacent tank bracket using

5/16” x 5/8” Flange Bolts and Flange Nuts. Do not tighten Clamp

Plates to hinge as they may need repositioned to ensure a proper fit.

# Part # Description Qty

1 STS-CP Corner Panel 4

2 STS-FRSP Front/Rear/Side Panel 4

3 STS-FRF Front/Rear/Frame 2

4 STS-TRL Tubing Rail (Left with cut-out) 1

4 STS-TRR Tubing Rail (Right) 1

5 STS-RB Rear Brace 2

6 JD-SMB Sensor Mounting Bracket 1

7 CTE-PP Plastic Plug 8

8 CTE-PL Plastic Lanyard 24

9 CTE-LP Lynch Pin 24

10 JD-EW Extension Wire 1

11 FB-516112 5/16" x 1 1/2" Flange Bolt 4

12 HB-384 3/8" x 4" Bolt 8

13 HB-38412 3/8" x 4 1/2" Bolt 8

14 6MM-475 6MM x 4 3/4" (8.8) 8

15 FB-381 3/8" x 1" Flange Bolt 10

16 FB-51658 5/16" x 5/8" Flange Bolt 26

17 FN-516 5/16" Flange Nut 30

18 LN-38 3/8" Lock Nut 8

19 6MM-NLN 6MM Nylon Lock Nut 8

20 HW-38 3/8" Heavy Washer 8

21 CTE-HRW Hand Rail Weldment 1

22 DS-14112 1/4" x 1 1/2" Drill Screw 1

23 IW-71212 Inspection Window 4

24 62095-7 Window Molding 4

25 FN-38 3/8" Flange Nut 20

26 GPS-RB1 GPS Bracket 1

27 GPS-RB2 GPS Bracket Adapter 1

28 STS-TB1 Tank Brace Support 1

29 CTE-SS1 Step 1

30 STS-CP18 Clamp Plate (combines w/18" auger) 4

31 STS-FS1 Frame Shim 2

NOTE: The Rear Braces are not

needed for 2006 and newer 9660,

9760 or 9860 STS Model combines.

Summary of content (3 pages)

PAGE 1
Combine Grain Tank Set-Up Instructions Lanyards and Lynch Pins shown below are typical on Front, Rear and Side Panels for John Deere STS Series Combines Remove Knock-outs and locate GPS Bracket here. Remove Knock-out and relocate existing light here. Remove Knock-outs to install Sensor Mounting Bracket. When installing Tip-Up Panels, DO NOT remove knock-outs. Sensor Mounting Bracket will be installed on Tip-Up Panel.
PAGE 2
Combine Grain Tank Set-Up Instructions (Continued) for John Deere STS Series Combines Assembly Instructions (Continued) Step 3: Fasten Tubing Rails (Note: Left Side Tubeing Rail has cut-outs on underside of tube) to frame halves using (4) 3/8” x 4” Bolts and (4) 3/8” Lock Nuts. Step 4: Center frame on combine hopper. Securely tighten the 5/16” x 1 1/2” bolts installed earlier. For STS models with 18” auger, secure the 5/16” x 5/8” Flange Bolts and Flange Nuts used on the Clamp Plates.
PAGE 3
Combine Grain Tank Set-Up Instructions for John Deere STS Series Combines IMPORTANT! For STS Models 9560, 9660 or 9760 Series Combines with 16” auger, install additional tank brace before extensions. STS Models equipped with the large capacity auger system do not require the additional tank brace.