Installation Manual

14
STYLE 1SHUTOFF VALVE CONNECTION
NOTE : If your water line connection does not look like
Style 1, see “Style 2—Copper Line Connection.”
1. Unplug refrigerator or disconnect power supply.
IMPORTANT :
 There is not enough clearance to achieve a flush
installation if a water shutoff valve is located in the
wall behind the refrigerator. The water shutoff should
be located in the base cabinet on either side of the
refrigerator.
 Before attaching the tubing to shutoff valve, flush
the main water supply line to remove particles and
air in the water line. Allow enough flow so that water
becomes clear. Flushing the water line may help
avoid filters and/or water valves from becoming
clogged.
2. Connect the flexible, codes-approved water supply
line to the water shutoff valve by threading the
provided nut onto the shutoff valve as shown.
3. Place the end of the tubing into a bucket, and turn
shutoff valve ON.
4. Check for leaks. Tighten any nuts or connections
(including connections at the valve) that leak.
STYLE 2COPPER LINE CONNECTION
NOTE : If there is a water supply line that meets the
specifications in “Water Supply Requirements,” proceed
to “Connecting to Refrigerator.” If not, use the following
instructions to connect to the household cold water
supply.
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet
long enough to clear line of water.
3. Locate a 1/2" to 1⁄" (1.3 cm to 3.18 cm) vertical cold
water pipe near the refrigerator.
IMPORTANT :
 Make sure it is a cold water pipe.
 Horizontal pipe will work, but drill on the top
side of the pipe, not the bottom. This will help
keep water away from the drill and keep normal
sediment from collecting in the valve.
4. Determine the length of copper tubing you need.
Measure from the connection on the refrigerator to
the water pipe. Add 7 ft (2.1 m) to allow for cleaning.
Use 1/4" (6.35 mm) O.D. (outside diameter) copper
tubing. Be sure both ends of copper tubing are cut
square.
5. Using a cordless drill, drill a 1/4" (6.35 mm) hole in the
cold water pipe you have selected.
6. Fasten the shutoff valve to the cold water pipe with
the pipe clamp. Be sure the outlet end is solidly in
the 1/4" (6.35 mm) drilled hole in the water pipe and
that the washer is under the pipe clamp. Tighten the
packing nut. Tighten the pipe clamp screws slowly
and evenly so washer makes a watertight seal. Do not
overtighten.
IMPORTANT : Before attaching the tubing to shutoff
valve, flush the main water supply line to remove particles
and air in the water line. Allow enough flow so that water
becomes clear. Flushing the water line may help avoid
filters and/or water valves from becoming clogged.
7. Slip the compression sleeve and compression nut
on the copper tubing as shown. Insert the end of
the tubing into the outlet end squarely as far as it
will go. Screw compression nut onto outlet end with
adjustable wrench. Do not overtighten the clamp or
the sleeve. This will crush the copper tubing.
8. Turn off the shutoff valve on the water pipe. Coil the
copper tubing.
9. Connect the flexible, codes-approved water supply
line to the water shutoff valve by threading the
provided nut onto the shutoff valve.
10. Place the end of the tubing into a bucket, and turn
shutoff valve ON.
11. Check for leaks around the saddle valve. Tighten any
nuts or connections (including connections at the
valve) that leak.
A
B
C
A. Bulb
B. Nut
C. Water tubing
A
B
C
D
EF
G
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
E. Compression sleeve
F. Shutoff valve
G. Packing nut