Installation Manual
Table Of Contents
- Introduction
- VARIANTS AND ACCESSORIES
- INSTALLATION REQUIREMENTS
- INSTALLATION INSTRUCTIONS
- Introduction
- VARIANTES ET ACCESSOIRES
- EXIGENCES D’INSTALLATION
- Outils et pièces
- Dimensions du produit
- Dimensions pour l’ouverture des portes
- Préparation du site
- Exigences d’emplacement
- Spécifications de l’alimentation en eau
- Spécifications électriques
- Exigences d’installation de l’ensemble de panneaux en acier inoxydable
- Exigences d’installation et dimensions des panneaux de bois personnalisés
- INSTRUCTIONS D’INSTALLATION
- Déballage du réfrigérateur
- Déplacement du réfrigérateur dans le domicile
- Raccordement à la canalisation d’eau
- Brancher le réfrigérateur
- Installation des garnitures latérales
- Déplacement du réfrigérateur à son emplacement définitif
- Réglage de l’aplomb et alignement du réfrigérateur
- Installation de la grille de la base
- Terminer l’installation
17
After the refrigerator is leveled and aligned, remove
the installation block from the door hinge and use
it to check the spacing between the panels and
adjacent cabinets.
NOTE : The installation block is designed to provide
accurate spacing for 3/4" (1.9 cm), 3/8" (9.53 mm) and
1/8" (3.18 mm).
1. Place top of cardboard carton or plywood under
refrigerator. Remove dolly.
2. Move the refrigerator straight back and evenly into
the opening. Be sure that the water tubing is not
kinked and the power supply cord is on top of the
refrigerator.
NOTE : If the power supply cord is behind the
refrigerator, it will not install properly.
3. Make sure the installation block is flush with the
adjacent cabinets.
NOTE : To achieve a flush installation, it is critical to
verify a 3/4" (1.9 cm) depth from the front face of the
adjacent cabinetry to the refrigerator.
LEVEL AND ALIGN REFRIGERATOR
IMPORTANT : All four leveling legs must contact the floor
to support and stabilize the full weight of refrigerator.
Rollers are for moving the refrigerator, not for permanent
support.
After moving the refrigerator to its final location:
1. Use a 5/16" socket driver to turn the leveling bolts
clockwise to extend the legs to the floor as shown.
The rollers should be off the floor.
2. Adjust the leveling legs to level and align the
refrigerator from left to right and front to back so that
the refrigerator is level and aligned with the cabinets.
3. Continue adjusting the leveling legs until the top of
the refrigerator is making contact with the bottom of
the solid soffit, or the bottom of the anti-tip boards, if
anti-tip boards were used. Do not crush the
compressor cover.
3/4"
(1.9 cm)
3/8"
(9.53 mm)
1/8"
(3.18 mm)
A
B
C
A. Adjacent cabinet or wall
B. Installation block
C. Face of refrigerator
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is
completely installed.
Use two or more people to move and install
refrigerator.
Failure to do so can result in death or serious injury.
A B
A
B
A. Rear leveling bolt
B. Front leveling bolt
2" (5 cm)
84"
(213.4 cm)
A
B
C
D
A. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards
B. Attach to studs with six #8 x 3" (7.6 cm) screws
C. Compressor cover
D. Distance from bottom of anti-tip board to floor
3/4" (1.9 cm)