Installation guide

ManualsBrandsJenn-Air ManualsCooktopOfficial Jenn-Air 30" electric downdraft cooktop

Electric Convertible CooktopI : JENN-AIR 1

Models JED8130, JED8230 & JED8345 _ WESTFOURTHSTREET, NORTH" NEWTON, IA50208

DIMENSIONS SHOWN IN BOTH INCHES AND CENTIMETERS

*Blowermay be rotated forhorizontalorverticaldirectionby looseningnuts aroundblowerinlet.Accessibleinsideventilation

chamber.

TIE DOWN BOLT

ON EACH

:'ASE

CONTAINER

• NOTICE TO INSTALLER: Leave these instructions

withthe appliance.

• NOTICE TO CONSUMER: Retain these instructions

for future reference.

23.8t cm

MODEL SERIES: JED8345 TRIPLE BAY

Typ. for Container Supplied,

6 1/4" (1,5,88 cm) is required for removal.

13 t5/]6"

35. I ¢m

CONTAINER

2 718 ° _ '

7,3 crn

"_= "=,_ 2 7/8"

68.0 cm 7.3 cm

34.9 o"a 30.0 cm

ONLY MODELS WITH GRILLING FEATURE HA VE BEEN ILLUSTRATED

INSTRUCTIONSTO INSTALLER,

• Dimension "B" - Provide 2" min. (5.08 cm) cabinet clearance to motor for cooling purpose,

• Installer - Where possible, 6" (15.24 cm) is recommended for motor/blower service.

• Side Clearance - Grill models installed near a side wall must allow a minimum clearance of 6" (15,24 cm) for

maximum performance.

° Electrical Hook UP - The unit should be properly circuit protected and wired according to local electrical codes. See

electrical wiring information on back, Unit power requirements are located on the data plate.

• ** Access must be provided to remove and empty grease container(s).

8101 P421 ..60

(10-01-oo)

A INCHES CM

Double Bay 29 + 1/16" 73.66

TriPle Bay 43 1/4 + 1/i6 109.86 + 116

MODEL SERIES: JED8130 & JED8230 DOUBLE BAY

_EASE

Summary of content (9 pages)

PAGE 1
Electric Convertible :FOURTH JENN-AIR 1 Models JED8130, JED8230 Cooktop & JED8345 I _ WEST STREET, NORTH" NEWTON, IA50208 DIMENSIONS SHOWN IN BOTH INCHES AND CENTIMETERS *Blower may be rotated for horizontalor verticaldirectionby looseningnuts aroundblower inlet. Accessible insideventilation chamber. • NOTICE TO INSTALLER: Leave these instructions with the appliance. TIE DOWN BOLT ON EACH • NOTICE TO CONSUMER: Retain these instructions for future reference. :'ASE CONTAINER 23.
PAGE 2
Installing Cabinetry Over Your Jenn-Air Grill Electrical Wiring Information A* = 30" (76.2 cm) minimum clearance between the top of the cookingplatformand the bottomof an unprotected wood or metal cabinet. The neutralof this unitis groundedto the frame through the green grounding wire. If local conditions do not permit grounding of theneutral, untwist or disconnect the green wire and connect the green wire to ground in accordance with local codes. Connect the white neutral to the service neutral.
PAGE 3
240 EdwardsStreet, SE Cleve!an&Tennessee37311 Tel: 423-472-3333 Fax:423-478-6710 4. FREE-STANDING CUTOUT - 30 I/8"(76.52cm) minimum clearance isrequired. - Carefully mark thecountertop,recheckyourdimensions andmake thecutout. - NOTE: Range sidepanelsmay be desirable ifthecutout istoolargeorcabinets areon oneside of therangeonly. MEASURE FOR SLIDE-IN CUTOUT - Most standard counters are 25 _ (63.50 cm) deep, 36" (91.44 era) high, and extend I" (2.54 cm) over the cabinet front.
PAGE 4
2.40EdwardsStreet,SE Cevetand.Tennessee3721l Te,l: 422-472-3333 Fax:423-478-5710 7. SLIDE-IN CUTOUT - Check your marked-up dimensions carefully.The reardimensionsshown intheillustration must be maintained. - NOTE: Where thisisnot done, itwillbe necessaryto relieve a portionof theundersideof the countertopand/or supportmembers toclearthe range mar panel. - Cuttingtoleranceis 4- 1/16" (.16cm). - Carefully mark the cutout. _mt TOt= "-., {443 cm) . 9.
PAGE 5
C_.stomer SeP:ic_ Z40 EawardsSLreet,SE C1eve!and, Tennessee 37311 Tei: _22-472-3333 Fax:_23-478-6710 I0. FLOOR VENT CUTOUT (JOISTS AS SHOWN) - Check the direction of the floor joists (see illustration), tf the joists' direction is as shown, locate the cutout on the '7" as illustrated. The cutout must miss the floarjoists! - Cutout may be moved from side to side on line to clear floor joist. - Recheck your dimensions and make the cutout. 11.
PAGE 6
2J-gEawa_dsStreeL SE C;eveiand,Tennessee37311 Tel:423-477.-;333 Fax:'_23-J-78-67! 0 13. INSTALL BLOWER (PRIOR TO INSTALLING RANGE) - Refer to your vent plan. It may be desirable to attach part of the ducting to the blower before it is installed. - Position the blower (see illustration) and attach it to the floor with at least two (2) screws. - Apply duct tape around blower exhaust/duct joint. THROUGH THROUGH OUTSIDE WALl. THE FLOOR r It rfZfTflVfl_l/ .---. ff¢ j METAL ffJ'--J_ .." E.
PAGE 7
Custcmef Serwc8 240EdwardsStreet SE Ceveiand.Ten_esse_37211 T_: 473-472-2223 Fax:_23-478-87t0 16. CONNECT ELECTRICAL (FOUR CONDUCTOR WIRE) - CAUTION: Make sure power to cable is OFF. - Remove the range electrical service cover located on the back, lower left-hand corner. Remove the ground strap,,screw and bend the strap up as shown. - Install a 3/4 (1.19 cm) cable clamp in the hole provided, below the terminal block. - Strip 3_ (7.62 cm) of outer insulation from the cable. - Strip 1/2" (1.
PAGE 8
Cus[ome r _ePdc_ 2_0EdwardsStreet, SE Ceveian_.Tennessee373I I Te!: a22-'72-3333 t9. ANTI-TIP BRACKET INSTALLATION - With the unit installed in the final location, establish left side and back of the unit. - Locate left bracket 5/8" (1.58 cm) in from the left of the unit. - Locate the right bracket 27 718" (70.80 cm) to the right of the left bracket. - Locate the rear of both brackets flush to the back of the unit if a backsplash is not used.
PAGE 9
24(3EdwardsStree[.SE C[eveiane.Tennessee3731'[ Tel:423-472_-3333 Fax:_23-47_,.,_710 22. INSTALL FLEX DUCT - Attach the flex duct to the blower and range (See illustration). duct clamp at each connection, Using a screwdriver, securely tighten 23. CHECK OPERATION - Unpack and install grill element in one side and cooking cartridge in other side, - Be sure to remove all packaging materials from unit prior to applying power. - Switch the electrical circuit breaker to the ON position.