Service This manual is to be used by qualified appliance technicians only. Maytag does not assume any responsibility for property damage or personal injury for improper service procedures done by an unqualified person.
Important Information Maytag will not be responsible for personal injury or property damage from improper service procedures. Pride and workmanship go into every product to provide our customers with quality products. It is possible, however, that during its lifetime a product may require service.
Table of Contents Important Information ................................................... 2 Important Safety Information What to Do if You Smell Gas ................................... 4 Oven Fires ............................................................... 4 Safety Practices for Servicer .................................. 4 Servicing .................................................................. 4 Receiving Oven ........................................................ 5 Using the Oven ...........
Important Safety Information As with all appliances, there are certain rules to follow for safe operation. Verify everyone who operates oven is familiar with the operations and with these precautions. Use appliance only for its intended purpose as described. Pay close attention to the safety sections of this manual. Recognize the safety section by looking for the symbol or the word safety. Recognize this symbol as a safety precaution.
Important Safety Information 3. Checking for gas leaks—Never check for leaks with any kind of open flame. Soap and water solution should be used for this purpose. Apply solution to suspected area and watch for air bubbles which indicates a leak. Correct leaks by tightening fittings, screws, connections, applying approved compound, or installing new parts. 4. Using lights—Use a hand flashlight when servicing ranges or checking for gas leaks. Electric switches should not be operated where leaks are suspected.
Important Safety Information ! Regulator must be set for the type of gas being used Natural or LP. After servicing regulator, make certain it is set properly before completing service. CAUTION Do not store items of interest to children in cabinets above range. Children may climb on oven to reach these items and become seriously injured. Baking, Broiling, and Roasting Gas Burner Orifices • Do not use oven area for storage. • Stand back from range when opening door of a hot oven.
General Information This manual provides basic instructions and suggestions for handling, installing and servicing gas ranges. The directions, information, and warnings in this manual are developed from experience with, and careful testing of the product. If the unit is installed according to this manual, it will operate properly and will require minimal servicing. A unit in proper operating order ensures the consumer all the benefits provided by clean, modern gas cooking.
General Information Specifications Model Identification Refer to individual Technical Sheet for specification information. All air vents must be kept clear during cooking. If air vents are covered during operation, the oven may overheat. If this occurs, a sensitive, thermal safety device automatically removes power to the oven, rendering the oven inoperable. The oven will remain in this state until it has sufficiently cooled. Complete enclosed registration card and promptly return.
General Information Grounding NOTE: This appliance must be properly grounded, for personal safety. Power cord on this appliance is equipped with a threeprong grounding plug. This matches standard threeprong grounding wall receptacle to prevent possibility of electric shock from this appliance. Consumer should have wall receptacle and circuit checked by qualified electrician to verify receptacle is properly grounded.
Range Description Shut-off Valve/ Pressure Regulator (Backside of Range) Top Surface Burners and Grates Burner Control Valves Burner Control Valves Electronic Control and Touchpad Oven Cavity Bake Burner Broil Burner Convection Fan and Element Storage or Warming Drawer Rating Label Model Number 10 16026923 © 2006 Maytag Services
Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury, or death, disconnect power and gas to range before servicing, unless testing requires power and/or gas. Troubleshooting Chart Problem Burners will not ignite; no spark at top burner. Burner will not ignite. No spark to burner ignitors when burner knob is rotated to "LITE" position. No spark or only random spark at one ignitor. Unit continues to spark after knob is turned to OFF position.
Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury, or death, disconnect power and gas to range before servicing, unless testing requires power and/or gas. Problem Gas flows to bake/broil burner, but burner does not light. Broil burner shuts off shortly after the start of self-clean operation. Bake and broil functions operate normally. Fan motor does not operate. Oven smokes/odor first few times of usage. Failure Codes. Oven not operating.
Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury, or death, disconnect power and gas to range before servicing, unless testing requires power and/or gas.
Troubleshooting Procedures ! WARNING To avoid risk of electrical shock, personal injury, or death, disconnect power and gas to range before servicing, unless testing requires power and/or gas.
Testing Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing, unless testing requires power and/or gas. Component Testing Procedures Illustration Component Oven light & housing Test Procedure Results Verify bulb is properly inserted. Disconnect connector and test resistance of terminals ............................. Continuity with bulb inserted. Measure voltage at oven light...................
Testing Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing, unless testing requires power and/or gas. Illustration Component Convection motor, single speed Test Procedure Results Measure voltage ...................................... 120 VAC. Check motor windings to ground.............. No continuity. RPM: ............
Testing Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing, unless testing requires power and/or gas. Illustration Component Orifice holder, dual ring burner 12 K btu 3 K btu Dual ring burner valve Test Procedure Results Verify gas pressure................................... 5" Natural. 10" LP/propane. Check orifice for debris............................. Clean as needed. Verify gas is supplied............................
Testing Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing, unless testing requires power and/or gas. Control Component Switch membrane assembly NOTE: To avoid equipment damage, use caution when checking electronic control circuitry.
Testing Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing, unless testing requires power and/or gas.
Testing Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing, unless testing requires power and/or gas. Feature Tone Options Determines cook tones, timer tones and volume settings. 12-Hour Shutoff Disables 12-hour shutoff, allowing the oven to operate indefinitely. Cook Tones Determines the number and duration of cook time reminder chimes.
Testing Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing, unless testing requires power and/or gas. Relay Logic for EOC III NOTE: Subsequent changes implemented after the release of this technical sheet may have altered the parameters identified in this chart.
Testing Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing, unless testing requires power and/or gas. "Quick Test" Mode for EOC III Follow the procedure below to perform the EOC III quick test. Once the control is in the quick test mode, any relay may be activated in any sequence. The test mode will be exited after 10 minutes of inactivity (no pads pressed within 10 minutes). 1. 2. 3. 4. 5. 6. 7.
Testing Procedures ! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power and gas to range before servicing, unless testing requires power and/or gas.
Disassembly Procedures To avoid risk of electrical shock, personal injury or death; disconnect power and gas before servicing, unless testing requires power and/or gas. Removing and Replacing Range Maintop Assembly Removal (Select Models) 1. 2. 3. 4. 1. Remove power from unit. 2. Remove range from installation position, see “Removing and Replacing Range” procedure. 3. Remove front side trim, see "Front Side Trim Removal" procedure. 4.
Disassembly Procedures To avoid risk of electrical shock, personal injury or death; disconnect power and gas before servicing, unless testing requires power and/or gas. Spark Module Replacement Burner Switch Replacement 1. Remove unit from installation position, see “Removing and Replacing Range” procedure. 2. Remove screws securing rear access panel. 3. Disconnect and label wire connections from the spark module. 4. Remove screws securing spark module to unit chassis. 5.
Disassembly Procedures To avoid risk of electrical shock, personal injury or death; disconnect power and gas before servicing, unless testing requires power and/or gas. Cooling Fan Replacement 1. Remove power from unit. 2. Remove range from installation position, see "Removing and Replacing Range" procedure. 3. Remove back panel, see "Back Panel Removal" procedure. 4. Label and disconnect wire terminals from cooling fan. 5. Remove screws securing fan to range chassis. 6.
Disassembly Procedures To avoid risk of electrical shock, personal injury or death; disconnect power and gas before servicing, unless testing requires power and/or gas. 7. Remove screw securing light socket to oven cavity. 8. Label and disconnect wire terminals from light socket. 9. Reverse procedure to reinstall light socket. Regulator Removal 1. Disconnect power before servicing. 2. Remove range from installation position, see "Removing and Replacing Range" procedure. 3. Disconnect tubing from regulator.
Disassembly Procedures To avoid risk of electrical shock, personal injury or death; disconnect power and gas before servicing, unless testing requires power and/or gas. Oven Door Latch Replacement 1. Remove control panel, see "Control Panel Removal" procedure. 2. Remove screws securing door latch to the front of the oven cavity outer shell. 3. Slide oven door latch assembly forward to diagnose. 4. Label and disconnect wire terminals from latch assembly. 5.
Disassembly Procedures To avoid risk of electrical shock, personal injury or death; disconnect power and gas before servicing, unless testing requires power and/or gas. Warming Drawer Hi-Limit Switch Replacement (Select Models) Warming Drawer Disassembly 1. Remove unit from installation position, see “Removing and Replacing Range” procedure. 2. Remove front side trim, see "Front Side Trim Removal" procedure. 3. Remove warming drawer, see "Warming Drawer Removal (Select Models)" procedure. 4.
Disassembly Procedures To avoid risk of electrical shock, personal injury or death; disconnect power and gas before servicing, unless testing requires power and/or gas.
Appendix A The Installation information provided in this service manual is representative of a limited number of models. Reference the customer’s Installation literature included with the product, order a copy (if needed), or consult Jenn-Air’s website for the specific model. www.jennair.
Installation Instructions Jenn-Air Updraft Gas Slide-In Range Cuisinière à gaz encastrable à circulation ascendante Jenn-Air/ Estufa deslizante a gas de corriente ascendente Jenn-Air Installation Instructions/Instructions d’installation/Instrucciones de Instalación INSTALLER: Leave these instructions with the appliance./INSTALLATEUR : Laissez ces instructions avec l’appareil./ INSTALADOR: Deje estas instrucciones con el electrodoméstico.
Installation Instructions Jenn-Air Updraft Gas Slide-In Range INSTALLATION INSTRUCTIONS PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE This manual is intended to assist in the initial installation and adjustments of the range. • Only qualified personnel should install or service this range. • Read “Safety Instructions” in Use & Care book before using range. • Improper installation, adjustment, alteration, service, maintenance or use of range can result in serious injury or property damage.
Installation Instructions CONNECTING THE RANGE (cont) Gas Supply Installation of this range must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1latest edition. In Canada the range must be installed in accordance with the current CGA Standard CAN/CGA-B149 - Installation Codes for Gas Burning Appliances and Equipment and/or local codes.
Installation Instructions IMPORTANT: Keep for Local Inspector/IMPORTANT : À conserver pour l’inspecteur local/ IMPORTANTE: Guarde esta información para el inspector local. Com Wa busti ll C ble Arm abine cuis oires d ts/ mat ine en e é com riaux bu Arm stibles / comarios d bus e pa tible red Profondeur max., des armoires audessus de l’appareil : 33 cm (13 po) (7 3 .6 ” cm ) ” 30cm) 1 (333” cm ) .2 (76 ” 18cm) (7 3 .6 ” cm ) 13" (33 cm) Max. Depth of cabinets above cooktop 2 (63 5” .
Installation Instructions IMPORTANT: Keep for Local Inspector (cont)/IMPORTANT : À conserver pour l’inspecteur local (suite)/ IMPORTANTE: Guarde esta información para el inspector local (cont.) DÉGAGEMENTS La cuisinière peut être installée avec un dégagement nul contre des matériaux combustibles à l’arrière et sur les côtés en dessous de la table de cuisson.
Installation Instructions Dimensions/Dimensions/Dimensiones 25 ” If end cabinet is not present, side panel kit UXA1100AA (B= black, W= white, S= Stainless) may be ordered from dealer. . 3 23 ( .2 5” (63 If cabinet backsplash behind unit is not present, kit UXA9107AA (B= black, S=stainless, W= white) may be ordered from dealer. ) 5cm 59. (76 0” .2c m) m) 1c ) a su NOTE: For counter tops with formed front edge, shave raised section to clear top.
Installation Instructions B C A e Use & Car Guide D n Installatio ns Instructio Included./Compris./Se incluye. 5/16" Not Included./Non inclus./No se incluye. Tools Needed./Outils nécessaires./ Herramientas Necesarias. If you have LP (propane) it is recommended to initiate the conversion prior to installation. The conversion instruction kit can be found on the regulator shelf behind the shield./ Avec le GPL, il est recommandé de faire la conversion avant l'installation.
Installation Instructions 4 3 TURN OFF GAS SUPPLY TO PRODUCT. 1 COUPEZ L'ALIMENTATION EN GAZ DE L'APPAREIL. 2 5 Regulator/ Détendeur/ Regulador 3 CIERRE EL SUMINISTRO DE GAS AL PRODUCTO. Apply pipe thread compound approved for LP gas to all threads. Always hold the regulator in stable position while attaching gas supply line./Appliquez sur tous les filetages un composé à joints approuvé pour le GPL.
Installation Instructions 9 10 Insert plug into grounded outlet./Insérez la fiche dans la prise mise à la terre./Conecte el enchufe en un tomacorriente puesto a tierra. Slide range into position. Installer, take caution not to damage floor. Do not tilt range side-to-side; may damage end trim./ Introduisez la cuisinière en place. Installateur : N'endommagez pas le sol. N'inclinez pas la cuisinière sur un côté, au risque d'endommager la garniture./ Deslice la estufa a su lugar definitivo.
Appendix B The Use and Care information provided in this service manual is representative of a limited number of models. Reference the customer’s Use and Care literature included with the product, order a copy (if needed), or consult Jenn-Air’s website for the specific model. www.jennair.
Use & Care JENN-AIR GAS DOWNDRAFT SLIDE-IN RANGE ® USE & CARE GUIDE ® B–2 16026923 © 2006 Maytag Services
Use & Care SURFACE COOKING High: Use to bring liquid to a boil, or reach pressure in a pressure cooker. Always reduce setting to a lower heat when liquids begin to boil or foods begin to cook. Low: Use to simmer foods, keep foods warm and melt chocolate or butter. Some cooking may take place on the Low setting if the pan is covered. It is possible to reduce the heat by rotating the knob toward OFF. Be sure flame is stable. An intermediate flame size is used to continue cooking.
Use & Care Burner Grates Cooktop To prevent the cooktop from discoloring or staining: • Clean cooktop after each use. • Wipe acidic or sugary spills as soon as the cooktop has The grates must be properly positioned before cooking. When installing the grates, place the tab ends toward the center, matching the straight bars. Improper installation of the grates may result in chipping of the cooktop. cooled as these spills may discolor the porcelain.
Use & Care Ventilation System The built-in ventilation system removes cooking vapors, odors and smoke from foods prepared on your cooktop and grill. • To operate the ventilation system manually, push the Vent Fan pad located on the electronic control. Push once for Low, push again for High and a third time to turn the fan Off. ➞ • The ventilation system will operate automatically when the grill element is in use.
Use & Care OVEN COOKING Control Panel AB CD E I J KL F M G N O H P The control panel is designed for ease in programming. The display window shows options for each function and moves from step to step through the programming process. Control panel features vary by model. Oven display above is programmed for a bake operation. If you need to back out of a function or option in the display, press the Back pad.
Use & Care Activating and canceling the clock/day of week display: 3. Press the number pads to enter the new desired time. 1. Press Setup pad. Canceling the Timer: 4. Press Enter pad. 2. Select CLOCK. 1. Press the TIMER 1 or TIMER 2 pad twice. 3. Press the arrow to scroll until DISABLE is displayed. If both Timers are active: 4. Select DISABLE. 5. Select TIME. 6. Select OFF to turn the clock display off, or select ON to turn the clock display on. 7.
Use & Care Baking heat at the selected time and cooks for the specified length of time. When that time has elapsed, the oven will keep the food warm for up to an hour then automatically turn off. To set Bake: 1. Press the Bake pad. 2. Select the oven temperature using the Quickset pads. To set Cook & Hold: OR 1. After Bake has been programmed, press the More Options pad. Enter the desired temperature using the number pads. Press Enter pad to set. 2. Select COOK/HLD.
Use & Care 3. Select CNVT ROAST using the Quickset pads. Notes: • The oven control comes from the factory set for Auto Convect Conversion. When using Convect Bake enter the conventional baking temperature. The control automatically converts the temperature to 25° less than the conventional temperature. 4. Select the oven temperature using the Quickset pads. • When using Convect Roast the temperature will not be automatically reduced. Enter the conventional roasting temperature and time.
Use & Care Notes: • For best results, use rack position 2 or 3 when using the Rapid Preheat option. • For optimum baking and browning results, Rapid Preheat is not recommended when baking on multiple racks. • The oven has a variable broil feature which means that a lower broil temperature can be selected (300°-550° F). To select a lower temperature, press the appropriate number pads. Press Enter pad to set the lower temperature. 4. Preheat the oven for five minutes. 5.
Use & Care OPTIONS More Options Cook & Hold 5. The display will show CONVECT DELAY, the selected function, the preset temperature and the delay time countdown. When the delay time has expired, the cook time will be displayed and the oven will begin to preheat. 1. Press the More Options pad. To set Delay Clean: 2. Select COOK/HOLD. 1. Follow “Delay” steps 1-4 (see below left). 2. REMOVE RACKS will show in the display. Remove the racks from the oven and select CONTINUE. 3.
Use & Care Keep Warm Meat Probe The Keep Warm feature is used to safely keep hot foods warm or for warming breads and plates. Using the probe supplied with your oven assures excellent roasting results every time. 1. Press More Options pad. 1. Insert the probe into the food item. For meats, the probe tip should be located in the center of the thickest part of the meat and not into the fat or touching a bone. 2. Insert the probe plug into the receptacle located on the top right of the oven.
Use & Care 9. When the selected internal temperature of the food has been reached, the oven will shut off and a beep will sound. 10. Remove the probe from the oven receptacle. The probe will be hot. Hold probe plug with an oven mitt or potholder when removing from the oven.
Use & Care 2. Press arrow key to scroll. 5. Select ENTER to save name. 6. Select cooking mode, such as BAKE, CONVECT BAKE, CONVECT ROAST, etc. 7. Select the oven temperature using the Quickset pads. 3. Select EDIT RECIPE. 4. Select desired recipe to edit. You may need to press arrow key to find desired recipe. OR 5. Follow menu to revise recipe settings as desired. Enter the desired temperature using the number pads. 6. The display will return to the Favorites menu. RECIPE LIST will be displayed. 8.
Use & Care To reactivate Auto Convect Conversion: 5. Select ON or OFF. 1. Press Setup pad. 6. Press Setup pad to exit the Setup menu. 2. Select AUTO CONVECT. To cancel Sabbath Mode: 3. Select ON. Press and hold the Setup pad for five seconds. The Bake mode may be cancelled by pressing the CANCEL pad during Sabbath. 4. Press Setup pad to exit the Setup menu.
Use & Care Tones (beeps) 3. Select 12HR SHUTOFF. The number of beeps heard at the end of cooking and at the end of timer operation and their volume can be adjusted. 3. Select ON or OFF using the Quickset pads. To adjust the beeps: 1. Press Setup pad. 4. Press the Setup pad to exit. Energy Saver 2. Use the arrow to scroll. 3. Select TONES. To save energy, the display can be set to go dark if it is not being used. To change the beeps at the end of cooking: To set the Energy Saver feature: 1.
Appendix C © 2006 Maytag Services 16026923 C–1
Gas Conversion Instructions, JGS8750BD* Part No. 8101P684-60 This range is equipped with fixed orifices on all burners and a convertible appliance regulator. The unit serial plate states which gas it was adjusted for at the factory. To convert the unit to either Natural gas or LP gas will require replacement of the oven orifice hoods, and the top burner orifice hoods, and adjustment of the oven burner shutters and the appliance pressure regulator converter cap.
Gas Conversion Instructions, JGS8750BD* 10 12 11 NATURAL/NATUREL/GAS NATURAL Unscrew the regulator cap./Dévissez le capuchon du détendeur./Desenrosque la tapa del regulador. 13 Remove the plastic cap./Retirez le capuchon en plastique./Retire la tapa de plástico. 14 PROPANE/PROPANE/PROPANO Flip the regulator cap and replace the plastic cap./Abattez le capuchon du détendeur et installez le capuchon en plastique./Invierta la tapa del regulador y vuelva a colocar la tapa de plástico.
Gas Conversion Instructions, JGS8750BD* 22 .0430 1 Green/ Vert/ Verde .0430 24 23 1 1 2 2 Install green .0430 LP broil orifice hood. (4-5 turns-DO NOT OVERTIGHTEN)/Installez la tête du gicleur de gril, verte .0430 pour GPL. (4 à 5 tours – NE SERREZ PAS TROP)/Instale la caperuza verde de 0,0430 para gas LP del orificio del quemador de asar. (4 a 5 vueltas – NO APRIETE DEMASIADO) Place the broil burner on the broil orifice hood. CAUTION: Carefully insert burner pin in oven back.
Gas Conversion Instructions, JGS8750BD* Low Flow Adjustment/Réglage bas débit/Ajuste del flujo minimo 33 32 34 1/8" Flat head Screwdriver/ Tournevis à lame plate de 1/8 po/ Destornillador de 1/8” de cabeza plana NOTE: Repeat steps 33-37 for all burners. RMARQUE: Répétez les étapes 33 à 37 pour tous les brûleurs. NOTA: Repita los pasos 33 al 37 para todos los quemadores. 35 Adjust each surface burner one at a time. Light burner and turn to lowest setting. Remove knob.
Gas Conversion Instructions, JGS8850BD*, JGS8860BD* Rev 1-1/06 Gas Updraft/Part No. 8101P724-60 This range is equipped with fixed orifices on all burners and a convertible appliance regulator. The unit serial plate states which gas it was adjusted for at the factory. To convert the unit to either Natural gas or LP gas will require replacement of the oven orifice hoods, and the top burner orifice hoods, and adjustment of the oven burner shutters and the appliance pressure regulator converter cap.
Gas Conversion Instructions, JGS8850BD*, JGS8860BD* 7 Caution: Burner igniter is fragile./Attention: L’allumeur de brûleur est fragile./Precaución: El encendedor del quemador es frágil. 9 8 1 Lift up and remove oven bottom./Soulevez la sole du four et retirez-la./Levante y retire el fondo del horno. 10 Remove bake burner screws./Retirez les vis du brûleur de cuisson au four./Retire los tornillos del quemador de horneado.
Gas Conversion Instructions, JGS8850BD*, JGS8860BD* 16 18 17 49 2 2 1 Screw the cap securely back into place. DO NOT OVER TIGHTEN./ Revissez bien le chapeau. NE LE SERREZ PAS TROP FORT./ Enrosque la tapa firmemente en su lugar. NO APRIETE DEMASIADO. You MUST start bake and broil hoods by hand to avoid cross threading. Locate oven orifice hood from the front./Identifiez la tête de gicleur du four par l'avant./Ubique la caperuza del orificio del quemador del horno desde la parte delantera.
Gas Conversion Instructions, JGS8850BD*, JGS8860BD* 23 24 2 .0430 1 Green/ Vert/ Verde .0430 25 1 1 1 2 .52 3 2 Remove #52 natural broil orifice hood./Retirez la tête du gicleur de gril n° 52 pour gaz naturel./Retire la caperuza del orificio de gas natural #52 del quemador de asar. Install green .0430 LP broil orifice hood. DO NOT OVERTIGHTEN./Installez la tête du gicleur de gril, verte .0430 pour GPL. NE SERREZ PAS TROP.
Gas Conversion Instructions, JGS8850BD*, JGS8860BD* 31 NATURAL/NATUREL/GAS NATURAL 31A 32 White Blanc Blanco .80 mm .55 mm 1.65mm Orange Orange Naranja .97 mm IMPORTANT: Remove and keep old natural gas orifice hoods./IMPORTANT: Retirez et conservez les anciennes têtes de gicleur pour gaz naturel./IMPORTANTE: Retire y conserve las tapas usadas de los orificios de gas natural. Replace with LP gas orifice hoods. DO NOT OVERTIGHTEN./Remplacez-les avec des têtes de gicleur pour GPL. NE SERREZ PAS TROP.
Gas Conversion Instructions, JGS8850BD*, JGS8860BD* 38 39 40 Adjust flame height with screwdriver./Ajustez la hauteur de la flamme avec le tournevis./Ajuste la altura de la llama con el destornillador. NOTE: Double burner only./REMARQUE: Brûleur double uniquement./NOTA: Quemador doble solamente. Adjust double surface burner. Light burner and turn to lowest setting where both inner and outer ring are lit. Remove knob./Ajuster le brûleur de surface double.
Gas Conversion Instructions, JGS8850BD*, JGS8860BD* 46 48 47 1 2 Replace panel and screws./Remettez le panneau et les vis./Vuelva a instalar el panel y los tornillos. 49 Move hinges into the first stop position./Placez les charnières à la première position d’arrêt./Mueva las bisagras al primer tope. C – 12 Replace warming drawer./Replacez le tiroir de réchauffage./Vuelva a instalar el cajón de calentamiento. 50 Replace oven rack./Remettre la grille de four./Vuelva a instalar la rejilla del horno.
Gas Conversion Instructions, JGS9900BD* Rev 2-1/06 Gas Downdraft/Part No. 8101P725-60 This range is equipped with fixed orifices on all burners and a convertible appliance regulator. The unit serial plate states which gas it was adjusted for at the factory. To convert the unit to either Natural gas or LP gas will require replacement of the oven orifice hoods, and the top burner orifice hoods, and adjustment of the oven burner shutters and the appliance pressure regulator converter cap.
Gas Conversion Instructions, JGS9900BD* 1/2" (12.5 cm) 10 2 You MUST start bake and broil hoods by hand to avoid cross threading. 11 .047/ Orange/ 0,047/ Orange/ .047 Naranja 1 1 Vous DEVEZ insérer les têtes de gicleur de cuisson et de gril à la main afin d’éviter qu’un filetage ne soit faussé. 3 #50 Usted DEBE iniciar el enroscado de las tapas de horneado y asado a mano para evitar dañar las roscas. Remove brass orifice hood./Retirez la tête de gicleur en laiton.
Gas Conversion Instructions, JGS9900BD* 20 21 22 NATURAL/NATUREL/GAS NATURAL Unscrew the regulator cap./Dévissez le capuchon du détendeur./Desenrosque la tapa del regulador. Remove the plastic cap./Retirez le capuchon en plastique./Retire la tapa de plástico. Screw the cap securely back into place. DO NOT OVER TIGHTEN./ Revissez bien le chapeau. NE LE SERREZ PAS TROP FORT./ Enrosque la tapa firmemente en su lugar. NO APRIETE DEMASIADO. Remove the top grates. Remove the burner caps.
Gas Conversion Instructions, JGS9900BD* 30 31 Turn on gas and electrical supply to product. Ouvrez le gaz et l'électricité alimentant l'appareil. Abra el suministro de gas y conecte el suministro eléctrico al producto. NOTE: When reversing an LP conversion back to natural gas, the LP choke in step 29 MUST be removed. REMARQUE : Lorsque vous faites une reconversion du GPL au gaz naturel, l’étrangleur pour GPL de l’étape 29 DOIT être retiré.
Gas Conversion Instructions, JGS9900BD* 41 42 CORRECT BON CORRECTO 43 YELLOW (Open shutter to correct) JAUNE Ouvrez l'obturateur pour rectifier AMARILLA Abra el obturador para corregir la situación. BLUE LIFTING 1 (Close shutter to correct) FLAMME BLEUE SE SOULEVANT Fermez l'obturateur pour rectifier AZUL QUE SE SEPARA DEL QUEMADOR 2 Cierre el obturador para corregir la situación. Replace knobs. Turn OFF burners./Remettez les boutons. Mettez les brûleurs sur OFF (ARRÊT).