JENN-AIR® BOTTOM MOUNT BUILT-IN REFRIGERATOR REFRIGERADOR EMPOTRADO CON CONGELADOR EN LA PARTE INFERIOR DE JENN-AIR® RÉFRIGÉRATEUR ENCASTRÉ AVEC CONGÉLATEUR EN BAS JENN-AIR® INSTALLATION GUIDE For questions about features, operation/performance, parts, accessories, or service, call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com. In Canada, call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.ca.
TABLE OF CONTENTS REFRIGERATOR SAFETY........................................................................... 3 36" MODELS ................................................................................................ 4 42" FRENCH DOOR MODELS.................................................................... 4 INSTALLATION REQUIREMENTS ............................................................. 4 Tools and Parts.........................................................................................
REFRIGERATOR SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.
36" MODELS 42" FRENCH DOOR MODELS Euro-Style Design Features stainless steel wrapped doors with towel bar handles. JB36SSFXRA JB36SSFXLA Euro-Style Design Features stainless steel wrapped doors with towel bar handles. JF42SSFXDA INSTALLATION REQUIREMENTS Tools and Parts IMPORTANT: ■ Installer: Leave Installation Instructions with the homeowner. ■ Homeowner: Keep Installation Instructions for future reference. Save these Installation Instructions for the local electrical inspector’s use.
Location Requirements A The refrigerator can be recessed in an opening between cabinets or installed at the end of a cabinet run using a side panel to enclose the refrigerator. B ¹⁄₂" (1,3 cm) WARNING A. Gasket B. Compressor cover Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can result in death, explosion, or fire. ■ A grounded 3 prong electrical outlet should be placed within 4" (10.2 cm) of the right side cabinets or end panel.
Electrical Requirements WARNING 6" (15.2 cm) Electrical Shock Hazard 6" (15.2 cm) Plug into a grounded 3 prong outlet. 1" (2.54 cm) 6" (15.2 cm) 24" (60.96 cm) min. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. ■ If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor. A ¹⁄₂" (12.7 mm) hole for plumbing should be drilled at least 6" (15.2 cm) from the right or left hand side cabinet or panel.
Tipping Radius Be sure there is adequate ceiling height to stand the refrigerator upright when it is moved into place. ■ The dolly wheel height must be added to the tipping radius when a dolly is used. ■ If needed, the tipping radius can be reduced. See “Reduce Tipping Radius.” Product Dimensions Side View ■ The power cord is 84" (213 cm) long. ■ The water line attached to the back of the refrigerator is 5 ft (1.5 m) long.
42" (106.7 cm) Models 42" (106.7 cm) Models 41¹⁄₄" (105 cm) 25³⁄₈" (64.5 cm) NOTE: Add up to 2¹¹/₁₆" (6.74 cm) for the handles. *83³⁄₈" (211.8 cm) Front View ■ Width dimensions were measured from trim edge to trim edge. ■ Height dimensions are shown with leveling legs extended ¹⁄₈" (3 mm) below the rollers. 36" (91.4 cm) Models 42¹⁄₄" (107.3 cm) *When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions. *83³⁄₈" (211.
Side Trim 42" (106.7 cm) Models ¹⁄₄" (6.35 mm) ¹¹⁄₆₄" (4.5 mm) 40⁷⁄₁₆" (102.7 cm) 13¹⁄₂" (34.3 cm) max. ³⁄₁₆" (4.7 mm) ⁷⁄₃₂" (5.5 mm) 44¹⁄₄" (112.3 cm) 90˚ 110˚ 130˚ 90˚ 110˚ 130˚ ¹³⁄₃₂" (10 mm) Euro-Style Door Handle Kits All factory parts are available through your Jenn-Air dealer or by calling Jenn-Air at 1-800-JENN-AIR (1-800-536-6247). In Canada, call 1-800-807-6777. 36" Models: #W10197087 42" Models: #W10197088 Follow the kit instructions for installing the door handles. ⁵⁄₈" (15.
INSTALLATION INSTRUCTIONS Unpack the Refrigerator 2. Push the top grille straight up; then pull straight out. Lay the grille on a soft surface. B A B WARNING Tip Over Hazard Refrigerator is top heavy and tips easily when not completely installed. Keep doors taped closed until refrigerator is completely installed. Use two or more people to move and install refrigerator. Failure to do so can result in death or serious injury. A. Top grille B. Cabinet side trim 3.
42" (106.7 cm) Models A B C 2" (5 cm) D 2. Place pieces of the shipping carton on the floor when rolling the dolly and refrigerator into the house. Move the refrigerator close to the built-in opening. 3. Place top of cardboard carton or plywood under refrigerator. 4. Stand the refrigerator up. First, place the left bottom edge of the refrigerator on the floor, stand the refrigerator upright and then lower the right-hand side of the refrigerator to the floor. 5. Do not remove film or cover. 6.
Connecting to Refrigerator Style 2—Copper Line Connection Connecting to Water Line NOTE: If existing water line meets the “Water System Requirements,” see “Connecting to Refrigerator.” 1. Unplug refrigerator or disconnect power. 2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water. 3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator. IMPORTANT: ■ Make sure it is a cold water pipe.
Move Refrigerator to Final Location After moving the refrigerator to its final location: 1. Use a ⁵⁄₁₆" socket driver to turn the leveling bolts clockwise to extend the legs to the floor as shown. The rollers should be off the floor. WARNING A A B B Tip Over Hazard Refrigerator is top heavy and tips easily when not completely installed. Keep doors taped closed until refrigerator is completely installed. Use two or more people to move and install refrigerator.
Adjust Door(s) Door Alignment (36" [91.4 cm] Models) 1. Loosen, but do not remove, the four Torx®† 27 flat-head mounting screws and the two ¹⁄₄" hex-head mounting screws in the top hinge. 2. Adjust the top hinge of the door to align it. 3. Tighten the Torx®† 27 flat-head mounting screws to a torque of approximately 100 inch-pounds (11.3 Nm). 4. Tighten the ¹⁄₄" hex-head screws. A 3. Turn the bushing located underneath the bottom of the hinge using a ¹⁄₂" open-end wrench.
42" (106.7 cm) Models 1. Check that the refrigerator door can open freely. If the door opens too wide, you will have to adjust the door stop position. 2. Grasp both ends of the top grille. 3. Push the top grille straight up, then pull straight out. Lay the grille on a soft surface. B A 6. Reverse or rotate the door stop to the desired position as shown below.
Install Base Grille Complete Installation There are two pieces to the base grille to allow for a custom fit: the base grille itself and the skirt. The skirt can be added to the base grille in order to extend it all the way to the floor. 1. To see whether the skirt is needed, place the base grille into position. Do not attach the base grille to the refrigerator. Measure the distance between the bottom of the base grille and the floor. The gap must be a minimum of ¹⁄₂" (1.27 cm) in order to add the skirt.
Notes 17
® W10728799A /™ ©2014 Jenn-Air. Used under license in Canada. All rights reserved. Usada en Canadá bajo licencia. Todos los derechos reservados. Utilisé sous licence au Canada. Tous droits réservés. 7/14 Printed in U.S.A. Impreso en EE.UU. Imprimé aux É.-U.