Flush Kit Installation Instructions

8
Install Deector Kit Bracket
This assembly is required for use when a single or double built-in
oven is installed in a ush installation
1. Flex the upper vent piece (C) away from the lower vent
piece (D) to slide the deector bracket (B) between them.
Some force may be required to ex the upper vent trim (C)
away from the lower vent trim (D). Some force may also
be required to ex the deector bracket (B) and slide it
into position. Make sure screw holes are properly aligned
between the two pieces. See the following illustration.
2. Install the deector bracket (B) to the lower vent piece (D)
using two #8-18 x 1/4" (6.3 mm) screws on each side.
NOTE: On 27" (68.6 cm) models, only one #8-18 x 1/4"
(6.3 mm) screw is used on each side.
3. Align vent tab (B) with oven frame (A) as shown.
4. Using one #8-18 x 3/8" (9.5 mm) screw (E) on each side of
the vent tab (B), fasten the vent securely to the oven.
5. Replace the oven racks.
6. Replace the oven door. See the “Replace Oven Door(s)"
section.
7. Check that the door is free to open and close. If it is not,
repeat the removal and installation procedures. See the
“Prepare Built-In Microwave/Oven Combination” section.
8. Reconnect power.
9. The display panel will light briey, and “PF” should appear in
the display.
10. If the display panel does not light, refer to the “Assistance
or Service” section of the Use and Care Guide provided
with your built-in oven or contact the dealer from whom you
purchased your oven.
Complete Installation
1. Check that all parts are now installed. If there is an extra
part, go back through the steps to see which step was
skipped.
2. Check that you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. For oven use and cleaning, read the Use and Care Guide.
Check Operation of Lower Oven
1. Turn on power.
2. At rst use, set up the clock and any other preferences
if available. For more information, read the Use and Care
Guide.
3. Press BROIL.
4. Set the temperature.
5. Press START.
If oven(s) does not operate, check the following:
■ Household fuse is intact and tight; or circuit breaker has
not tripped.
■ The electrical supply is connected.
■ See “Troubleshooting” section in the Use and Care
Guide.
6. When oven has been on for 5 minutes, feel for heat.
If you do not feel heat or if an error message appears in the
display, turn off the oven and contact a qualied technician.
7. Press CANCEL OVEN.
Check Operation of Microwave Oven
1. Fill a microwave-safe container with 1 cup (250 mL) of water
and place the container inside the microwave oven. Close
the door rmly.
2. Press COOK and set the microwave oven cook time to
“2:00” minutes.
3. Press START. The interior microwave oven light should be
on, and the remaining cooking time should be displayed.
When the display reads “1:00” minute, open the microwave
oven door. The microwave should stop cooking. Close the
door rmly. The interior microwave oven light should turn off.
4. Press START. The microwave oven should begin cooking and
the microwave oven interior light should be on.
Let the microwave oven complete the cooking time. A tone
will sound 4 times at the end of the cooking time and the
microwave oven will shut off.
5. Open the microwave oven door and slowly remove the
container. Water in the container should be hot.
If you need Assistance or Service:
Please refer to the “Assistance or Service” section in the Use
and Care Guide or contact the dealer from whom you purchased
your built-in oven.
C. Upper vent piece (supplied with oven)
D. Lower vent piece (supplied with oven)
A. #8-18 x 1/4" (6.3 mm)
screws
B. Deflector bracket
D
B
A
C
B
D
C
A. Oven frame
B. Vent tab
C. Oven vent
A
C
D
B
E
D. Deflector bracket
E. #8-18 x 3/8" (9.5 mm)
screw
06-May-2019 13:38:42 EDT | RELEASED
In some European factories the letter "W" of the part code mentioned herein will be automatically
replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")