Installation guide

ManualsBrandsJenn-Air ManualsRangeOfficial Jenn-Air electric slide-in range

Range

Models SVE47600, SVE47500,

SVE47100, SCE30600, SCE30500

_'JENN-AIR

403WESTFOURTHSTREET,NORTH• NEWTON,IA50208

INSTRUCTIONSTO INSTALLER:"Important: Savefor localelectricalinspector'suse".

Range Overall Dimensions:

Width - 29-15/16" (76.04 cm)

Depth - 26-3/8" (70.00 cm)

Height - 35-1/2" (90.17 cm)

*Add 2" (5.08 cm) for door handle

I WARNING

_'_ II_I1' ALL RANGES CAN TIP AND

I AUSEINJURIESTOPERSONS.

I" INSTALL ANTI-TIP DEVICES

I PACKED WITH RANGE.

'!" FOLLOW ALL INSTALLATION

I INSTRUCTIONS.

ELECTRICAL SPECIFICATIONS: 120/240 VAC OR 120/208 VAC 60 Hz 50 amp circuit protection recommended,

40 amp minimum required. Wire size: For 50 amp service use #6 60°C or #8 75°C (copper only) three or four

conductor, for 40 amp service use #8 (copper only) three or four conductor.

ELECTRICAL CONNECTION: Unitto be properly circuitprotected and wired according to local electrical code and

national electric code. Unit power requirements located on serial plate on front of range.

8101P265-60

(06-99-01)

Summary of content (8 pages)

PAGE 1
Range _'JENN-AIR Models SVE47600, SVE47500, SVE47100, SCE30600, SCE30500 403WESTFOURTH STREET, NORTH• NEWTON, IA 50208 INSTRUCTIONSTO INSTALLER:"Important: Savefor local electricalinspector'suse". I _'_ Range Overall Dimensions: Width - 29-15/16" (76.04 cm) Depth - 26-3/8" (70.00 cm) Height - 35-1/2" (90.17 cm) *Add 2" (5.08 cm) for door handle II_I1' I SPECIFICATIONS: 120/240 RANGES CAN TIP AND AUSEINJURIESTO PERSONS.
PAGE 2
,1. Unpack Range (Figure 1) • Cut and remove shipping carton. • Remove lower range panel or drawer, and place out of work area. • Remove blower package (if you have not already done so.) (Downdraft Models Only.) • Locate Ducting Instruction sheet. (Downdraft Models Only.) NOTE:Please read through entire installation instructions and ducting instructions prior to beginning installation. = Select Range Location (Figure 2) • Carefully select the range location, keeping in mind the following: A.
PAGE 3
5. Slide-In Cutout (Figure 5) • Use the overhang measurement to figure the "A"dimension: Overhang 1t2" (1.27 cm) to 1" (2,54 cm) Overhang 1" (2.54 cm) to 1-3/4" (4.45 cm) .... "A" = 22-5t8" (57.47 crn) .... "A" = 23" (5-5.42 cm) • Carefully mark the countertop and recheck you dimensions. • Before you cut, check the rear countertop dimensions. (See #6.) NOTE: The minimum clearance between the cutout and cabinet doors and drawer edge is 7/8". 6.
PAGE 4
11. Wall Vent Cutout (Figure 11) • Locate the vertical studs in the rear wall. Studs are usually 16" (40.64 cm) center to center. • Will the vent duct be 6" (t5.24 cm) round through the wall or 3-1/4" x 10" (8.26 cmx 25.4 crn) rectangle, vertically inside the walt? • See Ducting Instructions for rear duct inside the wall. Note: Cutout in the wall must clear 3-1/4" x 10" (8.26 cm x 25.4 cm) transition elbow. • Locate the closest stud to your proposed vent hole location.
PAGE 5
15. P.._onnectElectrical (Four Conductor Wire) (Figure 15) • CAUTION: Make sure power to cable is OFF. • Remove the range electrical service cover, located on the back, lower left-hand corner. • Remove the groun strap screw and bend the strap up as shown. Install a3/4" (1.91 cm) cable clamp in the hole provided, below the terminal block. • Strip 3" (7.62 cm) of outer insulation from the cable. • Strip 1/2" (1.27 cm) of insulation from each wire. • Pull the cable through the cable clamp.
PAGE 6
19. Level Range (Figure 19) • Free-Standing. Adjust the leveler feet to level range with the countertop. • Slide-In. Adjust the leveler feet to take some of the weight offof the countertop. • Unit must be level for optimum baking performance. Check levelness inside oven using a level that is placed on oven rack. • For non-downdraft units go to step 22. (Figure 19) 20.
PAGE 7
Additional instructions for venting through the base cabinet toe space on either side of the range when it is not possible to vent through the floor or through a rear wall. Additional Materials Required 1.5" Dia, x 19" long (12.7 cmx 48.26 cm) Flex Duct* (P/N 702935) 1, 6" (15.24 cm) 90 ° Elbow T Left Cabinet Right Cabinet 31.19" _2cr. 2. Hose Clamps* (P/N 702331 ) 1.5" to 3-1/4" x 10" (12.7 cm to 8.26 cm x 25.4 cm) Transition* 2. Wood Spacers (right side vent only) 1-1/2" Thick x 9" Long (3.
PAGE 8
Step 4 Attach the blower housing to the floor with the outlet toward the direction of venting and the inlet toward the front of the cabinets. (See Figures 2 and 3 for specific location.) In addition, for left side venting, a spacer approximately 1-1/2" thick x 9" long (3,81 cm x 22.86 cm) is required under the mounting bracket flanges of the blower assembly. (See Figure 5.) Right Side Venting Left Side Venting Step 5 Remove the inside wire and the outside string from the first 1-1/2 inches (3.